化工学报 ›› 2013, Vol. 64 ›› Issue (8): 2745-2751.DOI: 10.3969/j.issn.0438-1157.2013.08.006

• 流体力学与传递现象 • 上一篇    下一篇

液滴撞击不同浸润性壁面动态过程的数值模拟

梁超1,2, 王宏1,2, 朱恂1,2, 陈蓉1,2, 丁玉栋1,2, 廖强1,2   

  1. 1. 重庆大学低品位能源利用及系统教育部重点实验室, 重庆 400030;
    2. 重庆大学工程热物理研究所, 重庆 400030
  • 收稿日期:2012-12-26 修回日期:2013-02-26 出版日期:2013-08-05 发布日期:2013-08-05
  • 通讯作者: 朱恂
  • 作者简介:梁超(1987- ),女,硕士研究生。
  • 基金资助:

    国家重点基础研究发展计划项目(2012CB720403);国家自然科学基金项目(50906102,51106188);重庆市自然科学基金项目(CSTC2011jjA90015);教育部留学回国人员科研启动基金项目(教外司留[2010]1561号)。

Numerical simulation of droplet impact on surfaces with different wettabilities

LIANG Chao1,2, WANG Hong1,2, ZHU Xun1,2, CHEN Rong1,2, DING Yudong1,2, LIAO Qiang1,2   

  1. 1. Key Laboratory of Low-grade Energy Utilization Technologies and Systems, Ministry of Education, Chongqing University, Chongqing 400030, China;
    2. Institute of Engineering Thermophysics, Chongqing University, Chongqing 400030, China
  • Received:2012-12-26 Revised:2013-02-26 Online:2013-08-05 Published:2013-08-05
  • Supported by:

    supported by the National Basic Research Program of China(2012CB720403),the National Natural Science Foundation of China(50906102,51106188)and the Natural Science Foundation of Chongqing(CSTC2011jjA90015).

摘要: 采用VOF方法模拟了液滴以相同速度撞击到接触角分别为63°、90°、118°和160°的固体壁面上的形态演变过程。结果表明:固壁的亲憎水性对液滴撞击表面后形态的演化有较大影响,亲水壁面有利于液滴的铺展,在接触角为90°的壁面上液滴部分反弹,而当接触角为160°时,液滴完全反弹;当三相接触线开始回缩时,中心液体的表层部分在惯性力的作用下继续向铺展的液滴边缘聚集,导致近中心处液膜逐渐减薄至断裂,最终形成边缘较厚的液环;同时,液滴最大铺展系数随壁面接触角的增大而减小,达到最大铺展系数的时间也相应缩短。

关键词: 液滴撞击, 壁面浸润性, 铺展系数, 动态过程

Abstract: Dynamic behavior of an impacting water droplet was simulated with the VOF(volume of fluid)method.Droplet diameter was 2.6 mm and impacting velocity was 0.5 m·s-1.Droplet dynamic behavior on simulated,hydrophilic and hydrophobic surfaces was simulated with an impacting angle of 63?,90?,118癮nd 160?.Simulation results showed reasonably good agreement with the experiment data.Surface wettability seriously affected droplet dynamic behavior.Droplet spread well and then sticked on the hydrophilic surface.On the surface with an impacting angle of 90?,droplet partly rebounded away from the surface.While droplet totally rebounded when impacting on the hydrophobic surface.There was an edge liquid ring for liquid sticking on the droplet edge when contact line draw back.The maximum spreading factor and the time needed to arrive at the maximum spread diameter were reduced with increasing contact angle.

Key words: droplet impact, surface wettability, spreading factor, dynamic process

中图分类号: