提升管中颗粒局部流率和速度的改进的光纤测量方法

doi:10.11949/j.issn.0438-1157.20160393

摘要/Abstract

摘要：

在一套高约18 m、内径φ100 mm的提升管冷态实验装置上，根据PV-6D光纤探头的测量结果，提出了一种基于整个采样时间计算提升管颗粒局部流率和速度的改进方法，并与文献方法进行了对比。结果表明，两种方法计算的颗粒局部流率和速度相差较大，本文和文献两种方法计算的截面平均颗粒流率与实测值间的最大、最小和平均相对偏差分别为606.9%、241.3%，221.4%、89.5%和388.9%、145.6%，本文方法测量的颗粒流率偏差相对较小。文献方法计算的截面平均颗粒速度均大于操作气速，其气固间滑落速度和滑落系数分别在-1.6～-4.7 m·s^-1及0.56～0.90间变化，与提升管内的气固实际流动存在很大差别；本方法计算的截面平均颗粒速度均小于操作气速，其气固间滑落速度和滑落系数分别在0.6～9.6 m·s^-1及1.11～2.14间变化。反射型光纤探头在测量颗粒浓度时存在的一些问题是导致本文方法测量的颗粒流率、滑落速度和滑落系数偏大的主要原因。此外，根据光纤测量结果，提出了两个计算提升管颗粒循环强度的关系式，可以替代现有的容积法测量。

关键词: 提升管, 颗粒流率, 颗粒速度, 光纤探头, 容积法

Abstract:

A new method was proposed in a cold riser experimental apparatus with height of about 18 m and inner diameter of 100 mm according to the result measured by PV-6D optical fiber to calculate the local particle flux and velocity based on all the sampling time. The new method was compared with the method used in the referring paper. The results showed that the values of local particle flux and velocity calculated by the two methods had a great discrepancy. The maximum, minimum and mean relative errors between the cross-sectional mean particle flux and the measured value calculated by this paper and the referring paper were 606.9%, 241.3%; 221.4%, 89.5% and 388.9%, 145.6%, respectively. Thus, the value of particle flux measured by this paper was relatively low. The cross-sectional mean particle velocity calculated by the referring paper was higher than the operating gas velocity, and the gas-solid slip velocity and slip coefficient respectively varied from -1.6 to -4.7 m·s^-1 and 0.56 to 0.90, respectively, and thus there was a great difference to the actual gas-solid flow in riser. The cross-sectional mean particle velocity calculated by this paper was lower than the operating gas velocity. The gas-solid slip velocity and slip coefficient varied from 0.6 to 9.6 m·s^-1 and 1.11 to 2.14, respectively. There were some problems when using the reflecting optical fiber to measure the particle concentration and it was the main reason that resulted in the higher particle flux, slip velocity and slip coefficient measured by this paper. Furthermore, two fitting functions were come up with to calculate the particle circulation in the riser according to the measuring result by the optical fiber, substituting for the recent volumetric method.

Key words: riser, particle flux, particle velocity, optical fiber probe, volumetric method

中图分类号:

TQ051.11

王芬芬, 鄂承林, 赵爱红, 卢春喜. 提升管中颗粒局部流率和速度的改进的光纤测量方法[J]. 化工学报, 2016, 67(8): 3209-3223.

WANG Fenfen, E Chenglin, ZHAO Aihong, LU Chunxi. Method of optical fiber measurement for local particle flux and velocity in riser[J]. CIESC Journal, 2016, 67(8): 3209-3223.

参考文献 34

[1]	卢春喜,王祝安.催化裂化相关流态化工程[M].北京:中国石化出版社,2002.LU C X,WANG Z A.Fluidized Catalytic Cracking Process[M].Beijing:China Petrochemical Press,2002.
[2]	金涌,祝京旭,汪展文,等.流态化工程原理[M].北京:清华大学出版社,2001.JIN Y,ZHU J X,WANG Z W,et al.Fluidization Engineering Principles[M].Beijing:Tsinghua University Press,2001.
[3]	吴诚,高用祥,高希,等.湍动流化床过渡段中颗粒速度分布的光纤测量与模拟[J].高校化学工程学报,2015,29(1):11-18.WU C,GAO Y X,GAO X,et al.Particle velocity measurements in transition section of turbulent fluidized beds using optical fiber probe and CFD simulation[J].Journal of Chemical Engineering of Chinese Universities,2015,29(1):11-18.
[4]	BASU P,LARGE J F.Circulating Fluidized Bed Technology Ⅱ[M].New York:Pergamon Press,1988:155-164.
[5]	魏飞,陆坊斌,金涌,等.高密度循环流化床中局部颗粒质量流率及操作域的划分[J].化工学报,1996,47(3):346-351.WEI F,LU F B,JIN Y,et al.Mass flux profiles and flow regimes in a high density circulating fluidized bed[J].Journal of Chemical Industry and Engineering (China),1996,47(3):346-351.
[6]	ZHU H Y,ZHU J,LI G Z,et al.Detailed measurements of flow structure inside a dense gas-solids fluidized bed[J].Powder Technol.,2008,180(3):339-349.
[7]	ZHU J X,LI G Z,QIN S Z,et al.Direct measurements of particle velocities in gas-solids suspension flow using a novel five-fiber optical probe[J].Powder Technol.,2001,115(2):184-192.
[8]	郭慕孙,李洪钟.流态化手册[M].北京:化学工业出版社,2008:862-871.KWAUK M,LI H Z.Manual of Fluidization[M].Beijing:Chemical Industry Press,2008:862-871.
[9]	ANDREUX R,GAUTHIER T,CHAOUKI J,et al.New description of fluidization regimes[J].AIChE J.,2005,51(4):1125-1130.
[10]	吴诚,高希,成有为,等.湍动流化床过渡段固含率分布特征的实验及数值模拟[J].化工学报,2013,64(3):858-866.WU C,GAO X,CHENG Y W,et al.Experimental and numerical study of solids concentration distribution intransition section of turbulent fluidized bed[J].CIESC Journal,2013,64(3):858-866.
[11]	漆小波,黄卫星,祝京旭,等.循环流化床提升管中颗粒速度的径向分布及其沿轴向的发展[J].高校化学工程学报,2002,16(2):168-173.QI X B,HUANG W X,ZHU J X,et al.Radial distribution and axial development of particle velocities in a long CFB riser[J].J.Chem.Eng.of Chinese Univ.,2002,16(2):168-173.
[12]	AGUILLON J,SHAKOURZADEH K,CUIGON P.A new method for local solid concentration measurement in circulating fluidized bed[J].Powder Technology,1996,86(3):251-255.
[13]	NIEUWLAND J J,MEIJER R,KUIPERS J A M.Measurements of solids concentration and axial solids velocity in gas-solid two-phase flows[J].Powder Technology,1996,87(2):127-139.
[14]	程长建,黄晋,宋文立,等.光信号互相关法测量循环流化床内颗粒速度的应用研究[J].过程工程学报,2004,4(z1):626-633.CHENG C J,HUANG J,SONG W L,et al.Measurement of particle velocity in CFB by optical cross-correlation method[J].The Chinese Journal of Process Engineering,2004,4(z1):626-633.
[15]	吴诚,高希,成有为,等.光纤法颗粒速度测量信号的标定与校正[J].化学反应工程与工艺,2013,29(2):105-110.WU C,GAO X,CHENG Y W,et al.Calibration and correction of particle velocity signals in optical fiber measurement[J].Chemical Reaction Engineering and Technology,2013,29(2):105-110.
[16]	JOHNSSON H,JOHNSSON F.Measurements of local solids volume-fraction in fluidized bed boilers[J].Powder Technol,2001,115:13-26.
[17]	LIU J Z,GRACE J R,BI X T.Novel multifunctional optical-fiber probe (Ⅰ):Development and validation[J].AIChE J.,2003,49(6):1405-1420.
[18]	LIU J Z,GRACE J R,BI X T.Novel multifunctional optical-fiber probe (Ⅱ):High-density CFB measurements[J].AIChE J.,2003,49(6):1421-1432.
[19]	ELLIS N,BI H T,LIM C J,et al.Influence of probe scale and analysis method on measured hydrodynamics properties of gas-fluidized beds[J].Chem.Eng.Sci.,2004,59:1841-1851.
[20]	XU J,ZHU J X.Experimental study on solids concentration distribution in a two-dimensional circulating fluidized bed[J].Chem.Eng.Sci.,2010,65:5447-5454.
[21]	LI D B,ZHU J,RAY M B,et al.Catalytic reaction in a circulating fluidized bed downer[J].Chem.Eng.Sci.,2011,66:4615-4623.
[22]	MAO Z Q,ZHU J,BARGHI S.Particle velocity and flux distribution in a high solids concentration circulating turbulent fluidized bed[J].Chem.Eng.Sci.,2012,84:437-448.
[23]	MAO Z Q,BARGHI S,ZHU J.Detailed hydrodynamics of high flux gas-solid flow in a circulating turbulent fluidized bed[J].Chem.Eng.J.,2012,209:633-644.
[24]	WANG C X,ZHU J,BARGHI S,et al.Axial and radial development of solids holdup in a high flux/density gas-solids circulating fluidized bed[J].Chem.Eng.Sci.,2014,108:233-243.
[25]	WANG C X,ZHU J,LI C Y,et al.Detailed measurements of particle velocity and solids flux in a high density circulating fluidized bed riser[J].Chem.Eng.Sci.,2014,114:9-20.
[26]	WANG C X,LI C Y,ZHU J.Axial solids flow structure in a high density gas-solids circulating fluidized bed downer[J].Powder Technol.,2015,272:153-164.
[27]	GENG Q,ZHU X L,YANG J,et al.Flow regime identification in a novel circulating-turbulent fluidized bed[J].Chem.Eng.J.,2014,244:493-504.
[28]	鄂承林,卢春喜,高金森,等.气固两相流中颗粒时均速度的测量新方法[J].过程工程学报,2003,3(6):505-511.E C L,LU C X,GAO J S,et al.A new method for the time-averaged velocity in gas-solid two-phase flow[J].The Chinese Journal of Process Engineering,2003,3(6):505-511.
[29]	E C L,LU C X,XU C M,et al.A new method for measurement of local solid flux in gas-solid two-phase flow[J].Chinese Journal of Chemical Engineering,2003,11(6):617-621.
[30]	刘梦溪,卢春喜.单段高料位气-固密相环流汽提器的密度分布[J].石油化工,2001,30(11):850-854.LIU M X,LU C X.Study of a new kind of stripper[J].Petrochemical Technology,2001,30(11):850-854.
[31]	严超宇,卢春喜,王德武,等.组合流化床燃烧器烧焦管内固含率的径向分布研究[J].石化技术与应用,2011,29(2):109-113.YAN C Y,LU C X,WANG D W,et al.Study on radial profiles of solid fraction in coke-burning riser of a compound fluidized bed combustor[J].Petrochemical Technology&Application,2011,29(2):109-113.
[32]	刘伟伟,卢春喜,范怡平,等.气固流化床中双组分混合颗粒的流态化特性[J].化工学报,2008,59(8):1971-1978.LIU W W,LU C X,FAN Y P,et al.Flow behavior of binary mixture particles in gas-solid fluidized beds[J].Journal of Chemical Industry and Engineering (China),2008,59(8):1971-1978.
[33]	范怡平,晁忠喜,卢春喜,等.催化裂化提升管预提升段气固两相流动特性的研究[J].石油炼制与化工,1999,30(9):43-47.FAN Y P,CHAO Z X,LU C X,et al.Study on the gas-solid flow characteristics in the pre-lift zone of FCC riser[J].Petroleum Processing and Petrochemicals,1999,30(9):43-47.
[34]	黄卫星,易彬,杨颖,等.循环床气固提升管中颗粒浓度的轴向分布[J].四川大学学报(工程科学版),2000,32(6):38-41.HUANG W X,YI B,YANG Y,et al.Axial distributions of averaged solids holdups in a 16 m high CFB riser[J].Journal of Sichuan University (Engineering Science Edition),2000,32(6):38-41.