颗粒级配对分级机进料管流动特性影响的数值研究

doi:10.3969/j.issn.0438-1157.2012.10.014

化工学报 ›› 2012, Vol. 63 ›› Issue (10): 3101-3111.DOI: 10.3969/j.issn.0438-1157.2012.10.014

颗粒级配对分级机进料管流动特性影响的数值研究

刁雄¹, 李双跃¹, 黄鹏¹, 任曦²

1. 西南科技大学制造科学与工程学院, 四川绵阳 621010;
2. 上海海事大学物流工程学院, 上海 200135

收稿日期:2012-02-28 修回日期:2012-04-16 出版日期:2012-10-05 发布日期:2012-10-05
通讯作者: 李双跃
作者简介:李双跃,刁雄(1986- ),男,硕士研究生。
基金资助:
国家科技支撑计划项目(2011BAA04B04);国家科技计划项目(09C2621502330);西南科技大学研究生创新基金项目(11ycjj30,12ycjj41)。

Effect of particle gradation on flow field of feeding pipe in classifier

DIAO Xiong¹, LI Shuangyue¹, HUANG Peng¹, REN Xihao²

1. School of Manufacturing Science and Engineering, Southwest University of Science and Technology, Mianyang 621010, Sichuan, China;
2. School of Logistic Engineering, Shanghai Maritime University, Shanghai 200135, China

Received:2012-02-28 Revised:2012-04-16 Online:2012-10-05 Published:2012-10-05
Supported by:
supported by the National Key Technology R&D Program(2011BAA04B04),the National Science and Technology Plan(09C2621502330)and the Postgraduate Innovation Fund sponsored by Southwest University of Science and Technology(11ycjj30,12ycjj41).

摘要/Abstract

摘要： 为了分析颗粒级配对超细分级机进料管内流动特性的影响,利用计算流体力学(CFD)方法,对进料管内气固两相流动进行研究。在对计算模型进行验证的基础上,揭示了不同颗粒级配下进出口压差、颗粒浓度分布及颗粒分散等特性。研究表明:进料管进出口压差随着级配中大粒径颗粒含量的增加而增加。当级配中小粒径含量较大时,颗粒浓度分布均匀,颗粒分散性较好,入口风速、喂料浓度、颗粒密度的改变对颗粒量纲1浓度分布及分散性影响较小。对于大粒径含量较大的级配,随着入口风速的增加,量纲1浓度减小,浓度分布不均匀度减小,分散性提高;随着喂料浓度的增加,量纲1浓度分布变化较小,但浓度分布不均匀度增大,颗粒分散性下降;随着物料密度的增加,浓度分布不均匀度减小,颗粒分散性提高。竖直段轴向截面上颗粒量纲1平均浓度的高低分界线为一定值(Z=0.5 m),且与颗粒级配及操作参数的变化无关。

关键词: 超细分级机, 气固两相流, 颗粒级配, 量纲1浓度, 颗粒分散

Abstract: In order to investigate the effect of particle gradation on the flow field of the feeding pipe in a classifier,the computational fluid dynamics method was applied in the study of gas-solids two-phase flow field in the feeding pipe.After the model was verified,the effects of gas velocity,feeding concentration,particle gradation and density on the pressure difference of inlet and outlet,particle concentration distribution and dispersion were analyzed.The results showed that the pressure difference of inlet and outlet increased with increasing large size particle content of gradation.When gradation was with a high content of small size particle,concentration distribution was uniform and particle dispersion was good.The change of gas velocity,feeding concentration and particle density had less influence on particle dimensionless concentration distribution and dispersion.The operation parameters had significant effects on gradation with a high content of large size particle.With the increase of gas velocity,particle dimensionless concentration decreased,concentration non-uniformity decreased,and particle dispersion became better. With the increase of feeding concentration,concentration non-uniformity increased,and particle dispersion became worse.With the increase of particle density,concentration non-uniformity decreased,and particle dispersion became better.The dividing line between high and low dimensionless average concentration in the vertical section of the axial feeding pipe was Z=0.5 m,and it basically unchanged with the change of particle gradation and operation parameters.

Key words: superfine classifier, gas-solid two-phase flow, particle gradation, dimensionless concentration, particle dispersion

中图分类号:

TD454

刁雄, 李双跃, 黄鹏, 任曦. 颗粒级配对分级机进料管流动特性影响的数值研究[J]. 化工学报, 2012, 63(10): 3101-3111.

DIAO Xiong, LI Shuangyue, HUANG Peng, REN Xihao. Effect of particle gradation on flow field of feeding pipe in classifier[J]. CIESC Journal, 2012, 63(10): 3101-3111.

参考文献 22

[1]	Finch J A.Modelling a fish-hook in hydrocyclone selectivity curves[J].Powder Technology,1983,36(1):127-129
[2]	Nageswararao K.A critical analysis of the fish hook effect in hydrocyclone classifiers[J].Chemical Engineering Journal,2000,80(1/2/3):251-256
[3]	Roland N.CFS-HD:a new classifier for fine classification with high efficiency[J].International Journal of Mineral Processing,1996,44/45:723-731
[4]	Roland N.Fine classification with vaned rotors:at the outer edge of the vanes or in the interior vane free area[J].International Journal of Mineral Processing,2004,74:S137-S145
[5]	Liu Jiaxiang(刘家祥),Xu Delong(徐德龙),Zhao Jiangping(赵江平),Xu Yusheng(徐渝笙).The effects of inertia counter-rotating vortices in vortex classifier on particle classification[J].Journal of Xi'an University of Architecture&Technology(西安建筑科技大学学报),1998,30(1):63-66
[6]	Liu Jiaxiang(刘家祥),He Tingshu(何廷树),Xia Jingbo(夏靖波).The effect of frequency spectrum of the eddies of turbulent flow in a turbo classifier on its classification characteristics[J].Journal of Beijing University of Chemical Technology(北京化工大学学报),2003,30(5):48-51
[7]	Du Yanchen(杜妍辰),Wang Shulin(王树林).Particle trajectory in vortex classifier rotor[J].Journal of Chemical Industry and Engineering(China)(化工学报),2005,56(5):823-828
[8]	Chen Haiyan(陈海焱),Chen Wenmei(陈文梅),Xu Hailun(胥海伦).Effects of the operation parameters on the air classifier performance[J].Journal of Sichuan University:Engineering Science Edition(四川大学学报:工程科学版),2006,38(3):87-91
[9]	Li Shuangyue(李双跃),Li Jinchun(李进春),Ren Chaofu(任朝富),Li Hong(李洪).Research on classifying zone of vortex air classer based on rapid classification principle[J].China Powder Science and Technology(中国粉体技术),2009,15:114-119
[10]	Xu Ning,Li Guohua,Huang Zhichu.Numerical simulation of particle motion in turbo classifier[J].China Particuology,2005,3(5):275-278
[11]	Toneva P,Epple P,Breuer M,Peukert W,Wirth K.Grinding in an air classifier mill(Ⅰ):Characterisation of the one-phase flow[J].Powder Technology,2011,211(1):19-27
[12]	Toneva P,Wirth K,Peukert W.Grinding in an air classifier mill(Ⅱ):Characterisation of the two-phase flow[J].Powder Technology,2011, 211(1):28-37
[13]	Guo Lijie,Liu Jiaxiang,Liu Shengzhao,Wang Jinggang.Velocity measurements and flow field characteristic analyses in a turbo air classifier[J].Powder Technology,2007,178(1):10-16
[14]	Huang Qiang(黄强),Yu Yuan(于源),Liu Jiaxiang(刘家祥).Improvement on rotor cage structure of turbo air classifier and numerical simulation of inner flow field[J].CIESC Journal(化工学报),2011,62(5):1264-1268
[15]	Wang Fujun(王福军).Computational Fluid Dynamics Analysis—Theory and Application of CFD Software(计算流体动力学分析——CFD软件原理与应用)[M].Beijing:Tsinghua University Press,2004:124-125
[16]	Morsi S A,Alexander A J.An investigation of particle trajectories in two-phase flow systems[J].Journal of Fluid Mechanics,1972,55(2):193-208
[17]	Ma Aichun(马爱纯),Williams K C,Zhou Jiemin(周孑民),Jones M C.Numerical simulation of some effects on pressure drop predicting in pneumatic transport[J].Journal of Wuhan University of Technology(武汉理工大学学报),2010,32(23):13-16
[18]	Hu Yanhua(胡艳华),Shi Mingxian(时铭显).Numerical simulation and analysis of the gas-phase flow field inside 90°curved square duct with different inclination angle[J].China Petroleum Machinery(石油机械),2007,35(8):9-13
[19]	Taylor A M K P,Whitelaw J H,Yianneskis M.Curved ducts with strong secondary motion:velocity measurements of developing laminar and turbulent flow[J].Journal of Fluids Engineering,1982,104(2):350-359
[20]	Zhou Yun(周云),Chen Xiaoping(陈晓平),Liang Cai(梁财),Meng Qingmin(孟庆敏),Lu Peng(鹿鹏),Pu Wenhao(蒲文灏),Xu Pan(许盼).Effect of mean particle size of pulverized coal on dense phase pneumatic conveying at high pressure[J].Proceeding of the CSEE(中国电机工程学报),2009,29(26):25-29
[21]	Zhou Yun(周云),Chen Xiaoping(陈晓平),Liang Cai(梁财),Meng Qingmin(孟庆敏),Lu Peng(鹿鹏).Resistance characteristics of vertical bend in dense-phase pneumatic conveying of pulverized coal under high pressure[J].CIESC Journal(化工学报),2009,60(3):580-584
[22]	Diao Xiong(刁雄),Li Shuangyue(李双跃),Li Liangchao(李良超),Huang Peng(黄鹏).Numerical simulation on concentration distribution of particles in the feeding pipe of a superfine classifier[J].The Chinese Journal of Process Engineering(过程工程学报),2011,11(5):729-7

颗粒级配对分级机进料管流动特性影响的数值研究

Effect of particle gradation on flow field of feeding pipe in classifier

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献 22

相关文章 15

编辑推荐

Metrics

本文评价

[1]	刘怡琳, 李钰, 余亚雄, 黄哲庆, 周强. 基于重置温度方法的双参数介尺度气固传热模型构建[J]. 化工学报, 2022, 73(6): 2612-2621.
[2]	朱华兴, 王景效, 许建良, 代正华, 刘海峰. 双出口分级气流床气化炉内颗粒速度和浓度分布[J]. 化工学报, 2022, 73(10): 4355-4365.
[3]	林俊杰, 罗坤, 王帅, 胡陈枢, 樊建人. coarse-grained CFD-DEM方法在不同流态流化床中的模拟验证[J]. 化工学报, 2019, 70(5): 1702-1712.
[4]	曹俊雅, 张绅, 张涛, 雍玉梅, 杨超. 上流式反应器气液相间传质特性的实验研究[J]. 化工学报, 2019, 70(10): 3914-3923.
[5]	马乔, 雷福林, 张亚文, 阳绍军, 徐祥, 肖云汉. 不同充气条件下密相输运床返料系统气固流动数值模拟[J]. 化工学报, 2016, 67(12): 4959-4968.
[6]	蔡杰, 钟文琪, 袁竹林. 提升管内细长颗粒流化运动的气固多向耦合模型的构建[J]. 化工学报, 2015, 66(11): 4342-4349.
[7]	王锐, 王建军, 赵艳, 金有海. FCC内置式四旋分离系统内气固两相流场的数值研究[J]. 化工学报, 2014, 65(11): 4262-4270.
[8]	王浩明, 赵海波, 郑楚光. 并列和错列纤维过滤器稳态除尘过程的格子Boltzmann模拟[J]. 化工学报, 2013, 64(5): 1621-1628.
[9]	张彩虹，黄立新，谢普军，游凤，张耀雷. 不同气速下喷动床喷泉区颗粒特性的模拟分析[J]. 化工进展, 2013, 32(04): 763-768.
[10]	张玉春金有海王振波马艺. 超短接触旋流反应器混合腔内气固混合特性的数值模拟[J]. 化工学报, 2012, 63(2): 424-432.
[11]	吕慧刘海峰. 稠密气-固两相旋转射流在气源扰动作用下的流动特征[J]. 化工学报, 2012, 63(2): 393-400.
[12]	刁雄, 李双跃, 黄鹏. 进料方式对超细分级机分级性能的影响[J]. 化工学报, 2012, 63(12): 3818-3825.
[13]	栗晶, 蒋贵丰, 王汉封, 易超, 柳朝晖, 郑楚光. 稀疏气固两相湍流边界层拟序结构变动特性[J]. 化工学报, 2012, 63(11): 3407-3417.
[14]	付飞飞, 许传龙, 王式民. 密相气力输送中气固两相流动特性多源信息分析[J]. 化工学报, 2012, 63(10): 3070-3079.
[15]	岳大鑫，刁雄，李双跃，黄鹏. 基于颗粒轨迹分析的分级机切割粒径计算[J]. 化工进展, 2012, 31(09): 1919-1925.