进料方式对超细分级机分级性能的影响

doi:10.3969/j.issn.0438-1157.2012.12.012

化工学报 ›› 2012, Vol. 63 ›› Issue (12): 3818-3825.DOI: 10.3969/j.issn.0438-1157.2012.12.012

进料方式对超细分级机分级性能的影响

刁雄, 李双跃, 黄鹏

西南科技大学制造科学与工程学院, 四川绵阳 621010

收稿日期:2012-05-09 修回日期:2012-06-18 出版日期:2012-12-05 发布日期:2012-06-27
通讯作者: 李双跃
作者简介:刁雄(1986-),男,硕士研究生。
基金资助:
国家科技支撑计划项目(2011BAA04B04);国家科技计划项目(09C2621502330);西南科技大学研究生创新基金项目(12ycjj41,11ycjj30)。

Effect of feeding type on classification performance of superfine classifier

DIAO Xiong, LI Shuangyue, HUANG Peng

School of Manufacturing Science and Engineering, Southwest University of Science and Technology, Mianyang 621010, Sichuan, China

Received:2012-05-09 Revised:2012-06-18 Online:2012-12-05 Published:2012-06-27
Supported by:
supported by the National Science and Technology Supporting Plan(2011BAA04B04),the National Science and Technology Plan(09C2621502330)and the Postgraduate Innovation Fund sponsored by Southwest University of Science and Technology(12ycjj41,11ycjj30).

摘要/Abstract

摘要： 采用数值模拟方法对两种不同进料方式的分级机进行了气固两相流研究,分析了内部压降、气相速度、固相浓度分布等特性;对两种进料方式的分级机进行了应用研究,对比分析了上下进料方式下的特征粒径和细粉粒径分布特点。结果表明:采用上进料方式由于增加了机械撒料盘,进出口压差更大,同时转子外沿圆柱面上的切向和径向速度分布更为均匀,有利于减小分级粒径的波动,得到粒径分布窄的细粉;采用上进料方式有利于提高颗粒浓度分布的均匀性,但受转速的影响较大;采用上进料和下进料两种方式均能取得较好的分级效果,分级后细粉粒径小且分布窄,主要集中在1~30 μm,30 μm以下的颗粒含量达到90%以上。研究结果对分级机进料方式的设计和结构优化有一定指导作用。

关键词: 超细分级机, 进料方式, 气固两相流, 速度标准偏差, 浓度不均匀度, 粒径分布

Abstract: The gas-solids two-phase flow in the superfine classifier with two different feeding types was studied by numerical simulation.The pressure difference,air velocity and solids concentration distribution were analyzed.The performance superfine classifier with two feeding types was studied by experiments,and the characteristic particle size and size distribution of fine powder of under and upper feeding type were compared and analyzed.The results showed that compared with the under feeding type,the pressure drop between inlet and outlet of the superfine classifier of the upper feeding type was bigger due to adding the mechanical spreading plate.For the upper feeding type,the tangential and radial velocities of cylindrical surface along the rotor were distributed more uniformly,which helped to reduce the fluctuation of classification size and obtain fine powder with narrow particle size distribution.Particle concentration was distributed uniformly with the upper feeding type,but was affected heavily by rotor speed.According to the experiment,both under feeding and upper feeding types could obtain good classification performance.After classification,the size of fine powder was small,with narrow distribution,mainly in the range of 1-30 μm.The percentage of particle less than 30 μm of fine powder was above 90%.The study results could provide guidance to designing the feeding type and optimizing the geometry of the superfine classifier.

Key words: superfine classifier, feeding type, gas-solids two-phase flow, velocity deviation, concentration non-uniformity, particle size distribution

中图分类号:

TD454

刁雄, 李双跃, 黄鹏. 进料方式对超细分级机分级性能的影响[J]. 化工学报, 2012, 63(12): 3818-3825.

DIAO Xiong, LI Shuangyue, HUANG Peng. Effect of feeding type on classification performance of superfine classifier[J]. CIESC Journal, 2012, 63(12): 3818-3825.

参考文献 17

[1]	Wang Qianpu,Melaaen M C,Silva S D.Investigation and simulation of a cross-flow air classifier[J].Powder Technology,2001,120(3):273-280
[2]	Wang Chengduan(王成端),Chen Haiyan(陈海焱),Chen Wenmei(陈文梅).Analysis of performance parameters of superfine powder wormgear classifier[J].Journal of Sichuan University:Engineering Science Edition(四川大学学报:工程科学版),2000,32(6):46-50
[3]	Wu Yong(伍勇),Shi Guangming(施光明),Fang Shanru(方善如).Investigation for effective separation area of a turbo air classifier[J].Journal of Sichuan University:Engineering Science Edition(四川大学学报:工程科学版),2001,33(3):38-40
[4]	Liu Jiaxiang(刘家祥),He Tingshu(何廷树),Xia Jingbo(夏靖波).Air flow field characteristics analyzing and classification process of the turbo classifier[J].Journal of the Chinese Ceramic Society(硅酸盐学报),2003,31(5):485-489
[5]	Yang Qingliang(杨庆良),Liu Jiaxiang(刘家祥).Analysis of flow field in turbo air classifier and improvement of rotor cage structure[J].Chemical Engineering(China)(化学工程),2010,38(1):79-83
[6]	Guo Lijie,Liu Jiaxiang,Liu Shengzhao,Wang Jinggang. Velocity measurements and flow field characteristic analyses in a turbo air classifier[J].Powder Technology,2007,178(1):10-16
[7]	Toneva P,Epple P,Breuer M,Peukert W,Wirth K. Grinding in an air classifier mill(Ⅰ):Characterisation of the one-phase flow[J].Powder Technology,2011,211(1):19-27
[8]	Toneva P,Wirth K,Peukert W.Grinding in an air classifier mill(Ⅱ):Characterisation of the two-phase flow[J].Powder Technology,2011, 211(1):28-37
[9]	Liu Shengzhao(刘圣照),Liu Jiaxiang(刘家祥),Guo Lijie(郭丽杰),Wang Kuisheng(王奎升).Experimental study on flow fields in a turbo air classifier annular regions[J].Chemical Engineering(China)(化学工程),2007,35(12):55-58
[10]	Liu Shengzhao(刘圣照),Liu Jiaxiang(刘家祥),Feng Yongguo(冯永国),Wang Kuisheng(王奎升).Effect of rotor structure on classification characteristics of turbo air classifier[J].Journal of Chemical Industry and Engineering(China)(化工学报),2007,58(7):1751-1756
[11]	Huang Qiang(黄强),Yu Yuan(于源),Liu Jiaxiang(刘家祥).Improvement on rotor cage structure of turbo air classifier and numerical simulation of inner flow field[J].CIESC Journal(化工学报),2011,62(5):1264-1268
[12]	Du Yanchen(杜妍辰),Wang Shulin(王树林).Particle trajectory in vortex classifier rotor[J].Journal of Chemical Industry and Engineering(China)(化工学报),2005,56(5):823-828
[13]	Tong Cong(童聪),Li Shuangyue(李双跃),Qi Haijun(綦海军),Ren Chaofu(任朝富).Analysis and optimization of blade parameters in vertical milling classifier[J].The Chinese Journal of Process Engineering(过程工程学报),2012,12(1):14-18
[14]	Li Jinchun(李进春),Li Shuangyue(李双跃),Ren Chaofu(任朝富),Li Hong(李洪).Numerical simulation and experimentation on L-shape guide vane of vortex classifier[J].Chemical Industry and Engineering Progress(化工进展),2008,27(12):1959-1963
[15]	Yang Xiaohong(杨晓红),Yin Mingde(尹明德).Analysis and study of relevant structures to operating performances of classifier[J].Mining & Processing Equipment(矿山机械),2009,37(1):97-100
[16]	Liu Jiaxiang(刘家祥),Xu Delong(徐德龙),Luo Yongqin(罗永勤),Chen Bingchen(陈炳辰).Experimental study on spreading plate of turbo air classifier[J].Cement(水泥),1998(2):16-19
[17]	Diao Xiong(刁雄),Li Shuangyue(李双跃),Li Liangchao(李良超),Huang Peng(黄鹏).Numerical simulation on concentration distribution of particles in the feeding pipe of a superfine classifier[J].The Chinese Journal of Process Engineering(过程工程学报),2011,11(5):729-735

进料方式对超细分级机分级性能的影响

Effect of feeding type on classification performance of superfine classifier

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献 17

相关文章 15

编辑推荐

Metrics

本文评价

[1]	杨越, 张丹, 郑巨淦, 涂茂萍, 杨庆忠. NaCl水溶液喷射闪蒸-掺混蒸发的实验研究[J]. 化工学报, 2023, 74(8): 3279-3291.
[2]	刘怡琳, 李钰, 余亚雄, 黄哲庆, 周强. 基于重置温度方法的双参数介尺度气固传热模型构建[J]. 化工学报, 2022, 73(6): 2612-2621.
[3]	侯晓松, 刘晨星, 任爱玲, 郭斌, 郭渊明. 超声雾化/表面活性剂强化吸收耦合生物洗涤净化甲苯废气[J]. 化工学报, 2022, 73(10): 4692-4706.
[4]	朱华兴, 王景效, 许建良, 代正华, 刘海峰. 双出口分级气流床气化炉内颗粒速度和浓度分布[J]. 化工学报, 2022, 73(10): 4355-4365.
[5]	陈怡沁, 许于, 周静红, 隋志军, 周兴贵. 锂离子电池异构建模及内部传质机理探究：粒径分布的影响[J]. 化工学报, 2021, 72(2): 1078-1088.
[6]	刘作华, 王闯, 孙伟, 陶长元, 王运东. 弹性搅拌桨强化液-液两相混沌混合及液滴分散特性的研究[J]. 化工学报, 2020, 71(10): 4611-4620.
[7]	牛照程, 张丹, 王辉辉, 王珍珍, 邓才智. 有限截面通道内喷雾顺流掺混动力学特征的实验研究[J]. 化工学报, 2019, 70(S2): 117-122.
[8]	赵京, 张玉锋, 魏小林, 李腾, 宾峰. 高碱煤燃烧过程中亚微米颗粒物PM₁的生成特性[J]. 化工学报, 2019, 70(8): 3113-3120.
[9]	林俊杰, 罗坤, 王帅, 胡陈枢, 樊建人. coarse-grained CFD-DEM方法在不同流态流化床中的模拟验证[J]. 化工学报, 2019, 70(5): 1702-1712.
[10]	孙占朋, 孙国刚, 独岩. 进料位置与风速对旋风分级器颗粒分级效果的影响[J]. 化工学报, 2018, 69(4): 1324-1331.
[11]	袁雪梅, 邓仕槐, 杨悦锁, 杨新瑶. 纳米银在饱和多孔介质含水层中迁移主控机理和影响特征[J]. 化工学报, 2017, 68(11): 4154-4160.
[12]	赵志锋, 杜谦, 董鹤鸣, 苏利鹏, 赵广播, 吕东辉, 王敏, 高建民, 郭馨, 徐力, 赵来福. 湿法脱硫装置对燃煤锅炉PM_2.5排放特征的影响[J]. 化工学报, 2017, 68(11): 4261-4271.
[13]	宿程远, 李伟光, 黄智, 陈孟林. 活性艳蓝经多相类芬顿预处理前后对厌氧污泥性能的影响[J]. 化工学报, 2016, 67(4): 1512-1519.
[14]	马乔, 雷福林, 张亚文, 阳绍军, 徐祥, 肖云汉. 不同充气条件下密相输运床返料系统气固流动数值模拟[J]. 化工学报, 2016, 67(12): 4959-4968.
[15]	赵志锋, 杜谦, 赵广播, 高建民, 董鹤鸣, 曹阳, 韩强, 苏利鹏, 苑鹏飞. 燃煤电厂煤粉炉及CFB锅炉PM_2.5产生及排放特性的现场实验研究[J]. 化工学报, 2015, 66(3): 1163-1170.