聚丙烯微阵列结构制品熔体充填行为

doi:10.3969/j.issn.0438-1157.2013.08.049

化工学报 ›› 2013, Vol. 64 ›› Issue (8): 3045-3053.DOI: 10.3969/j.issn.0438-1157.2013.08.049

• 材料化学工程与纳米技术 • 上一篇下一篇

聚丙烯微阵列结构制品熔体充填行为

张勤星, 李倩, 董自开, 蒋晶, 王利霞, 申长雨

郑州大学橡塑模具国家工程研究中心, 河南郑州 450002

收稿日期:2012-12-19 修回日期:2013-01-10 出版日期:2013-08-05 发布日期:2013-08-05
通讯作者: 李倩
作者简介:张勤星(1978- ),男,博士研究生,讲师。
基金资助:
国家重点基础研究发展计划项目(2012CB626809)。

Filling behavior of iPP micro-array structure product by micro injection molding

ZHANG Qinxing, LI Qian, DONG Zikai, JIANG Jing, WANG Lixia, SHEN Changyu

National Engineering Research Center for Advanced Polymer Processing Technology, Zhengzhou University, Zhengzhou 450002, Henan, China

Received:2012-12-19 Revised:2013-01-10 Online:2013-08-05 Published:2013-08-05
Supported by:
supported by the National Basic Research Program of China(2012CB626809).

摘要/Abstract

摘要： 根据微阵列结构制品熔体的充填特性,设计直径为500 μm的微圆柱阵列结构制品模型,并加工注射成型模具,对微圆柱结构制品熔体的充填规律进行实验和模拟研究。结果表明:微结构制品熔体的充填过程和流动前沿形态的实验结果与模拟分析虽然在趋势上比较一致,但在微圆柱成型过程中,流动前沿的形成过程和充填高度的模拟变化规律与实验结果有一定偏差;实验还发现,前期充填阶段对微圆柱成型的贡献较小,微圆柱内流动前沿的形成受到熔体流动速度、微圆柱模壁、熔体流动惯性影响较大,熔体流经微圆柱结构时产生向上的流动涡流,流动前沿形状呈偏心椭球冠状并逐渐发展成球冠状。

关键词: 微阵列结构, 充填行为, 流动前沿, 偏心椭球冠状, 球冠状

Abstract: Filling behavior of micro-array structure product of iPP was investigated by numerical analysis and injection molding experiments.An injection mold was designed to produce products with micro-cylinder structure 500 μm in diameter.The filling process of flow front of micro-cylinders of numerical simulation and injection molding experiment was relatively consistent in the general trend.However,formation of flow front and varying patterns of the height of micro-cylinder in the filling process in the numerical simulation deviated from the experiment.Injection molding experiment showed that micro-cylinder mold wall,melt flow rate,and melt flow inertia played an important role in the formation of flow front.Early filling contributed little to the micro-cylinder molding.Turbulence appeared on the melt flow directly below the micro-cylinder.The flow front was like the shape of acentric ellipsoid crown and gradually developed into the shape of spherical crown.

Key words: microarray structure, filling behavior, flow front, shape of acentric ellipsoid crown, shape of spherical crown

中图分类号:

TQ320.66⁺2

张勤星, 李倩, 董自开, 蒋晶, 王利霞, 申长雨. 聚丙烯微阵列结构制品熔体充填行为[J]. 化工学报, 2013, 64(8): 3045-3053.

ZHANG Qinxing, LI Qian, DONG Zikai, JIANG Jing, WANG Lixia, SHEN Changyu. Filling behavior of iPP micro-array structure product by micro injection molding[J]. CIESC Journal, 2013, 64(8): 3045-3053.

参考文献 16

[1]	Heckele M,Schomburg W K.Review on micro molding of thermoplastic polymers[J].J. Micromech. Microeng.,2004,14(3):R1-R14
[2]	Piotter V,Mueller K,Plewa K,Ruprecht R,Hausselt J.Performance and simulation of thermoplastic micro injection molding[J].Microsystem Technologies,2002,8(6):387-390
[3]	Attia Usama M,Marson Silvia,Alcock Jeffrey.Micro-injection moulding of polymer microfluidic devices[J].Microfluid Nanofluid,2009,7(1):1-28
[4]	Liou A C,Chen R H.Injection molding of polymer micro-and sub-micron structures with high-aspect ratios[J].Int. J. Adv. Manuf. Tech.,2006,33(11/12):1097-1103
[5]	Kim S H,Shiau C S,Kim B H,Yao D G.Injection molding nanoscale features with the aid of induction heating[J].Polym.-plast. Technol.,2007,46(10/12):1031-1037
[6]	Tosello G,Hansen H N,Cirp Gasparin S.Applications of dimensional micro metrology to the product and process quality control in manufacturing of precision polymer micro components[J].Ann-manuf. Techn.,2009,58(1):467-472
[7]	Giboz J,Copponnex T,Mele P.Microinjection molding of thermoplastic polymers:a review[J].J. Micromech. Microeng.,2007,17(6):R96-R109
[8]	Yu L Y,Koh C G,Lee L J,Koelling K W,Madou M J.Experimental investigation and numerical simulation of injection molding with micro-features[J].Polmy. Eng. Sci.,2002,45(2):871-888
[9]	Sha B,Dimov S,Griffiths C,Packianather M S. Investigation of micro-injection moulding:factors affecting the replication quality[J].J. Mater. Process Tech.,2007,183(2/3):284-296
[10]	Zhang K F,Lu Zhen.Analysis of morphology and performance of PP microstructures manufactured by micro injection molding[J].Microsyst. Technol.,2008,14(2):209-214
[11]	Lin Huang-Ya,Young Wen-Bin.Analysis of the filling capability to the microstructures in micro injection molding[J].Appl. Math. Model,2009,33(9):3746-3755
[12]	Zhang H L,Ong N S,Lam Y C. Experimental investigation of key parameters on the effects of cavity surface roughness in microinjection molding[J].Int. J. Adv. Manuf. Tech.,2008,31(11/12):1105-1112
[13]	Tsai M H,Ou K L,Huang C F,Cheng H C,Shen Y K,Chang C Y,Wu C H,Chen J H,Guan P J.Injection molding of light guiding plate by numerical simulation[J].Int. Commun. Heat Mass,2008,35(9):1097-1100
[14]	Kim Y,Choi Y,Kim Y J,Kang S.Construction of injection mold with MEMS RTD sensor and MEMS heater for micro/nano molding process[J].Jpn. J. Appl. Phys. Part 1-Regul. Pap. Brief Commun. Rev. Pap.,2005,44(5B):3591-3595
[15]	Zhuang Jian(庄俭),Wu Daming(吴大鸣),Zhao Zhongli(赵中里),Zhang Hongbo(张洪波).Experimental investigation into process of micro injection molding[J].CIESC Journal(化工学报),2009,60(4):1040-1045
[16]	Shen Yung-Kang,Chang Chih-Yuan,Shen Yu-Sheng,Hsu Sung-Chih,Wu Ming-Wei.Analysis for microstructure of microlens arrays on micro-injection molding by numerical simulation[J].Heat and Mass Transfer,2008,35:723-727

聚丙烯微阵列结构制品熔体充填行为

Filling behavior of iPP micro-array structure product by micro injection molding

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献 16

相关文章 0

编辑推荐

Metrics

本文评价