接触式机械密封端面磨合过程平均膜厚预测

doi:10.3969/j.issn.0438-1157.2013.11.034

化工学报 ›› 2013, Vol. 64 ›› Issue (11): 4137-4142.DOI: 10.3969/j.issn.0438-1157.2013.11.034

接触式机械密封端面磨合过程平均膜厚预测

魏龙¹, 顾伯勤², 张鹏高^1,2, 房桂芳¹

1. 南京化工职业技术学院江苏省流体密封与测控工程技术研究开发中心, 江苏南京 210048;
2. 南京工业大学机械与动力工程学院, 江苏南京 211816

收稿日期:2013-04-01 修回日期:2013-04-19 出版日期:2013-11-05 发布日期:2013-11-05
通讯作者: 魏龙
作者简介:魏龙(1972-),男,博士,教授。
基金资助:
江苏省“六大人才高峰”资助项目(09-D-018,2012-JNHB-017);江苏省高校科研成果产业化推进项目(JH10-55,JHZD2012-14)。

Average film thickness prediction of end faces in contacting mechanical seals in running-in period

WEI Long¹, GU Boqin², ZHANG Penggao^1,2, FANG Guifang¹

1. Fluid Sealing Measure and Control Engineering Research and Development Center of Jiangsu Province, Nanjing College of Chemical Technology, Nanjing 210048, Jiangsu, China;
2. School of Mechanical and Power Engineering, Nanjing University of Technology, Nanjing 211816, Jiangsu, China

Received:2013-04-01 Revised:2013-04-19 Online:2013-11-05 Published:2013-11-05
Supported by:
supported by the Jiangsu Planned Projects for Fostering Talents in Six Scientific Fields(09-D-018,2012-JNHB-017)and the College Industrialization Project of Jiangsu Province(JH10-55,JHZD2012-14).

摘要/Abstract

摘要： 为研究和掌握接触式机械密封端面磨合过程平均膜厚的变化规律,采用分形参数表征磨合过程中密封端面形貌的变化,基于机械密封端面接触分形模型,通过求解端面上微空穴的体积,建立接触式机械密封端面平均膜厚预测模型。对两套B104a-70型机械密封进行磨合试验,试验密封流体为20℃清水,压力为0.5 MPa,转速为2900 r·min^-1,弹簧比压分别为0.15 MPa和0.3 MPa。研究结果表明,随着磨合过程的进行,软质环端面迅速趋于光滑,端面平均膜厚迅速减小;当进入正常磨损阶段后,两套机械密封试件的平均膜厚均稳定在0.295 μm左右。这也表明,密封端面的形貌对平均膜厚的影响较大,而弹簧比压对平均膜厚的影响较小。掌握磨合过程中端面形貌及平均膜厚的变化规律,对接触式机械密封实际运行时端面间工作特性的预测和密封端面设计具有重要意义。

关键词: 机械密封, 端面, 磨合, 平均膜厚, 分形理论

Abstract: In order to study the variation of average film thickness of end faces in contacting mechanical seal in running-in period,the change of surface topography was studied by fractal parameters characterization.Based on the fractal model of mechanical seals,an average film thickness prediction model of end faces in contacting mechanical seal was established by solving the volumes of surface voids of end faces.Running-in tests of two mechanical seals of B104a-70 type were carried out with water as test medium.Test temperature was 20℃,test pressure was 0.5 MPa,rotating speed was 2900 r·min^-1,and spring pressures were 0.15 MPa and 0.3 MPa respectively.The results indicated that the end face of the soft ring tended to be smoothed rapidly and average film thickness decreased rapidly in running-in period.The average film thicknesses of two tested mechanical seals were both about 0.295 μm in the normal wearing stage.Surface topography had significant influence on average film thickness,while spring pressure had little influence on average film thickness.Studying the changes of surface topography and average film thickness has important significance both in the prediction of operating characteristics and in the design of end faces of contacting mechanical seals.

Key words: mechanical seal, end face, running-in, average film thickness, fractal theory

中图分类号:

魏龙, 顾伯勤, 张鹏高, 房桂芳. 接触式机械密封端面磨合过程平均膜厚预测[J]. 化工学报, 2013, 64(11): 4137-4142.

WEI Long, GU Boqin, ZHANG Penggao, FANG Guifang. Average film thickness prediction of end faces in contacting mechanical seals in running-in period[J]. CIESC Journal, 2013, 64(11): 4137-4142.

参考文献 20

[1]	Mayer E.Mechanical Seal[M].Beijing:Chemical Industry Press,1981:80-84
[2]	Gu Yongquan(顾永泉).Practical Technology of Mechanical Seals(机械密封实用技术)[M].Beijing:Mechanical Industrial Press,2001:16-34
[3]	Wei Long(魏龙),Gu Boqin(顾伯勤),Sun Jianjun(孙见君),Feng Xiu(冯秀).Friction mechanism and friction state of end faces of mechanical seals[J].Lubrication Engineering (润滑与密封),2008,33(5):38-41
[4]	Peng X D,Xie Y B,Gu Y Q.Evaluation of mechanical face seals operating with hydrocarbon mixtures[J].Tribology International,2003,36(3):199-204
[5]	Gu Boqin(顾伯勤),Jiang Xiaowen(蒋小文),Sun Jianjun(孙见君),Chen Ye(陈晔).Recent progress on mechanical seal technology[J].Chemical Industry and Engineering Progress (化工进展),2003,22(11):1160-1164
[6]	Wei Long(魏龙),Gu Boqin(顾伯勤),Sun Jianjun(孙见君),Liu Qihe(刘其和),Zhang Guodong(张国东).Face friction property parameter and test technique of mechanical seals[J].Lubrication Engineering(润滑与密封),2006,31(11):198-202
[7]	Peng Xudong(彭旭东),Gu Yongquan(顾永泉).The effects of coning face and fluid inertia on the performance of mechanical face seals at various phase states[J].Journal of the University of Petroleum(石油大学学报),1990,14(3):62-70
[8]	Lebeck A O.Mixed lubrication in mechanical face seals with plain faces[J].Proceedings of the Institution of Mechanical Engineers,1999,213(3):163-175
[9]	Green I.A transient dynamic analysis of mechanical seals including asperity contact and face deformation[J].Tribology Transactions,2002,45(3):284-293
[10]	Xiong S,Salant R F.A dynamic model of a contacting mechanical seal for down-hole tools[J].ASME Journal of Tribology,2003,125(2):391-402
[11]	Ding Xuexing(丁雪兴),Cheng Xiangping(程香平),Li Guodong(李国栋).The numerical simulation for micropolar fluids field of mixing friction in mechanical seal[J].Journal of Petrochemical Universities(石油化工高等学校学报),2008,21(2):63-67
[12]	Wang Leqin(王乐勤),Meng Xiangkai(孟祥恺),Dai Weiping(戴维平),Wu Dazhuan(吴大转).Analysis on sealing performance and fluid-solid coupling model of contacting mechanical seals[J].Journal of Engineering Thermophysics(工程热物理学报),2008,29(11):1864-1866
[13]	Wei Long(魏龙),Chang Xinzhong(常新中),Zhang Penggao(张鹏高).Progress of study on leakage models of contacting mechanical seal end faces[J].Fluid Machinery (流体机械),2012,40(2):36-40
[14]	Majumdar A,Bhushan B.Role of fractal geometry in roughness characterization and contact mechanics of surfaces[J].ASME Journal of Tribology,1990,112(4):205-216
[15]	Wei Long(魏龙),Gu Boqin(顾伯勤),Sun Jianjun(孙见君),Feng Fei(冯飞),Feng Xiu(冯秀).Optimization of surface fractal dimension of friction pair in mechanical seals[J].CIESC Journal (化工学报),2010,61(1):132-136
[16]	Wei Long(魏龙),Gu Boqin(顾伯勤),Zhang Penggao(张鹏高),Fang Guifang(房桂芳).Contact characterizations of end faces in mechanical seals running-in[J].CIESC Journal(化工学报),2012,63(10):3202-3207
[17]	Sun Jianjun(孙见君),Gu Boqin(顾伯勤),Wei Long(魏龙).Leakage model of contacting mechanical seal based on fractal geometry theory[J].Journal of Chemical Industry and Engineering(China)(化工学报),2006,57(7):1626-1631
[18]	Wei Long(魏龙),Gu Boqin(顾伯勤),Feng Xiu(冯秀),Feng Fei(冯飞).Contact fractal model of friction face of mechanical seals[J].CIESC Journal(化工学报),2009,60(10):2543-2548
[19]	Wei Long(魏龙),Gu Boqin(顾伯勤),Liu Qihe (刘其和),Zhang Penggao(张鹏高),Fang Guifang(房桂芳).Correction of contact fractal model for friction faces of mechanical seals[J].CIESC Journal(化工学报),2013,64(5):1723-1729
[20]	Wei Long(魏龙),Gu Boqin(顾伯勤),Sun Jianjun(孙见君).Development of the computer aided testing device for mechanical seals[J].Lubrication Engineering(润滑与密封),2006,31(4):136-139

接触式机械密封端面磨合过程平均膜厚预测

Average film thickness prediction of end faces in contacting mechanical seals in running-in period

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献 20

相关文章 15

编辑推荐

Metrics

本文评价

[1]	江锦波, 彭新, 许文烜, 门日秀, 刘畅, 彭旭东. 泵出型螺旋槽油气密封泄漏特性及参数影响研究[J]. 化工学报, 2023, 74(6): 2538-2554.
[2]	张伟政, 赵吉军, 马学忠, 张琦璇, 庞益祥, 张俊涛. 湍流效应对高速机械密封端面型槽冷却性能影响分析[J]. 化工学报, 2023, 74(3): 1228-1238.
[3]	孟祥铠, 孟令超, 马艺, 江锦波, 彭旭东. 多孔质机械密封耦合润滑模型与密封性能分析[J]. 化工学报, 2022, 73(10): 4576-4584.
[4]	马润梅, 赵祥, 李双喜, 刘兴华, 许灿. 颗粒介质用机械密封热力耦合变形及摩擦磨损研究[J]. 化工学报, 2021, 72(11): 5726-5737.
[5]	葛诚, 孙见君, 苏徐辰, 马晨波, 於秋萍. 扩压式自泵送流体动静压型机械密封性能分析[J]. 化工学报, 2020, 71(5): 2202-2214.
[6]	陈汇龙, 桂铠, 韩婷, 谢晓凤, 陆俊成, 赵斌娟. 上游泵送机械密封润滑膜固体颗粒沉积特性研究[J]. 化工学报, 2020, 71(4): 1712-1722.
[7]	王金红, 陈志, 刘凡, 李建明. 密封环支撑边界条件对机械密封端面变形的影响[J]. 化工学报, 2020, 71(4): 1744-1753.
[8]	陈胡炜, 吉华, 冯东林, 李倩, 陈志. 基于多楔现象的微孔端面机械密封泄漏率分析及孔形设计[J]. 化工学报, 2020, 71(4): 1723-1733.
[9]	马学忠,孟祥铠,张伟政,彭旭东,丁雪兴. 反向瑞利台阶构型液膜空化性能与机械密封空化抽吸效应评价[J]. 化工学报, 2020, 71(12): 5715-5724.
[10]	陈国旗, 孙见君, 孙电锋, 马晨波. 钠冷快堆核主泵用双端面自泵送机械密封性能分析[J]. 化工学报, 2018, 69(8): 3565-3576.
[11]	李双喜, 孙宪栋, 张鹏. 机械密封覆层密封环端面性能分析[J]. 化工学报, 2018, 69(7): 3181-3189.
[12]	孙见君, 陈国旗, 嵇正波, 马晨波. 接触式机械密封界面泄漏机理分析[J]. 化工学报, 2018, 69(4): 1528-1536.
[13]	马学忠, 孟祥铠, 王玉明, 赵文静, 沈明学, 彭旭东. 机械端面密封反向螺旋槽空化效应与泄漏控制机理[J]. 化工学报, 2018, 69(4): 1558-1568.
[14]	嵇正波, 孙见君, 马晨波, 於秋萍, 陆建花. 接触式机械密封界面泄漏机理研究的关键科学问题[J]. 化工学报, 2017, 68(8): 2969-2978.
[15]	陈汇龙, 李同, 任坤腾, 王彬, 赵斌娟. 端面变形对液体动压型机械密封液膜瞬态特性的影响[J]. 化工学报, 2017, 68(4): 1533-1541.