隔壁塔内半圆填料层中壁流与返混特性研究

doi:10.11949/0438-1157.20190881

摘要/Abstract

摘要：

在填料塔三参数壁流模型的基础上，提出了应用于隔壁塔半圆型填料层的壁流模型。通过实验对模型参数进行了估计。模型计算值与实验值吻合较好。在内径为580 mm、高2800 mm的半圆冷模塔内，常温常压下以空气-水为介质，测取了散堆填料的壁流曲线，分析了气液速率变化对壁流的影响。以氯化钠溶液为示踪剂，通过脉冲注入扰动响应技术获得停留时间分布曲线。发现气液速率变化均对停留时间分布产生不同程度影响。同时比较了同一填料层高度塔壁区和整体区的平均停留时间，在壁流充分发展阶段，塔壁区的平均停留时间明显小于整体区。从另一方面量化了壁流效应的影响。应用线性回归得到单相流和气液逆流时计算Pe_d的关联式。对于新型填料及塔内件的开发、改进隔壁塔的设计方法，从而实现安全有效放大具有参考意义。

关键词: 隔壁塔, 散堆填料, 壁流, 停留时间, 返混

Abstract:

Based on the three-parameter wall flow model of the packed tower, a wall flow model applied to the semi-circular filler layer of the dividing wall tower is proposed. Refer to experimental data, the model parameters were estimated. The results agree well with the theoretical value. A set of semicircular cold test system with a diameter of 580 mm and a height of 2800 mm was built, and the effect of gas and liquid rate change on the wall flow was analyzed. The residence time distribution(RTD) curves were obtained by pulse injection stimulus-response technique. It is found that the RTD is affected by the change of gas and liquid rate. The influence of wall flow effect is quantified by the average residence time comparison between wall section and bulk section, the results show that the average residence time of wall section was smaller than that of bulk section at the wall flow full development stage. Such data are essential for design and optimization of dividing wall column distillation processes. Correlation of Pe_d is calculated by liner regression. This experiment has reference significance for the development of new packings, inner parts and the improvement of the design method of DWC to achieve safe, reliable and effective amplification.

Key words: dividing wall column, random packing, wall flow, residence time, backmixing

中图分类号:

TQ 028.8

李春利, 李景玉, 张明霞. 隔壁塔内半圆填料层中壁流与返混特性研究[J]. 化工学报, 2020, 71(4): 1460-1468.

Chunli LI, Jingyu LI, Mingxia ZHANG. Research on wall flow and backmixing in semi-circular packing layer of dividing wall column[J]. CIESC Journal, 2020, 71(4): 1460-1468.

图/表 8

参考文献 31

1	Isoz M, Haidl J. CFD analysis of gas flow through corrugated sheet structured packing: effects of packing geometry[J]. Industrial & Engineering Chemistry Research, 2018, 57(34): 11785-11796.
2	李洪, 孟莹, 李鑫钢, 等. 蒸馏过程强化技术研究进展[J]. 化工进展, 2018, 37(4): 1212-1228.
	Li H, Meng Y, Li X G, et al. State-of-the-arts review of the research process for distillation process intensification technology[J]. Chemical Industry and Engineering Progress, 2018, 37(4): 1212-1228.
3	任海伦, 安登超, 朱桃月, 等. 精馏技术研究进展与工业应用[J]. 化工进展, 2016, 35(6): 1606-1626.
	Ren H L, An D C, Zhu T Y, et al. Distillation technology research progress and industrial application[J]. Chemical Industry and Engineering Progress, 2016, 35(6): 1606-1626.
4	李军, 王纯正, 马占华, 等. 隔壁塔用于苯、甲苯、二甲苯分离的控制[J]. 化工进展, 2013, 32(4): 757-762.
	Li J, Wang C Z, Ma Z H, et al. Control of the DWC for separating the mixture of benzene, toluene, xylene[J]. Chemical Industry and Engineering Progress, 2013, 32(4): 757-762.
5	王洪海, 王宝正, 李春利, 等. 垂直双隔板隔壁塔分离四组分的模拟优化和实验研究[J]. 化工学报, 2018, 69(7): 253-261.
	Wang H H, Wang B Z, Li C L, et al. Optimization and experimental study of vertical double wall dividing-wall column for separating a quaternary system[J]. CIESC Journal, 2018, 69(7): 253-261.
6	李春利, 彭飞, 谢江维. 热模隔板塔分离三组分混合物的模拟与控制研究[J]. 现代化工, 2018, 38(1): 183-187.
	Li C L, Peng F, Xie J W, et al. Simulation and control on separation of three-component mixtures by hot modelled dividing wall column[J]. Modern Chemical Industry, 2018, 38(1): 183-187.
7	Ling H, Luyben W L. Temperature control of the BTX divided-wall column[J]. Industrial & Engineering Chemistry Research, 2010, 49(1): 189-203.
8	李建清, 王二强. 确定隔板塔中多定态解的一种有效方法[J]. 计算与应用化学, 2016, 33(7): 779-782.
	Li J Q, Wang E Q. A fast and effective method to find multiple steady states in dividing wall column[J]. Computers and Applied Chemistry, 2016, 33(7): 779-782.
9	方静, 相宁, 李晓春, 等. Kaibel隔壁塔用于四组分精馏的模拟优化和实验研究[J]. 化工进展, 2018, 37(5): 19-27.
	Fang J, Xiang N, Li X C, et al. Optimization and experimental study of Kaibel dividing-wall column for separating a quaternary system[J]. Chemical Industry and Engineering Progress, 2018, 37(5): 19-27.
10	Hu Y Q, Fang J, Li C L. Simulation optimization and experimental study of cross-wall adiabatic dividing wall column used to separate hexane-heptane-octane system[J]. China Petroleum Processing and Petrochemical Technology, 2015, 17(1): 108-116.
11	刘汝佳, 管惟中, 张耀昌, 等. 考虑压力分布特性的隔板精馏塔动态建模[J]. 山东化工, 2018, 47(5): 136-139.
	Liu R J, Guan W Z, Zhang Y C, et al. Dynamic modeling of dividing wall column considering its pressure distribution characteristics[J]. Shandong Chemical Industry, 2018, 47(5): 136-139.
12	Wang Y, Du S, Zhu H G, et al. CFD simulation of hydraulics of dividing wall sieve trays[J]. Advanced Materials Research, 2012, 476/477/478: 1345-1350.
13	Rodríguez-Ángeles M A, Gómez-Castro F I, Segovia-Hernández J G, et al. Mechanical design and hydraulic analysis of sieve trays in dividing wall columns[J]. Computer Aided Chemical Engineering, 2014, 33:1375-1380.
14	Templeman J J, Porter K E. Experimental determinations of wall flow in packed columns[J]. Chemical Engineering Science, 1965, 20(12): 1139-1140.
15	唐忠利, 刘春江, 陈江波, 等. 从浓度分布评价填料塔性能[J]. 化工学报, 2004, 55(5): 810-814.
	Tang Z L, Liu C J, Chen J B, et al. Evaluation of packed tower performance by analyzing distillation composition profile[J]. Journal of Chemical Industry and Engineering（China）, 2004, 55(5): 810-814.
16	张志炳, 卞克建, 丁龙福. 波纹型规整填料的壁流边界[J]. 南京大学学报(自然科学), 1996, 32(4): 585-590.
	Zhang Z B, Bian K J, Ding L F. Wall flow boundary of corrugated structured packings[J]. Journal of Nanjing University(Natural Science), 1996, 32(4): 585-590.
17	刘伯潭, 朱学军, 余国琮. 大型波纹规整填料塔二维返混特性实验测量与模拟[J]. 天津大学学报, 2012, 45(9): 775-778.
	Liu B T, Zhu X J, Yu G C. Experimental measurement and simulation of two dimensional dispersion in commerical scale column containing corrugated structure packing[J]. Journal of Tianjin University, 2012, 45(9): 775-778.
18	张泽廷, 余国琮. 用随机过程模拟填料塔液体的流动分布[J]. 化工学报, 1988，39(2): 162-169.
	Zhang Z T, Yu G C. Stochastic simulation of liquid flow distribution in packed column[J]. Journal of Chemical Industry and Engineering（China）, 1988，39(2): 162-169.
19	宋宝东, 高瑞昶, 李锡源, 等. 测试填料塔中液体分布性能的新方法[J]. 天津大学学报, 1999, 32(3): 354-357.
	Song B D, Gao R C, Li X Y, et al. New measurement method for studying liquid flow distribution in packed columns[J]. Journal of Tianjin University, 1999, 32(3): 354-357.
20	裘俊红, 陈国标, 计建炳. 波纹板规整填料塔液体分布[J]. 化工学报, 2003, 54(5): 646-652.
	Qiu J H, Chen G B, Ji J B. Liquid distribution in corrugated sheet structured packed column[J]. Journal of Chemical Industry and Engineering（China）, 2003, 54(5): 646-652.
21	张会书, 袁希钢, Ali K M. 规整填料内液体分布的实验研究进展[J]. 化工进展, 2015, 34(8): 2932-2939.
	Zhang H S, Yuan X G, Ali K M. Research progress of liquid distribution in structured packing[J]. Chemical Industry and Engineering Progress, 2015, 34(8): 2932-2939.
22	岳强, 李斌斌, 韩洋洋, 等. 摇摆状态下的填料塔液体分布性能研究[J]. 当代化工, 2019, 48(1): 217-219.
	Yue Q, Li B B, Han Y Y, et al. Research on liquid distribution performance of packed tower under swing state[J]. Contemporary Chemical Industry, 2019, 48(1): 217-219.
23	张志炳, 卞克建, 丁龙福, 等. 填料塔壁流的一个新模型[J]. 南京大学学报(自然科学), 1996, 32(2): 236-241.
	Zhang Z B, Bian K J, Ding L F, et al. A new model of wall flow for a packed column[J]. Journal of Nanjing University(Natural Science), 1996, 32(2): 236-241.
24	张志炳, 余国琮. 规整填料塔的壁流研究[J]. 化学工程, 1996, 24(2): 7-13.
	Zhang Z B, Yu G C. Wall flow in a packed column with structured packings[J]. Chemical Engineering(China), 1996, 24(2): 7-13.
25	陆锡满. 新型高效均流填料塔的应用机理研究[D]. 成都: 西南石油大学, 2010.
	Lu X M. Study on application mechanism of a new type efficient symmetrical-flow packed tower[D]. Chengdu: Southwest Petroleum University, 2010.
26	张志炳, Higginbotham P, Porter K E, 等. 规整填料塔的壁流对分离特性的影响[J]. 高校化学工程学报, 1996, 10(4): 411-414.
	Zhang Z B, Higginbotham P, Porter K E, et al. Effect of wall flow in a packed column with structured packings on separation characteristics[J]. Journal of Chemical Engineering of Chinese Universities, 1996, 10(4): 411-414.
27	王承学.化学反应工程[M]. 北京: 化学工业出版社, 2015: 65.
	Wang C X. Chemical Reaction Engineering[M]. Beijing: Chemical Industry Press, 2015:65.
28	李金明. 新型规整填料的开发及其流体力学行为的研究[D]. 天津: 天津大学, 2016.
	Li J M. Research on hydraulic performance of new developed structured packings[D]. Tianjin: Tianjin University, 2016.
29	王琨, 张鹏, 冯立, 等. 填料塔内流体轴向返混系数的确定[J]. 化工科技, 2004, 12(6): 10-13.
	Wang K, Zhang P, Feng L, et al. The evaluation of the fluid axial backmixing coefficient in a packed column[J]. Science & Technology in Chemical Industry, 2004, 12(6): 10-13.
30	李敬楠, 黄哲庆, 项文雨, 等. 高通量催化精馏填料的停留时间分布研究[J]. 化学工程, 2015, 43(4): 15-20.
	Li J N, Huang Z Q, Xiang W Y, et al. Residence time distribution of high-capacity catalytic distillation structured packing[J]. Chemical Engineering(China), 2015, 43(4): 15-20.
31	陈运文, 杨卓如, 陈焕钦, 等. 填料塔内液相轴向返混研究[J]. 高校化学工程学报, 1990, 4(4): 352-358.
	Chen Y W, Yang Z R, Chen H Q, et al. Study on liquid axial dispersion in packed tower[J]. Journal of Chemical Engineering of Chinese Universities, 1990, 4(4): 352-358.

[1]	文兆伦, 李沛睿, 张忠林, 杜晓, 侯起旺, 刘叶刚, 郝晓刚, 官国清. 基于自热再生的隔壁塔深冷空分工艺设计及优化[J]. 化工学报, 2023, 74(7): 2988-2998.
[2]	刘鑫, 潘阳, 刘公平, 方静, 李春利, 李浩. 渗透汽化-隔壁塔精馏耦合初步分离费托合成水的过程研究[J]. 化工学报, 2022, 73(5): 2020-2030.
[3]	赵晶, 李伯耿, 卜志扬, 范宏. 微通道内低黏聚合物流体的停留时间分布研究[J]. 化工学报, 2021, 72(8): 4030-4038.
[4]	胡丹丹, 耿素龙, 曾玺, 王芳, 岳君容, 许光文. 返混对气-固反应特性测试和活化能表征的影响[J]. 化工学报, 2021, 72(3): 1354-1363.
[5]	黄正梁, 王超, 郭燕妮, 杨遥, 孙婧元, 王靖岱, 阳永荣. 基于停留时间分布的缠绕管内二次流研究[J]. 化工学报, 2021, 72(2): 921-927.
[6]	兰斌, 徐骥, 刘志成, 王军武. 连续操作密相流化床颗粒停留时间分布特性模拟放大研究[J]. 化工学报, 2021, 72(1): 521-533.
[7]	王少伦, 杨宏. 高效包埋硝化活性填料硝化特性及应用研究[J]. 化工学报, 2020, 71(5): 2305-2311.
[8]	田凤国, 朱田, 孔德正, 雷鸣. 非均匀布风流化床内大颗粒停留时间特性[J]. 化工学报, 2020, 71(4): 1520-1527.
[9]	梁咏诗, 赵香龙, 秦强, 郭屹, 程易. 气流床气化炉的CPFD数值模拟[J]. 化工学报, 2019, 70(9): 3291-3299.
[10]	杨杰, 祁江羽, 沙勇. 反应精馏隔壁塔制甲缩醛过程模拟与分析[J]. 化工学报, 2019, 70(3): 960-968.
[11]	聂丽君, 李德豪, 何京东, 钟华文, 林培喜, 周如金. ABR-MAP-MBR组合工艺处理高浓度养殖废水研究[J]. 化工学报, 2018, 69(6): 2722-2729.
[12]	邹潺, 王春波, 郭辉, 王贺飞. 燃煤过程中砷的赋存形态及其挥发特性[J]. 化工学报, 2018, 69(4): 1670-1677.
[13]	姚东, 刘明言, 李翔南. 小型气-液-固流化床液相的停留时间分布[J]. 化工学报, 2018, 69(11): 4754-4762.
[14]	王威杰, 雍玉梅, 杨超, 于康. 三维上流式反应器床层流动和返混特性[J]. 化工学报, 2018, 69(1): 381-388.
[15]	周虹佳, 刘飞, 周明, 仲兆祥, 邢卫红. 双膜强化类Fenton工艺处理制浆废水的研究[J]. 化工学报, 2018, 69(1): 490-498.