两相流在扁平T型管中压降特性的实验研究

doi:10.11949/j.issn.0438-1157.20181171

化工学报 ›› 2018, Vol. 69 ›› Issue (S2): 174-179.DOI: 10.11949/j.issn.0438-1157.20181171

两相流在扁平T型管中压降特性的实验研究

徐肖肖, 陈龙, 肖久旻, 刘朝

重庆大学能源与动力工程学院, 低品位能源利用技术及系统教育部重点实验室, 重庆 400030

收稿日期:2018-10-09 修回日期:2018-10-19 出版日期:2018-12-31 发布日期:2018-12-31
基金资助:
国家自然科学基金项目（51776020）；重庆市博士后科研项目（Xm2017045）。

Experimental study on pressure drop characteristic of two-phase flow in reduced tee junction with flat tube

XU Xiaoxiao, CHEN Long, XIAO Jiumin, LIU Chao

Key Laboratory of Low-grade Energy Utilization Technologies and Systems, College of Energy and Power Engineering, Chongqing University, Chongqing 400030, China

Received:2018-10-09 Revised:2018-10-19 Online:2018-12-31 Published:2018-12-31
Supported by:
supported by the National Natural Science Foundation of China (51776020) and Chongqing Postdoctoral Scientific Research Foundation (Xm2017045).

摘要/Abstract

摘要：

两相流在普通T型管中的压降特性已经得到充分研究，但是鲜有文献关注侧管为扁平管的T型管（扁平T型管）中的压降特性。以R134a作为工质，对水平放置扁平T型管进行了压降特性的实验研究。结果表明，现有的微通道摩擦压降经验关联式不能够准确预测两相流在微通道扁平管的摩擦压降。通过实验数据的拟合，得到了干度范围为0.01～0.45，流量范围为0.7～3 g/s的分层流在微通道扁平管中的摩擦压降经验关联式，并对Chisholm模型中气液两相相互作用系数C进行修改，使其能够预测主管进口流量在1.1～5.3 g/s，进口干度在0.03～0.26，流量分离比在0.1～0.8时的分层流从集管流入微通道扁平管时的不可逆压降。

Abstract:

The pressure drop characteristic of two-phase flow in normal T-junction has been fully investigated. However, few articles focus on the pressure drop characteristics of the reduced T-junction with flat tube. In this paper, R134a were used as the work medium, and the experimental study on the pressure drop characteristics was carried out at the T-junction placed horizontally. Experimental results show that the existing pressure drop empirical correlations of microchannel were not able to predict the two-phase flow in microchannel flat tube frictional pressure drop accurately. Through fitting experimental data, the empirical correlation of frictional pressure drop for stratified flow with quality range of 0.01-0.45 and flow range of 0.7-3 g/s in microchannel flat tube is obtained, and the gas-liquid interaction coefficient C in Chisholm model was modified to predict the irreversible pressure drop of stratified flow with flow range of 1.1-5.3 g/s, quality range of 0.03-0.26 and separation ratio is 0.1-0.8 from header to flat tube.

中图分类号:

TQ028.8

徐肖肖, 陈龙, 肖久旻, 刘朝. 两相流在扁平T型管中压降特性的实验研究[J]. 化工学报, 2018, 69(S2): 174-179.

XU Xiaoxiao, CHEN Long, XIAO Jiumin, LIU Chao. Experimental study on pressure drop characteristic of two-phase flow in reduced tee junction with flat tube[J]. CIESC Journal, 2018, 69(S2): 174-179.

参考文献 33

[1]	KIM N H, BYUN H W, SIM Y S.Upward branching of two-phase refrigerant in a parallel flow minichannel heat exchanger[J].Experimental Thermal & Fluid Science, 2013, 51(11):189-203.
[2]	舒朝晖, 李丛来, 陈焕新.扁管结构对平行流冷凝器制冷剂侧性能的影响[J].化工学报,2008,59(S2):129-133.SHU Z H, LI C L, CHEN H X.Flat tube structure on performance of refrigerant-side of parallel flow condenser[J].Journal of Chemical Industry and Engineering (China), 2008, 59(S2):129-133.
[3]	刘巍, 朱春玲.分流板结构对微通道平行流蒸发器性能的影响[J].化工学报, 2012, 63(3):761-766.LIU W, ZHU C L.Effects of deflector structure on performance of micro-channel evaporator with parallel flow[J].CIESC Journal, 2012, 63(3):761-766.
[4]	SAEED M, KIM M H.Header design approaches for mini-channel heat sinks using analytical and numerical methods[J].Applied Ther-mal Engineering, 2017, 110:1500-1510.
[5]	鲁红亮, 陶红歌, 胡云鹏, 等.平行流换热器中热流体分布均匀性的研究进展[J].制冷学报, 2010, 31(6):39-45.LU H L, TAO H G, HU Y P, et al. State-of-the-art of thermo-fluid uniform distribution in microchannel heat exchanger[J].Journal of Refrigeration, 2010, 31(6):39-45.
[6]	何奎, 汪双凤, 黄间珍.气液两相流在微小T型三通中的相分配特性[J].化工学报, 2011, 62(1):92-96.HE K, WANG S F, HUANG J Z.Phase split characteristic of two-phase flow through a micro-T-junction[J].CIESC Journal, 2011, 62(1):92-96.
[7]	徐肖肖,肖久旻,陈龙,等.平行流换热器两相流分配模型的建立与验证[J].化工学报, 2018, 69(5):1938-1945.XU X X, XIAO J M, CHEN L, et al.Establishment and verification of a two-phase flow distribution model in a parallel flow heat exchanger[J].CIESC Journal, 2018, 69(5):1938-1945.
[8]	李夔宁, 吴小波, 尹亚领.平行流蒸发器内气液两相流分配均匀性实验研究[J].热能动力工程, 2009, 24(6):759-765.LI K N, WU X B, YIN Y L.Experimental study on the distribution uniformity of gas-liquid two-phase flow in parallel flow evaporator[J].Journal of Engineering for Thermal Energy and Power, 2009, 24(6):759-765.
[9]	VIST S, PETTERSEN J.Two-phase flow distribution in compact heat exchanger manifolds[J].Experimental Thermal & Fluid Science, 2004, 28(2):209-215.
[10]	KIM J S, IM Y B, KIM J H, et al.Two-phase flow distribution in a compact heat exchanger header[C]//ASME 2003, International Conference on Microchannels and Minichannels.2003:513-518.
[11]	KIM N H, HAN S P.Distribution of air-water annular flow in a header of a parallel flow heat exchanger[J].International Journal of Heat & Mass Transfer, 2008, 51(5):977-992.
[12]	LEE J K, LEE S Y.Distribution of two-phase annular flow at header-channel junctions[J].Experimental Thermal & Fluid Science, 2002, 28(2):217-222.
[13]	EL-SHABOURY A M F, SOLIMAN H M, SIMS G E.Two-phase flow in a horizontal equal-sided impacting tee junction[J].Interna-tional Journal of Multiphase Flow, 2007, 33(4):411-431.
[14]	JOYCE G, SOLIMAN H M.Pressure drop for two-phase mixtures combining in a tee junction with wavy flow in the combined side[J].Experimental Thermal & Fluid Science, 2016, 70:307-315.
[15]	BALLYK J D, SHOUKRI M, CHAN A M C.Steam-water annular flow in a horizontal dividing T-junction[J].International Journal of Multiphase Flow, 1988, 14(3):265-285.
[16]	BUEL J R, SOLIMANH M, SIMS G E.Two-phase pressure drop and phase distribution of a horizontal tee junction[J].International Journal of Multiphase Flow, 1994, 20(5):819-836.
[17]	SUN T H, JR R T L.A study on single-and two-phase pressure drop in branching conduits[J].Experimental Thermal & Fluid Science, 1988, 1(2):111-125.
[18]	ZOU Y, HRNJAK P S.Single-phase and two-phase flow pressure drop in the vertical header of microchannel heat exchanger[J].International Journal of Refrigeration, 2014, 44(7):12-22.
[19]	MISHIMA K, HIBIKI T.Some characteristics of air-water two-phase flow in small diameter vertical tubes[J].Int.J.Multiphase Flow, 1996, 22:703-712.
[20]	LEE H J, LEE S Y.Pressure drop correlations for two-phase flow within horizontal rectangular channels with small height[J].Int.J.Multiphase Flow, 2001, 27:783-796.
[21]	QU W, MUDAWAR I.Measurement and prediction of pressure drop in two phase micro-channel heat sinks[J].Int.J.Heat Mass Transfer, 2003, 46:2737-2753.
[22]	YUE J, CHEN G, YUAN Q.Pressure drops of single and two-phase flows through T-type microchannel mixers[J].Chem.Eng.J., 2004, 102:11-24.
[23]	PAMITRAN A S, CHOI K, OH J T, et al.Two-phase pressure drop during CO2 vaporization in horizontal smooth minichannels[J].Int.J.Refrig., 2008, 311:375-1383.
[24]	ZHANG M, WEBB R L.Correlation of two-phase friction for refrigerants in small-diameter tubes[J].Experimental Thermal & Fluid Science, 2001, 25(3):131-139.
[25]	MULLER-STEINHAGEN H, HECK K.A simple friction pressure drop correlation for two-phase flow in pipes[J].Chemical Enginee-ring & Processing Process Intensification, 1986, 20(6):297-308.
[26]	TRAN T N, CHYU M C, WAMBSGANSS M W, et al.Two-phase pressure drop of refrigerants during flow boiling in small channels:an experimental investigation and correlation development[J].International Journal of Multiphase Flow, 2000, 26(11):1739-1754.
[27]	KIM N H, BYUNH W.Effect of inlet configuration on upward branching of two-phase refrigerant in a parallel flow heat exchanger[J].International Journal of Refrigeration, 2013, 36(3):1062-1077.
[28]	KIM N H, LEE E J, BYUN H W.Improvement of two-phase refrigerant distribution in a parallel flow minichannel heat exchanger using insertion devices[J].Applied Thermal Engineering, 2013, 59(1/2):116-130.
[29]	KULKARNI T, BULLARD C W, CHO K.Header design tradeoffs in microchannel evaporators[J].Applied Thermal Engineering, 2004, 24(5):759-776.
[30]	KLINE S J.The purposes of uncertainty analysis[J].Journal of Fluids Engineering, 1985, 107(2):153-160.
[31]	CHISHOLM D.A theoretical basis for the Lockhart-Martinelli correlation for two-phase flow[J].International Journal of Heat & Mass Transfer, 1967, 10(12):1767-1778.
[32]	LEE P S, GARIMELLA S V.Experimental investigation of heat transfer in microchannels[C]//ASME 2003 Heat Transfer Summer Conference.2003:391-397.
[33]	KAWAHARA A, SADATOMI M, NEI K, et al.Experimental study on bubble velocity, void fraction and pressure drop for gas-liquid two-phase flow in a circular microchannel[J].International Journal of Heat & Fluid Flow, 2009, 30(5):831-841.

两相流在扁平T型管中压降特性的实验研究

Experimental study on pressure drop characteristic of two-phase flow in reduced tee junction with flat tube

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献 33

相关文章 15

编辑推荐

Metrics

本文评价

[1]	刘羊九, 韩吉田, 王云山, 任天健. 直接接触式膜蒸馏用于处理含盐溶液的实验研究[J]. 化工学报, 2018, 69(S2): 246-251.
[2]	白茹真, 贾辉, 张诚, 王捷, 张宏伟. 基于FBG传感的正渗透膜界面剪切力变化特性[J]. 化工学报, 2018, 69(12): 5120-5129.
[3]	费兆阳, 李磊, 成超, 楼家伟, 汤吉海, 陈献, 崔咪芬, 乔旭. 铈锆复合氧化物催化HCl氧化中相互作用机制[J]. 化工学报, 2018, 69(12): 5081-5089.
[4]	徐令君, QI Yang, 王淑娟. [Bmim][BF₄]/MEA混合水溶液吸收CO₂的吸收性能与液液分相机理[J]. 化工学报, 2018, 69(12): 5112-5119.
[5]	张继宗, 常厚春, 常建民, 龙金星, 李雪辉. 生物油淀粉胶黏剂固化特性研究[J]. 化工学报, 2018, 69(12): 5309-5315.
[6]	杨颖, 曲冬蕾, 李平, 于建国. 低浓度煤层气吸附浓缩技术研究与发展[J]. 化工学报, 2018, 69(11): 4518-4529.
[7]	曹晓畅, 王志, 乔志华, 王纪孝, 许振良. 一步法制备含氨基化合物的非对称CO₂分离膜[J]. 化工学报, 2018, 69(11): 4778-4787.
[8]	高佳明, 王明, 马晓华, 许振良. 烧结温度对TiO₂/不锈钢中空纤维复合膜结构和性能的影响[J]. 化工学报, 2018, 69(11): 4879-4886.
[9]	水恒心, 潘冯弘康, 金田, 胡军, 刘洪来. 双功能yolk-shell钴@钴氮碳掺杂氧电极催化剂[J]. 化工学报, 2018, 69(11): 4702-4712.
[10]	孙雪飞, 高勇强, 赵颂, 张文, 王志, 王晓琳. 胍基聚合物接枝改性制备抗菌抗污染超滤膜[J]. 化工学报, 2018, 69(11): 4869-4878.
[11]	李阳, 杜乐, 高若梅, 吴偲, 龚亚辉. 微通道中原位分散技术可控制备氧化铜纳米流体及复合薄膜前体[J]. 化工学报, 2018, 69(11): 4918-4928.
[12]	孙洪伟, 于雪, 李维维, 祁国平, 马娟, 吕心涛, 吕慧. 游离氨抑制Nitrobacter活性动力学试验[J]. 化工学报, 2018, 69(10): 4386-4393.
[13]	卢艳军, 胡艳军, 余帆, 于文静. 基于Py-GC/MS的污泥含碳、氧官能团热解演化过程研究[J]. 化工学报, 2018, 69(10): 4378-4385.
[14]	贾晓霞, 王丽, 元宁, 杨江峰, 李晋平. 二价铬/钼/镍空配位MOFs的CH₄/N₂吸附分离研究[J]. 化工学报, 2018, 69(9): 3896-3904.
[15]	许中煌, 雷萍萍, 洪昱斌, 丁马太, 何旭敏, 蓝伟光. 氧化石墨烯/碱式硫酸铝掺杂聚醚砜/聚酰胺复合纳滤膜的制备及其性能[J]. 化工学报, 2018, 69(9): 4066-4074.