交错螺旋折流板管壳式换热器壳侧传热与阻力性能

化工学报 ›› 2005, Vol. 56 ›› Issue (4): 598-601.

交错螺旋折流板管壳式换热器壳侧传热与阻力性能

王秋旺;罗来勤;曾敏;王良;陶文铨;黄彦平

西安交通大学动力工程多相流国家重点实验室,陕西西安 710049;空泡物理和自然循环重点实验室，四川成都 610041

出版日期:2005-04-25 发布日期:2005-04-25

Shell-side heat transfer and pressure drop of shell-and-tube heat exchangers with overlap helical baffles

WANG Qiuwang;LUO Laiqin;ZENG Min;WANG Liang;TAO Wenquan;HUANG Yanping

Online:2005-04-25 Published:2005-04-25

摘要/Abstract

摘要： 对交错搭接螺旋折流板换热器壳侧的流动与传热性能进行了实验研究，着重研究了内插假管及不同螺旋角度对壳程传热和阻力的影响，并与传统弓形折流板换热器进行了对比.结果表明，假管的存在反而使传热综合性能下降，同时，在相同的壳侧流量下，螺旋折流板换热器的壳程阻力和壳侧传热系数均随螺旋角的增大而减少，且小于同样条件下弓形折流板换热器的相应值.与弓形折流板换热器相比，螺旋折流板换热器的特点是单位压降下的壳侧传热系数高.

关键词: 交错螺旋折流板, 管壳式换热器, 假管

Abstract: The shell-side pressure drop and heat transfer performance of shell-and-tube heat exchangers with overlap helical baffles were studied experimentally in comparison with those of traditional segmental baffles heat exchangers.The influences of inserted dummy tubes and helical angles were investigated in detail. It was found that the presence of dummy tubes deteriorated the overall heat transfer performance of heat exchangers with helical baffles.The shell-side pressure drop and heat transfer coefficient decreased with the increase of helical angle at indentical shell-side mass flow rate, and both of them were lower than those of the corresponding segmental-baffle heat exchangers. The shell-side heat transfer coefficients for the helical-baffle heat exchangers were higher than those of the segmental-baffle heat exchangers at the identical shell-side pressure drop.

Key words: 交错螺旋折流板, 管壳式换热器, 假管

王秋旺, 罗来勤, 曾敏, 王良, 陶文铨, 黄彦平. 交错螺旋折流板管壳式换热器壳侧传热与阻力性能 [J]. 化工学报, 2005, 56(4): 598-601.

WANG Qiuwang, LUO Laiqin, ZENG Min, WANG Liang, TAO Wenquan, HUANG Yanping. Shell-side heat transfer and pressure drop of shell-and-tube heat exchangers with overlap helical baffles[J]. CIESC Journal, 2005, 56(4): 598-601.

[1]	王英双，张晓屿，刘志春，黄素逸，刘伟. 花格板换热器的流动与传热[J]. 化工学报, 2012, 63(S1): 99-106.
[2]	付磊，唐克伦，文华斌，王维慧，付伶. 管壳式换热器流体流动与耦合传热的数值模拟[J]. 化工进展, 2012, 31(11): 2384-2389.
[3]	曾文良，邓先和. 并流多通道管壳式换热器壳程流场分布[J]. CIESC Journal, 2011, 62(12): 3352-3360.
[4]	郭崇志，林桥. 管壳式换热器壳程流动与传热的数值模拟与验证[J]. CIESC Journal, 2011, 30(10): 2131-.
[5]	马有福，袁益超，李静芬，周文铸，胡晓红. 离心浮力对折流栅-螺旋槽管换热器传热性能的影响 [J]. CIESC Journal, 2008, 27(4): 573-.
[6]	朱冬生;蒋翔. 管壳式换热器壳程高黏度流体的传热强化 [J]. CIESC Journal, 2005, 56(8): 1451-1455.
[7]	邓斌;陶文铨. 管壳式换热器壳侧湍流流动与换热的三维数值模拟 [J]. CIESC Journal, 2004, 55(7): 1053-1059.
[8]	王杨君, 邓先和, 陈颖, 李志武. 平行流分隔板管壳式换热器壳侧流场与传热性能 [J]. 化工学报, 2004, 55(2): 275-279.
[9]	黄兴华,王启杰,陆震. 管壳式换热器壳程流动和传热的三维数值模拟 [J]. CIESC Journal, 2000, 51(3): 297-302.
[10]	徐国平,王启杰,杨小琼. 气液两相流沿垂直向下横掠水平管束时的流型及其转变特性 [J]. CIESC Journal, 1993, 44(2): 250-253.
[11]	周理,安福,徐越平. 刺孔膜片式高效管壳换热器的壳方特性研究 [J]. CIESC Journal, 1992, 43(5): 599-608.