单进口后混式射流粉碎中多相流混合机理及加速特性

doi:10.3969/j.issn.0438-1157.2013.07.016

化工学报 ›› 2013, Vol. 64 ›› Issue (7): 2418-2427.DOI: 10.3969/j.issn.0438-1157.2013.07.016

单进口后混式射流粉碎中多相流混合机理及加速特性

万继伟¹, 牛争鸣¹, 廖伟丽¹, 牛助农²

1. 西安理工大学水利水电学院, 陕西西安 710048;
2. 陕西燃气集团有限公司, 陕西西安 710016

收稿日期:2013-01-06 修回日期:2013-03-19 出版日期:2013-07-05 发布日期:2013-07-05
通讯作者: 万继伟(1983- ),男,博士研究生
作者简介:万继伟(1983- ),男,博士研究生。
基金资助:
国家自然科学基金项目(51179152);陕西省重点学科建设专项资金项目(00X902)。

Mixing mechanism of multiphase flow and acceleration performance in single inlet rear-mixed jet flow crushing

WAN Jiwei¹, NIU Zhengming¹, LIAO Weili¹, NIU Zhunong²

1. Institute of Water Resources and Hydroelectric Engineering, Xi'an University of Technology, Xi'an 710048, Shaanxi, China;
2. Shaanxi Gas Group Co., Ltd., Xi'an 710016, Shaanxi, China

Received:2013-01-06 Revised:2013-03-19 Online:2013-07-05 Published:2013-07-05
Supported by:
supported by the National Natural Science Foundation of China (51179152)and the Important Academic Special Construct Foundation of Shaanxi Province(00X901).

摘要/Abstract

摘要： 为了深入了解后混式高速水射流超细粉碎技术,以4种加速管管径条件下的液、气、固三相混合射流为对象,利用数值计算和粉碎实验相结合的方法,研究了多相混合射流相间的混合机理和加速特性,探讨了颗粒在加速空间中的分布规律。结果表明:水射流紊动掺气和卷吸作用是混合附加相的内在机理;混合射流对颗粒的加速存在分区,越靠近势流区冲击能量越大,优化喷嘴直径与加速管管径配置,迫使颗粒靠近或进入该区域可有效提高粉碎产率。颗粒在加速管内的空间分布为外层、内层高效加速区内含量最高,越靠近势流区颗粒含量越少,气流区内颗粒含量随加速管管径增大而增大。颗粒很难进入理想加速区,大部分仍依靠内、外层高效加速区加速。在保持自由射流流动形态的情况下,粉碎产率随加速管管径增大而下降,小管径对水射流能量和颗粒运动空间均具有更好的约束集中作用。

关键词: 多相射流, 混合机理, 加速特性, 射流粉碎

Abstract: In order to deeply understand the super fine crushing technology of rear-mixed high-speed water jet flow,the mixing and jetting behavior of gas-liquid-solid three phases in acceleration tube with various diameter were investigated by using numerical simulation and crushing experiment methods.Mixing mechanism and acceleration performance of multiphase mixture jet flow were explored,and particles distributions in acceleration space were obtained.The result showed that aeration and entrainment effects of jet flow turbulent motion were the inherent mechanism of mixed attached phase.There existed many partition zones in the rear-mixed jet flow for particle acceleration.Whereby the nearer to the potential flow zone,the stronger the impact energy.Accordingly,optimizing configuration of the optional nozzle diameter with the acceleration tube diameter could force the particles near or enter the potential flow zone,whereby effectively improving grinding yield efficiency.The particles in space distribution within the acceleration tube were in the highest contents in high-efficiency acceleration zones of the outer and inner layers.As a result,the nearer to the potential flow zone,the fewer the particles.The particle contents in the air flow zone increased with increasing acceleration tube diameter.It was difficult for the particles to enter the ideal acceleration zone so that most of the particles were accelerated by relying on the high-efficiency acceleration zone of the inner and outer layers.In the case of maintaining the flowing morphological state of free jet flow,the grinding yield efficiency decreased with increasing acceleration tube diameter.Accordingly small tube diameter was of better constraint and concentration functions for water jet flow energy and particle motion space.

Key words: multiphase jet, mixing mechanism, acceleration characteristics, jet flow crushing

中图分类号:

TD453
O359.1

万继伟, 牛争鸣, 廖伟丽, 牛助农. 单进口后混式射流粉碎中多相流混合机理及加速特性[J]. 化工学报, 2013, 64(7): 2418-2427.

WAN Jiwei, NIU Zhengming, LIAO Weili, NIU Zhunong. Mixing mechanism of multiphase flow and acceleration performance in single inlet rear-mixed jet flow crushing[J]. CIESC Journal, 2013, 64(7): 2418-2427.

参考文献 20

[1]	Gelecki G,Mazurkiewicz M.Hydro abrasive cutting head//Energy Transfer Efficiency[C].Berkeley,California,1987:109-111
[2]	Hlavá? L M,Vaek J,Hlavá?ová I M,Janda?ka P. Potential of liquid jets for preparation of micro and nano particles//Green Chemistry & Engineering Proc. International Conference on Process Intensification & Nanotechnology.2008:205-218
[3]	Fu Sheng(付胜),Duan Xiong(段雄),Zhang Xinmin(张新民).Effect of compressive stress release in high-pressure water jet comminution[J].China Safety Science Journal(中国安全科学学报),2004,14(1):7-10
[4]	Gong Weili(宫伟力),Fang Mei(方湄).New development of jet mill technology and study on mechanism of comminution with high pressure water jet[J].Chemical Industry and Engineering Progress(化工进展),1998(6):21-23
[5]	Marian Mazurkiewicz,Bruce E Conrad.Method of creating ultra-fine particles of materials using a high-pressure mill[P]:US,6824086 B1.2004
[6]	Xu Xiaodong(徐晓东),Chen Yong(陈勇).A pulse cavitating water jet superfine crushing devices:CN,1416959.2003-05-14
[7]	Qian Yupeng(钱玉鹏),Cheng Liang(程亮),Zhu Yingbo(朱瀛波).The development of water-jet comminuting technology and its application in mica comminution[J].Conservation and Utilization of Mineral Resources(矿产保护与利用),2009(6):12-16
[8]	Cui Longlian,An Liqian,Gong Weili,et al.A novel process for preparation of ultra-clean micronized coal by high pressure water jet comminution technique[J].Fuel,2007,86(5/6):750-757
[9]	Guo Chuwen,Dong Lu.Energy consumption in comminution of mica with cavitation abrasive water jet[J].Journal of China University of Mining&Technology,2007,17(2):251-254
[10]	Libor M Hlavá?,Irena M Hlavá?ová,Petr Janda?ka,et al. Comminution of material particles by water jets—influence of the inner shape of the mixing chamber[J].International Journal of Mineral Processing,2010,95(3):25-29
[11]	He Hua(贺华),Wang Xuekui(王学魁),Sun Zhinan(孙之南),et al.Development of new type raw salt comminuting equipment with high-pressure fluid jet[J].Chemical Engineering(China)(化学工程),2009,37(8):50-54
[12]	Wan Jiwei(万继伟),Niu Zhengming(牛争鸣),Niu Zhunong(牛助农).Research of water cushion increased resistance effect of jet impact area during the process of high-speed water jet crushing[J].Chemical Industry and Engineering Progress(化工进展),2012,31(1):30-34
[13]	Wan Yunxia(万云霞),Huang Yong(黄勇),Zhu Ying(朱英).Experiment on the breakup process of free round liquid jet[J].Journal of Aerospace Power(航空动力学报),2008,23(2):208-214
[14]	Faiza Zidouni Kendil,Dana V Danciu,Martin Schmidtke,et al.Flow field assessment under a plunging liquid jet[J].Progress in Nuclear Energy,2012,56:100-110
[15]	Song Jian(宋剑),Li Gensheng(李根生),Hu Yongtang(胡永堂).Numerical simulation of dual jet turbulent flow with combined coaxial swirling and round jet[J].Journal of Hydrodynamics:Ser.A(水动力学研究与进展:A辑),2004,19(5):671-675
[16]	Wan Jiwei(万继伟),Niu Zhengming(牛争鸣),Liao Weili(廖伟丽),et al.Theoretical research on multiphase jet flow characteristic of rear-mixed jet flow crushing and accelerated subarea[J].Journal of Hydrodynamics:Ser.A (水动力学研究与进展:A辑),2012,27(5):621-630
[17]	Dong Zhiyong(董志勇).Jet Mechanics(射流力学)[M].Beijing:Science Press,2005
[18]	Ni Jianjun(倪建军),Liang Qinfeng(梁钦锋),Zhou Zhijie(周志杰),Zhang Yuzhu(张玉柱),Yu Guangsuo(于广锁).Multiphase flow and heat transfer in entrained-flow coal gasification radiant syngas cooler[J].CIESC Journal (化工学报),2009,60(12):2997-3005
[19]	Li Chunli(李春利),Li Jianci(李建慈),Liu Jidong(刘继东),Zhang Le(张仂), Liu Changjiang(刘长江),Li Yanfen(李彦芬).Simulation of two-phase flow field in CTST-8 with VOF method[J].Journal of Chemical Industry and Engineering(China)(化工学报),2007,58(4):881-886
[20]	Liu Z W,Huang C Z,Zhu H T.Study on jet formation and modeling for high pressure abrasive water-jet.[J].Key Engineering Materials,2011,487:468-472

单进口后混式射流粉碎中多相流混合机理及加速特性

Mixing mechanism of multiphase flow and acceleration performance in single inlet rear-mixed jet flow crushing

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献 20

相关文章 2

编辑推荐

Metrics

本文评价

[1]	戚华彪, 徐骥, 宋文立, 葛蔚. 螺旋输送器中颗粒混合过程的模拟[J]. 化工学报, 2018, 69(1): 371-380.
[2]	张立栋，朱明亮，李少华，邓杰文，马金博，王丽伟，王擎. 回转干馏炉内二组元颗粒混合机理及混合度分析[J]. CIESC Journal, 2011, 30(11): 2382-.