Experiments and simulation of a single droplet impacting on cold surfaces

doi:10.11949/j.issn.0438-1157.20160158

CIESC Journal ›› 2016, Vol. 67 ›› Issue (10): 4160-4168.DOI: 10.11949/j.issn.0438-1157.20160158

Previous Articles Next Articles

Experiments and simulation of a single droplet impacting on cold surfaces

XU Qing^1,2, WANG Jin¹, LI Miaomiao¹, LI Zhanyong^1,2

1 College of Mechanical Engineering, Tianjin University of Science and Technology, Tianjin 300222, China;
2 Tianjin Key Laboratory of Integrated Design and On-line Monitoring for Light Industry & Food Machinery and Equipment, Tianjin 300222, China

Received:2016-02-15 Revised:2016-07-20 Online:2016-10-05 Published:2016-10-05
Supported by:
supported by the National Natural Science Foundation of China (31571906, 21506163) and the Natural Science Foundation of Tianjin University of Science and Technology (20130118).

单液滴撞击冷板面的实验和模拟

徐庆^1,2, 王瑾¹, 李苗苗¹, 李占勇^1,2

1 天津科技大学机械工程学院, 天津 300222;
2 天津市轻工与食品工程机械装备集成设计与在线监控重点实验室, 天津 300222

通讯作者: 李占勇
基金资助:
国家自然科学基金项目（31571906,21506163）；天津科技大学自然科学研究基金项目（20130118）。

Abstract

Abstract:

The impact spread and solidification of single distilled water droplet of 3.2 mm in diameter at 293 K on a cold plate with temperature below 273 K was studied by both experiment and simulation. The impact heights (100, 250, 500 mm), cold plate temperatures (253, 268 K), and cold plate inclined angles (0°, 30° and 60°) were assessed for effects on the spreading and solidifying process. The impact process of a pullulan solution droplet at a height of 100 mm on a cold plate at 253 K was simulated and compared to that of a distilled water droplet. The results showed that both impact height and horizontal cold plate temperature played an important role in the droplet spreading process whereas inclined angle of cold plate affected freezing deposition of the droplet. Droplet viscosity affected spreading rate and diameter of freezing deposition. Temperature was not a determinant factor for highly viscose materials. A good alignment between simulation and experimental results indicated that temperature change of the droplet in spreading and freezing process would help to directly explain droplet solidification.

Key words: distilled water droplet, pullulan, cold plate, level set method, solidification modeling

摘要：

用实验和模拟的方法研究了直径为3.2 mm的单个蒸馏水液滴与冷板面（温度低于273 K）撞击铺展和固化过程，分析了撞击高度（100、250、500 mm）、板面温度（253、268 K）、板面倾角（0°、30°和60°）对撞击过程的影响以及液滴在冷板面上冻结过程。并模拟了单个普鲁兰多糖溶液液滴在撞击高度为100 mm、板面温度为253 K的过程。结果表明，撞击高度与板面温度对液滴在水平冷板面的铺展过程起到重要作用，板面倾角会影响液滴撞击倾斜板面时的冷冻沉积。物料的黏度会影响液滴冷冻沉积时的铺展速率及铺展直径，而对于较高黏度物料，温度并不起决定作用。模拟和实验结果吻合较好，反映了液滴铺展冻结过程中的温度变化，有利于直观解释液滴发生冻结的状况。

关键词: 蒸馏水单液滴, 普鲁兰多糖, 冷板面, 水平集方法, 固化模型

CLC Number:

TQ051

XU Qing, WANG Jin, LI Miaomiao, LI Zhanyong. Experiments and simulation of a single droplet impacting on cold surfaces[J]. CIESC Journal, 2016, 67(10): 4160-4168.

徐庆, 王瑾, 李苗苗, 李占勇. 单液滴撞击冷板面的实验和模拟[J]. 化工学报, 2016, 67(10): 4160-4168.

References 20

[1]	徐庆, 耿县如, 李占勇. 喷雾冷冻干燥对颗粒产品形态的影响[J]. 化工进展, 2013, 32(2):270-275. XU Q, GENG X R, LI Z Y. Morphology of particle produced by spray-freeze drying[J]. Chemical Industry and Engineering Progress, 2013, 32(2):270-275.
[2]	朱冬生, 孙纪远, 宋印玺, 等. 喷雾冷却技术综述及纳米流体喷雾应用前景[J]. 化工进展, 2009, 28(3):368-373. ZHU D S, SUN J Y, SONG Y X, et al. Review of spray cooling technique and prospect of spray cooling using nanofluids[J]. Chemical Industry and Engineering Progress, 2009, 28(3):368-373.
[3]	HUANG L Y, LIU Z L, LIU Y M, et al. Effect of contact angle on water droplet freezing process on a cold flat surface[J]. Experimental Thermal and Fluid Science, 2012, 40(7):74-80.
[4]	XU Q, LI Z Y, WANG J, et al. Characteristics of single droplet impact on cold plate surfaces[J]. Drying Technology, 2012, 30(15):1756-1762.
[5]	TABAKOVA S, FEUILLEBOIS F. On the solidification of a supercooled liquid droplet lying on a surface[J]. Journal of Colloid and Interface Science, 2004, 272(1):225-234.
[6]	耿县如, 徐庆, 李占勇, 等. 喷雾冷冻法单个液滴冻结过程模拟[J]. 化工进展, 2012, 31(5):981-986. GENG X R, XU Q, LI Z Y, et al. Numerical simulation of a single droplet freezing process[J]. Chemical Industry and Engineering Progress, 2012, 31(5):981-986.
[7]	GUNJAL P R, RANADE V V, CHAUDHARI R V. Dynamics of drop impact on solid surface:experiments and VOF simulations[J]. AIChE Journal, 2005, 51(1):59-78.
[8]	BUSSMAN M, MOSTAGHIMI J, CHANDRA S. On a three-dimensional volume tracking model of droplet impact[J]. Physics of Fluids, 1999, 11(6):1406-1417.
[9]	STROTOS G, ALEKSIS G, GAVAISES M, et al. Non-dimensionalisation parameters for predicting the cooling effectiveness of droplets impacting on moderate temperature solid surfaces[J]. International Journal of Thermal Sciences, 2011, 50(5):698-711.
[10]	KUMAR A, GHOSH S, DHINDAW B K. Simulation of cooling of liquid Al-33wt.% Cu droplet impinging on a metallic substrate and its experimental validation[J]. Acta Materialia, 2010, 58(1):122-133.
[11]	PASANDIDEH-FARD M, AZIZ S D, CHANDRA S, et al. Cooling effectiveness of a water drop impinging on a hot surface[J]. International Journal of Heat and Fluid Flow, 2001, 22(2):201-210.
[12]	VOLLER V R, PRAKASH C. A fixed grid numerical modelling methodology for convection-diffusion mushy region phase-change problems[J]. International Journal of Heat and Mass Transfer, 1987, 30(8):1709-1719.
[13]	MARIN T L. Solidification of a liquid metal droplet impinging on a cold surface[C]//Proceedings of the COMSOL Users Conference. Trondheim, Norway:COMSOL AS, 2006:1492-1-1492-8.
[14]	王瑾, 李占勇, 徐庆, 等. 单液滴撞击水平冷板面的模拟研究[J]. 天津科技大学学报, 2014, 29(1):36-41. WANG J, LI Z Y, XU Q, et al. Numerical simulation of the impact of single droplet on cold horizontal plate surface[J]. Journal of Tianjin University of Science & Technology, 2014, 29(1):36-41.
[15]	SUSSMAN M, SMEREKA P, OSHER S. A level set approach for computing solutions to incompressible two-phase flow[J]. Journal of Computational Physics, 1994, 114(1):146-159.
[16]	BRAZIER-SMITH P R, LATHAM J. The interaction of falling water drops:coalescence[J]. Proceedings of the Royal Society A, 1972, 326(1566):393-408.
[17]	王晓东, 彭晓峰, 李笃中. 粗糙表面上的移动接触线和动态接触角[J]. 化工学报, 2004, 55(3):402-407. WANG X D, PENG X F, LI D Z. Moving contact line and dynamic contact angle on rough solid surfaces[J]. Journal of Chemical Industry and Engineering(China), 2004, 55(3):402-407.
[18]	姜桂林, 张承武, 管宁, 等. 水在不同接触角微柱群内的流动特征[J]. 化工学报, 2015, 66(5):1704-1709. JIANG G L, ZHANG C W, GUAN N, et al. Flow characteristics of water in hydrophobic micro cylinders group with different contact angles[J]. CIESC Journal, 2015, 66(5):1704-1709.
[19]	ŠIKALO Š, GANI? E N. Phenomena of droplet-surface interactions[J]. Experimental Thermal and Fluid Science, 2006, 31(2):97-110.
[20]	CUI J, CHEN X, WANG F, et al. Study of liquid droplets impact on dry inclined surface[J]. Asia-Pacific Journal of Chemical Engineering, 2009, 4(5):643-648.

Experiments and simulation of a single droplet impacting on cold surfaces

单液滴撞击冷板面的实验和模拟

PDF (PC)

Knowledge

Abstract

Cite this article

share this article

References 20

Related Articles 6

Recommended Articles

Metrics

Comments

[1]	Jiyuan LI, Jinwang LI, Liuwei ZHOU. Heat transfer performance of cold plates with different turbulence structures [J]. CIESC Journal, 2023, 74(4): 1474-1488.
[2]	YIN Yajun, LI Yangdong, TU Zhixin, LI Wen, SHEN Xu, ZHOU Jianxin. Interface capturing method based on Level Set with octree adaptive mesh technology [J]. CIESC Journal, 2016, 67(11): 4732-4741.
[3]	WANG Shenghui, YOU Wei, LI Zengyao. Interface-capturing method on quadtree-based adaptive Cartesian grid [J]. CIESC Journal, 2014, 65(S1): 44-50.
[4]	YANG Binxin, OUYANG Jie, LIU Chuntai, LI Qiang. Simulation of Non-isothermal Injection Molding for a Non-Newtonian Fluid by Level Set Method [J]. , 2010, 18(4): 600-608.
[5]	YANG Zhaochu, DONG Tao, BI Qincheng, ZHANG Yulong. Interface tracking and numerical simulation of micro-bubble controlled growth in micro restrained space [J]. CIESC Journal, 2007, 58(11): 2770-2775.
[6]	LIULiang, JINPing, CHENGMing, ZHANGGuoliang, ZHANGFengbao. 5-Fluorouracil-loaded Self-assembled pH-sensitive Nanoparticles as Novel Drug Carrier for Treatment of Malignant Tumors [J]. , 2006, 14(3): 377-382.