机械密封的扭转变形计算方法与影响因素

doi:10.3969/j.issn.0438-1157.2013.10.028

化工学报 ›› 2013, Vol. 64 ›› Issue (10): 3686-3693.DOI: 10.3969/j.issn.0438-1157.2013.10.028

机械密封的扭转变形计算方法与影响因素

许静, 彭旭东, 白少先, 李纪云

浙江工业大学过程装备及其再制造教育部工程研究中心, 浙江杭州 310032

收稿日期:2013-01-30 修回日期:2013-03-25 出版日期:2013-10-05 发布日期:2013-10-05
通讯作者: 彭旭东
作者简介:许静(1986-),博士研究生。
基金资助:
国家自然科学基金项目(51175740,51275473);浙江省自然科学基金杰出青年团队项目(R1090833);教育部博士点基金项目(20103317110002)

Calculation methods of face torsional deformation and related affecting factors for mechanical seal

XU Jing, PENG Xudong, BAI Shaoxian, LI Jiyun

MOE Engineering Research Center of Process Equipment and its Remanufacture, Zhejiang University of Technology, Hangzhou 310032, Zhejiang, China

Received:2013-01-30 Revised:2013-03-25 Online:2013-10-05 Published:2013-10-05
Supported by:
supported by the National Natural Science Foundation of China(51175740,51275473), the Zhejiang Science Fund for Outstanding Youths(R1090833)and the Ph.D.Programs Foundation of Ministry of Education of China(20103317110002).

摘要/Abstract

摘要： 针对机械密封环的典型结构,基于圆环理论,建立了密封环结构受力与变形的分析模型。采用圆环理论解析式和有限元法对密封环扭转变形进行了对比计算,分析了密封环的几何结构形状、几何结构尺寸和辅助密封圈的安放位置等因素对密封环扭转变形的影响规律。结果表明:采用理论解析法替代有限元法的计算方法是可行、有效的;复杂截面密封环的台阶长或宽各小于4 mm时,均可直接忽略台阶对扭转变形的影响;辅助密封圈的安放位置和密封环结构形状对扭转变形量均具有重要影响;密封环尺寸在变化不大的前提下,其对扭转变形影响不大。研究结果完善了高压机械密封的设计理论与方法。

关键词: 机械密封, 密封环结构, 扭转变形, 解析法

Abstract: The structural investigation model was presented based on the circle theory so as to study the influence of different constructions,sizes and positions of secondary sealing ring on torsion deformation of the typical mechanical seal ring.High pressure mechanical seal design theories and methods were discussed. The results showed that the method of analytical calculation instead of the finite element method was feasible and effective.The step on the complex section of sealing ring could be directly ignored when the step size of length or width was smaller than 4 mm.Different constructions and placements of the secondary sealing ring were important factors affecting torsion deformation of mechanical seal ring.A small variation of ring size would not affect torsional deformation.The design theory and method of high pressure mechanical seal were improved.

Key words: mechanical seal, seal ring construction, torsion deformation, analytic method

中图分类号:

TH117.2

许静, 彭旭东, 白少先, 李纪云. 机械密封的扭转变形计算方法与影响因素[J]. 化工学报, 2013, 64(10): 3686-3693.

XU Jing, PENG Xudong, BAI Shaoxian, LI Jiyun. Calculation methods of face torsional deformation and related affecting factors for mechanical seal[J]. CIESC Journal, 2013, 64(10): 3686-3693.

参考文献 15

[1]	Jiao Qingyu(焦庆雨),Sun Bo(孙博),Cui Kejia(崔可嘉),et al.Development and application of HP dry gas seal in China[J].Petroleum Refinery Engineering(炼油技术与工程),2009,38(12):31-33
[2]	Mayer E.Mechanical Seal(机械密封)[M].Beijing:Chemical Industry Press,1981
[3]	Lebeck A O.Principles and Design of Mechanical Face Seals[M].Wiley Interscience Publication,John Wiley and Sons,1991:227-280
[4]	Philip J,Guichelaar M W,Chao W O.Experimental verifications of thermal elastic mechanical seal face deflection by local wear measurements[J].Lubrication Engineering,2000,56(1):26-32
[5]	Gu Yongquan(顾永泉).Mechanical Face Seal(机械端面密封)[M].Shandong:Press of Petroleum University,1994
[6]	Hong Xianzhi(洪先志).Study on face mechanical deformation of mechanical seal[D].Chengdu:Sichuan University,2002
[7]	Peng Xudong(彭旭东),Zhang Yuelin(张岳林),Bai Shaoxian(白少先),et al.Effect of rotational speeds or sealed medium pressures on the optimization value of groove geometric parameters of T-groove dry gas face seal[J].CIESC Journal,2012,63(2):551-559
[8]	Peng Xudong(彭旭东),Feng Xiangzhong(冯向忠),Hu Danmei(胡丹梅),et al.Numerical analysis of deformation of a non-contacting gas lubricated seal[J].Tribology(摩擦学学报),2004,24(6):536-540
[9]	Peng Xudong(彭旭东),Liu Wei(刘伟),Bai Shaoxian(白少先),et al.Effects analysis of thermo-elastic deformation on the performance of hydrostatic mechanical seals in reactor coolant pumps[J].Journal of Mechanical Engineering(机械工程学报),2010,46(23):146-153
[10]	Cai Yongning(蔡永宁),Pan Xiaomei(潘晓梅),Peng Xudong(彭旭东).Numerical analysis of deformation of a laser surface textured mechanical seal[J].Lubrication Engineering(润滑与密封),2007,32(2):81-84
[11]	Wei Long(魏龙),Gu Boqin(顾伯勤),Feng Fei(冯飞),et al.Research on deformation property of end face asperity of contact mechanical seals[J].Journal of Drainage and Irrigation Machinery Engineering(排灌机械工程学报),2010,28(1):78-82
[12]	Li Xiang(李香),Wu Zhaoshan(吴兆山),Yang Bofeng(杨博峰),et al.Study on factors and control method of mechanical seal deformation for high-pressure pumps[J].Hydraulics Pneumatics & Seals(液压气动与密封),2012(6):72-75
[13]	Li Man(李鳗),Yao Liming(姚黎明),Wu Zhaoshan(吴兆山),et al.Study on face deformation of mechanical seal[J].Lubrication Engineering(润滑与密封),2001(5):44-47
[14]	Zhang Jie(张杰),Li Kun(李鲲),Wu Zhaoshan(吴兆山),et al.Study on pressure deformation of mounted carbon seal ring[J].Lubrication Engineering(润滑与密封),2012,37(3):53-58
[15]	Gu Yongquan(顾永泉).Mechanical Seal Practical Technology(机械密封实用技术)[M].Beijing:Mechanical Engineering Press,2009

机械密封的扭转变形计算方法与影响因素

Calculation methods of face torsional deformation and related affecting factors for mechanical seal

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献 15

相关文章 15

编辑推荐

Metrics

本文评价

[1]	张伟政, 赵吉军, 马学忠, 张琦璇, 庞益祥, 张俊涛. 湍流效应对高速机械密封端面型槽冷却性能影响分析[J]. 化工学报, 2023, 74(3): 1228-1238.
[2]	孟祥铠, 孟令超, 马艺, 江锦波, 彭旭东. 多孔质机械密封耦合润滑模型与密封性能分析[J]. 化工学报, 2022, 73(10): 4576-4584.
[3]	马润梅, 赵祥, 李双喜, 刘兴华, 许灿. 颗粒介质用机械密封热力耦合变形及摩擦磨损研究[J]. 化工学报, 2021, 72(11): 5726-5737.
[4]	葛诚, 孙见君, 苏徐辰, 马晨波, 於秋萍. 扩压式自泵送流体动静压型机械密封性能分析[J]. 化工学报, 2020, 71(5): 2202-2214.
[5]	陈胡炜, 吉华, 冯东林, 李倩, 陈志. 基于多楔现象的微孔端面机械密封泄漏率分析及孔形设计[J]. 化工学报, 2020, 71(4): 1723-1733.
[6]	王金红, 陈志, 刘凡, 李建明. 密封环支撑边界条件对机械密封端面变形的影响[J]. 化工学报, 2020, 71(4): 1744-1753.
[7]	陈汇龙, 桂铠, 韩婷, 谢晓凤, 陆俊成, 赵斌娟. 上游泵送机械密封润滑膜固体颗粒沉积特性研究[J]. 化工学报, 2020, 71(4): 1712-1722.
[8]	马学忠,孟祥铠,张伟政,彭旭东,丁雪兴. 反向瑞利台阶构型液膜空化性能与机械密封空化抽吸效应评价[J]. 化工学报, 2020, 71(12): 5715-5724.
[9]	陈国旗, 孙见君, 孙电锋, 马晨波. 钠冷快堆核主泵用双端面自泵送机械密封性能分析[J]. 化工学报, 2018, 69(8): 3565-3576.
[10]	李双喜, 孙宪栋, 张鹏. 机械密封覆层密封环端面性能分析[J]. 化工学报, 2018, 69(7): 3181-3189.
[11]	马学忠, 孟祥铠, 王玉明, 赵文静, 沈明学, 彭旭东. 机械端面密封反向螺旋槽空化效应与泄漏控制机理[J]. 化工学报, 2018, 69(4): 1558-1568.
[12]	孙见君, 陈国旗, 嵇正波, 马晨波. 接触式机械密封界面泄漏机理分析[J]. 化工学报, 2018, 69(4): 1528-1536.
[13]	嵇正波, 孙见君, 马晨波, 於秋萍, 陆建花. 接触式机械密封界面泄漏机理研究的关键科学问题[J]. 化工学报, 2017, 68(8): 2969-2978.
[14]	陈汇龙, 李同, 任坤腾, 王彬, 赵斌娟. 端面变形对液体动压型机械密封液膜瞬态特性的影响[J]. 化工学报, 2017, 68(4): 1533-1541.
[15]	李振涛, 郝木明, 杨文静, 韩婕, 任宝杰. 波度和锥度对液体润滑机械密封空化特性影响[J]. 化工学报, 2016, 67(5): 2005-2014.