自吸式文丘里洗涤器引射特性及其影响因素

doi:10.11949/j.issn.0438-1157.20141131

化工学报 ›› 2015, Vol. 66 ›› Issue (1): 99-104.DOI: 10.11949/j.issn.0438-1157.20141131

自吸式文丘里洗涤器引射特性及其影响因素

周艳民, 孙中宁, 谷海峰, 苗壮

哈尔滨工程大学核安全与仿真技术国防重点学科实验室, 黑龙江哈尔滨 150001

收稿日期:2014-07-28 修回日期:2014-10-09 出版日期:2015-01-05 发布日期:2015-01-05
通讯作者: 周艳民

Injection performance and influencing factors in self-priming Venturi scrubber

ZHOU Yanmin, SUN Zhongning, GU Haifeng, MIAO Zhuang

Nuclear Safety and Simulation Technology Key Laboratory of National Defense Disciplines, Harbin Engineering University, Harbin 150001, Heilongjiang, China

Received:2014-07-28 Revised:2014-10-09 Online:2015-01-05 Published:2015-01-05

摘要/Abstract

摘要：

以自吸式文丘里洗涤器为研究对象, 基于伯努利方程分析了影响其引射量的主要因素, 并通过实验对各因素进行分析验证。结果表明, 自吸式文丘里洗涤器的引射量主要取决于吸液口两侧的静压差、截面积、高度差以及液体在流动通道内的阻力系数。当文丘里洗涤器不引射液体时, 液体流动通道出口截面上的静压力与喷嘴壁面处的压力相等, 远高于喷嘴出口中心和出口平均压力;当文丘里洗涤器引射液体时, 气液两相的动量交换作用, 会在气液界面处产生额外的压力增量, 并以压力波的形式向整个截面传递, 导致有效的吸液压差进一步降低。当吸液压差较小时, 液体的流通面积和阻力系数对引射量的影响明显, 通过增大外套管与喷嘴面积比同时增大喷管出口直径的方法, 一方面能够增大液体流通面积, 另一方面也减小了液相流动阻力, 对于改善液体引射量是有效的。

关键词: 自吸式文丘里洗涤器, 引射量, 静压分布, 动量传递

Abstract:

The main factors that affect injection performance of self-priming Venturi scrubber were analyzed based on the Bernoulli equation, the influence of these factors was further verified by experiment. Injection flow rate of self-priming Venturi scrubber depended mainly on static pressure differential, cross-sectional area, height difference and liquid channel resistance coefficient on both sides of suction port. In the case of no injection, the static pressure at outlet cross section of liquid flow was equal to the pressure at nozzle wall, higher than the average pressure and center pressure at nozzle exit. In the case of injecting liquid, an additional pressure increment was generated at gas-liquid interface because of momentum exchange. Pressure increment would spread around in the form of pressure waves to the entire cross-section, resulting in further reduction of effective pressure difference for injection. When effective injection pressure difference was limited, liquid channel area and resistance coefficient became important for injection flow. On this occasion, it was more effective to enlarge the area ratio between nozzle and sleeve and enlarge nozzle diameter, to increase liquid channel area and reduce resistance coefficient, which was effective in increasing liquid flow.

Key words: self-priming Venturi scrubber, injection flow rate, static pressure distributions, momentum transfer

中图分类号:

TL334

周艳民, 孙中宁, 谷海峰, 苗壮. 自吸式文丘里洗涤器引射特性及其影响因素[J]. 化工学报, 2015, 66(1): 99-104.

ZHOU Yanmin, SUN Zhongning, GU Haifeng, MIAO Zhuang. Injection performance and influencing factors in self-priming Venturi scrubber[J]. CIESC Journal, 2015, 66(1): 99-104.

参考文献 20

[1]	Stephen N Rudnlck, John L M Koehler, Kenneth P Martln, Davld Lelth, Douglas W Cooper. Particle collection efficiency in a Venturi scrubber: comparison of experiments with theory [J]. Environ. Sci. Technol., 1986, 20 (3): 237-242
[2]	Wang Meng (王盟), Sun Zhongning (孙中宁), Gu Haifeng (谷海峰), Guo Xueqing (郭雪晴). Experimental study of pressure drop characteristics of Venturi scrubber working at self-priming mode [J]. Atomic Energy Science and Technology (原子能科学技术), 2012, 46 (11): 1353-1356
[3]	Zhou Zhigui (周志贵). Reactor containment decompression and filtration in Qinshan NPP phaseⅡ[D].Shanghai:Shanghai Jiaotong University, 2007
[4]	Johnstone H F, Field R B, Tassler M C. Gas absorption and aerosol collection in a Venturi atomizer [J]. Industrial and Engineering Chemistry, 1954, 46 (8): 1601-1608
[5]	Mayinger F, Neumann M. Dust collection in Venturi scrubbers [J]. Ger. Chem. Eng., 1978, 1: 289-293
[6]	Mayinger F, Lehner M. Operating results and aerosol deposition of a Venturi scrubber in self-priming operation [J]. Chemical Engineering and Processing, 1995, 34 (3): 283-288
[7]	Richard H Boll. Particle collection and pressure drop in Venturi scrubbers [J]. Ind. Eng. Chem. Fundam., 1977, 12 (1): 40-49
[8]	Ali Majid, Yan Changqi, Sun Zhongning. Dust particle removal efficiency of a Venturi scrubber [J]. Annals of Nuclear Energy, 2013, 54: 178-183
[9]	Chen Xiujuan (陈修娟), Xiao Lichuan (肖立川), Xu Jingwei (许景伟). Influence of structural parameters upon two-dimensional flow field in the ejector [J]. Thermal Power Generation, 2009, 3: 40-43
[10]	Wang Rui (王锐). Study on the performance of liqud-gas ejector [D].Dalian: Dalian Maritime University, 2009
[11]	Yuan Guofeng (原郭丰). Experimental research and three-dimensions numerical simulation of liquid jet liquid & gas ejector [D]. Xi'an: Northwestern Polytechnical University, 2007
[12]	Sokolov (索科洛夫). Ejector [M]. Beijing: Science Press, 1977: 35
[13]	Lehner M. Aerosol separation efficiency of a Venturi scrubber working in self-priming mode [J]. Aerosol Science and Technology, 1998, 28 (5): 389-402
[14]	Wang Meng (王盟), Sun Zhongning (孙中宁), Gu Haifeng (谷海峰). Development of structure design program for Venturi scrubber working in self-priming mode [J]. Atomic Energy Science and Technology (原子能科学技术), 2012, 42 (6): 701-704
[15]	Maddury Ravlndram, Naldu Pyla. Modeling of a Venturi scrubber for the control of gaseous pollutants [J]. Ind. Eng. Chem. Process Des. Dev., 1986, 26 (6): 35-39
[16]	Mousavian S, Ashouri D, abdolahi M, Vakili M H, Rahnama Y. Mathematical modelling of Venturi scrubber for ammonia absorption [J]. World Academy of Science, Engineering and Technology, 2012, 61: 625-627
[17]	Silva A M, Teixeira J C F, Teixeira S F C F. Experiments in a large-scale Venturi scrubber (Ⅰ): Pressure drop [J]. Chemical Engineering and Processing, 2009, 48: 59-67
[18]	Sun H, Azzopardi B J. Modeling gas-liquid flow in Venturi scrubbers at high pressure [J]. Trans. IChemE, 2003, 81: 250-256
[19]	Zhou Yanmin (周艳民), Sun Zhongning (孙中宁), Gu Haifeng (谷海峰), Wang Junlong (王军龙). Research on performance of pressure in self-priming Venturi scrubber throat//The 13th Conference on Nuclear Reactor Thermal Fluid [C]. Shanghai: 2013
[20]	Kong Long (孔珑). Engineering Fluid Mechanics (工程流体力学) [M]. Beijing: China Electric Power Press, 2006: 101-107

自吸式文丘里洗涤器引射特性及其影响因素

Injection performance and influencing factors in self-priming Venturi scrubber

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献 20

相关文章 3

编辑推荐

Metrics

本文评价

[1]	高思鸿, 刘堉学, 范怡平, 卢春喜. 新型旋流场-颗粒床耦合分离设备静压分布[J]. 化工学报, 2020, 71(2): 516-525.
[2]	丁思源, 王瑞祥, 徐荣吉, 张一灏, 蔡骥驰. 表面张力对自由落体液滴形变的影响[J]. 化工学报, 2016, 67(6): 2495-2502.
[3]	熊源泉;袁竹林;章名耀. 加压条件下气固喷射器输送特性的三维数值模拟 [J]. CIESC Journal, 2004, 55(10): 1638-1643.