[1] |
WANG Menghan, TU Shunli, YU Chunli.
Optimization strategy of weld line assisted by air traps improvement based on Kriging and NSGA-Ⅱ
[J]. CIESC Journal, 2018, 69(10): 4449-4455.
|
[2] |
JIANG Ben, ZHAI Ming, REN Jianxing, MA Shiheng, SHEN Changyu.
Simulation of fiber erosion on mold during filling process of fiber reinforced plastic injection molding
[J]. CIESC Journal, 2018, 69(7): 3174-3180.
|
[3] |
JIANG Jing, HOU Jianhua, WANG Shiwei, WANG Xiaofeng, SUN Shuhao, ZHANG Kangkang, LI Qian.
Distribution of residual stress in ICM polycarbonate parts with variable curvature
[J]. CIESC Journal, 2017, 68(11): 4367-4375.
|
[4] |
ZHAO Peng, ZHAO Yao, YAN Bo, WANG Xiaoman, LU Shengkun, FU Jianzhong.
Three-dimensional simulation of shear-induced crystallization for polymers during injection molding process
[J]. CIESC Journal, 2017, 68(11): 4359-4366.
|
[5] |
ZHOU Guofa, YANG Peimin, LUO Zhi, JIANG Xiannian.
Numerical simulation on in-mold micro assembly molding process based on viscoelastic thermal fluid structure coupling
[J]. CIESC Journal, 2017, 68(3): 1129-1137.
|
[6] |
WANG Menghan, LIU Xiao, WEI Kang, LI Yanzhao.
Strategy of molding shrinkage control for Bi-layered RHCM based on Kriging and GA
[J]. CIESC Journal, 2017, 68(1): 391-397.
|
[7] |
TONG Ying, ZHU Xiangzhe, GAO He, HE Yandong.
Analysis of 2D flow chaotic mixing at cross section of tri-screw extruder by Lagrangian coherent structure
[J]. CIESC Journal, 2016, 67(10): 4378-4388.
|
[8] |
WANG Xinyu, LI Zheng, GU Junfeng, RUAN Shilun, SHEN Changyu, WANG Xicheng.
Service stress optimization of injection-molded engineering plastic product
[J]. CIESC Journal, 2016, 67(7): 3040-3046.
|
[9] |
WANG Chaofang, HUANG Ming, SHI Xianzhang, SHEN Changyu, ZHAO Zhenfeng.
Thermal convection calculation with variable time step in Hele-Shaw flow simulation of injection molding
[J]. CIESC Journal, 2016, 67(7): 3047-3054.
|
[10] |
HAN Yueyun, CAO Qiling, HUA Quanxian, LU Leiming, TANG Jianwei, LIU Yong.
Synthesis and properties of organic/inorganic superabsorbent resin
[J]. CIESC Journal, 2015, 66(9): 3795-3800.
|
[11] |
GUO Youdan, CHENG Xiaonong.
Flowing deviation behavior of plastic melt during micro injection molding process
[J]. CIESC Journal, 2015, 66(6): 2329-2335.
|
[12] |
WANG Jiajia, WANG Lixia, BIAN Ning, WANG Dongfang, WANG Yongzhen, ZHANG Yang, LI Qian, SHEN Changyu.
Influence of shear history on morphology, microstructure and mechanical properties of micro injection molded parts
[J]. CIESC Journal, 2015, 66(5): 1931-1938.
|
[13] |
ZHAO Junfeng, HUANG Hanxiong.
Phase morphology and barrier performance of water-assisted injection-molded PP/EVOH blend parts
[J]. CIESC Journal, 2015, 66(5): 1964-1969.
|
[14] |
REN Zhong, HUANG Xingyuan, LIU Hesheng, DENG Xiaozhen, HE Jiantao.
Non-isothermal viscoelastic numerical analysis of compressible gas-assisted polymer extrusion molding
[J]. CIESC Journal, 2015, 66(4): 1615-1623.
|
[15] |
WANG Menghan, LI Yanzhao, XIA Zhizi, CHEN Mingliang, YANG Hai.
Processing parameters optimization of rapid heat cycle molding based on Kriging meta-model and genetic algorithm
[J]. CIESC Journal, 2014, 65(12): 5054-5060.
|