文丘里式气泡发生器内气泡破碎机制分析

doi:10.11949/j.issn.0438-1157.20171279

化工学报 ›› 2018, Vol. 69 ›› Issue (6): 2439-2445.DOI: 10.11949/j.issn.0438-1157.20171279

文丘里式气泡发生器内气泡破碎机制分析

邵梓一^1,2, 张海燕^1,2, 孙立成³, 莫政宇³, 杜敏³

1. 中国科学院工程热物理研究所, 北京 100190;
2. 中国科学院大学工程科学学院, 北京 100049;
3. 四川大学水利水电学院, 水力学与山区河流开发保护国家重点实验室, 四川成都 610065

收稿日期:2017-09-19 修回日期:2017-12-18 出版日期:2018-06-05 发布日期:2018-06-05
通讯作者: 张海燕
基金资助:
国家自然科学基金项目（51376052，51506099，51606130）。

Bubble breakup mechanism in Venturi-type bubble generator

SHAO Ziyi^1,2, ZHANG Haiyan^1,2, SUN Licheng³, MO Zhengyu³, DU Min³

1. Institute of Engineering Thermophysics, Chinese Academy of Sciences, Beijing 100190, China;
2. School of Engineering Science, University of Chinese Academy of Sciences, Beijing 100049, China;
3. State Key Laboratory of Hydraulics and Mountain River Engineering, College of Water Resource & Hydropower, Sichuan University, Chengdu 610065, Sichuan, China

Received:2017-09-19 Revised:2017-12-18 Online:2018-06-05 Published:2018-06-05
Supported by:
supported by the National Natural Science Foundation of China (51376052, 51506099, 51606130).

摘要/Abstract

摘要：

作为一种高效、安全的气泡发生装置，文丘里式气泡发生器在工业、化工等过程有广泛的应用，但对其内部气泡破碎过程和作用机制相关研究较少。前期研究发现，较大气泡进入文丘里管扩张段后会发生迅速减速，并对气泡碎化过程产生极大影响。基于大涡模拟方法，对文丘里式气泡发生器内的流动过程进行了数值模拟，发现在扩张段近壁面存在明显的涡流区，涡流区前端与上游来流发生强烈的碰撞，造成进入此区域的流体发生迅速减速，使得涡流区与主流交汇区附近静压急速增大；当此区域存在运动的气泡时，激增的压力梯度力以及附加质量力导致气泡运动速度迅速减小，并与周边流体形成了更强的相互作用；高流速条件下，会使气泡发生严重变形、甚至破碎。

关键词: 文丘里式气泡发生器, 减速过程, 数值分析, 涡流场, 静压

Abstract:

As efficient and safe equipment, Venturi-type bubble generators have wide application in general and chemical industry. There are few researches about process and mechanism of bubble breakup inside generators. Previous studies showed that large bubbles were rapidly decelerated after entered diverging section of a Venturi-type bubble generator, which was probably critical to bubble breakup process. In this paper, large-eddy simulation on flow in a Venturi-type bubble generator showed existence of an obvious vortex region near wall of the diverging section. A strong collision between front of the vortex region and fluid from upstream fast decelerated fluid upon entering the region and significantly increased static pressure near confluence of vortex region and mainstream. When a bubble was moving through the region, it would be greatly decelerated by a surge in pressure gradient force and mass-added force, which intensified interaction with ambient fluid. Under a high liquid velocity condition, the bubble could be severely deformed and even broken..

Key words: Venturi-type bubble generator, deceleration process, numerical analysis, vortex field, static pressure

中图分类号:

TQ021.1

邵梓一, 张海燕, 孙立成, 莫政宇, 杜敏. 文丘里式气泡发生器内气泡破碎机制分析[J]. 化工学报, 2018, 69(6): 2439-2445.

SHAO Ziyi, ZHANG Haiyan, SUN Licheng, MO Zhengyu, DU Min. Bubble breakup mechanism in Venturi-type bubble generator[J]. CIESC Journal, 2018, 69(6): 2439-2445.

参考文献 30

[1]	ROBERTSON. MSRE design and operation report I[R]. Atomic Energy Commission, 1965:205-243.
[2]	徐志强, 皇甫京华, 曾鸣, 等. 射流浮选柱气泡发生器及其充气性能的研究[J]. 中国矿业大学学报, 2003, 32(6):19-23. XU Z Q, HUANGFU J H, ZENG M, et al. Research on bubble generator of jet flotation column and its aerating performance[J]. Journal of China University of Mining & Technology, 2003, 32(6):19-23.
[3]	QUIROZ-PÉREZ E, VÁZQUEZ-ROMÁN R, LESSO-ARROYO R, et al. An approach to evaluate Venturi-device effects on gas wells production[J]. Journal of Petroleum Science and Engineering, 2014, 116:8-18.
[4]	邓超, 杨丽, 陈海军, 等. 微纳米气泡发生装置及其应用的研究进展[J]. 石油化工, 2014, 43(10):1206-1213. DENG C, YANG L, CHEN H J, et al. Progresses in research and application of micro-nano bubble generating device[J]. Petrochemical Technology, 2014, 43(10):1206-1213.
[5]	莫政宇, 杜敏, 邵梓一, 等. 文丘里式气泡发生器内气泡输运过程研究[J]. 原子能科学技术, 2016, 50(6):1034-1039. MO Z Y, DU M, SHAO Z Y, et al. Investigation of bubble transportation in Venturi-type bubble generator[J]. Atomic Energy Science and Technology, 2016, 50(6):1034-1039.
[6]	SOUBIRAN J, SHERWOOD J D. Bubble motion in a potential flow within a Venturi[J]. International Journal of Multiphase Flow, 2000, 26(11):1771-1796.
[7]	严润刚, 潘良明, 何辉, 等. 多微通道内两相流动阻力特性及气泡行为[J]. 化工学报, 2017, 68(S1):66-70. YAN R G, PAN L M, HE H, et al. Characteristics of two-phase flow resistance and bubble behavior in microchannels[J]. CIESC Journal, 2017, 68(S1):66-70.
[8]	FUJIWARA A, TAKAGI S, MATSUMOTO Y. Bubble breakup phenomena in a Venturi tube[C]//ASME/JSME 2007 Fluids Engineering Division Summer Meeting. San Diego, USA, 2007:FEDSM2007-37243.
[9]	RZEHAK R, KREPPER E. Closure models for turbulent bubbly flows:a CFD study[J]. Nuclear Engineering and Design, 2013, 265:701-711.
[10]	GASTON M J, REIZES J A, EVANS G M. Modelling of bubble dynamics in a Venturi flow with a potential flow method[J]. Chemical Engineering Science, 2001, 56:6427-6435.
[11]	顾汉洋, 郭烈锦. 垂直圆管内湍流泡状流的数值研究[J]. 化工学报, 2004, 55(4):563-568. GU H Y, GUO L J. Numerical simulation of turbulent bubble flow in vertical pipe[J]. Journal of Chemical Industry and Engineering(China), 2004, 55(4):563-568.
[12]	周吉, 朱恂, 丁玉栋, 等. 液体通流微小槽道内气泡动力学行为模拟[J]. 化工学报, 2011, 62(10):2740-2746. ZHOU J, ZHU X, DING Y D, et al. Numerical simulation of gas bubble emerging from pore into liquid flow micro-channel[J]. CIESC Journal, 2011, 62(10):2740-2746.
[13]	RODIO M G, CONGEDO P M. Robust analysis of cavitating flows in the Venturi tube[J]. European Journal of Mechanics, B/Fluids, 2014, 44:88-99.
[14]	王玲玲. 大涡模拟理论及其应用综述[J]. 河海大学学报(自然科学版), 2004, 32(3):261-265. WANG L L. Large eddy simulation theory and its application[J]. Journal of Hohai University (Natural Sciences), 2004, 32(3):261-265.
[15]	周力行. 离散型两相流动的大涡模拟[J]. 中国科学:技术科学, 2014, 44:162-171. ZHOU L X. Large-eddy simulation of dispersed two-phase flows[J]. Sci. Sin. Tech., 2014, 44:162-171.
[16]	张鹏. 竖直圆管内气泡运动的大涡模拟研究[J]. 原子能科学技术, 2012, 46:225-230. ZHANG P. Large eddy simulation of bubbly flow in vertical tube[J]. Atomic Energy Science and Technology, 2012, 46:225-230.
[17]	DHOTRE M T, NICENO B, SMITH B L. Large eddy simulation of a bubble column using dynamic sub-grid scale model[J]. Chemical Engineering Journal, 2008, 136(2):337-348.
[18]	LUCAS D, KREPPER E, PRASSER H M. Development of co-current air-water flow in a vertical pipe[J]. International Journal of Multiphase Flow, 2005, 31(12):1304-1328.
[19]	LUCAS D, KREPPER E, PRASSER H M. Use of models for lift, wall and turbulent dispersion forces acting on bubbles for poly-disperse flows[J]. Chemical Engineering Science, 2007, 62(15):4146-4157.
[20]	LUCAS D, KREPPER E, RZEHAK R, et al. CFD models for poly dispersed bubbly flows[J]. International Journal of Multiphase Flow, 2007, 29:1148-1159.
[21]	ISHⅡ M, ZUBER N. Drag coefficient and relative velocity in bubbly, droplet or particulate flows[J]. AIChE Journal, 1979, 25(5):843-855.
[22]	BASSET A B. A Treatise on Hydrodynamics[M]. Cambridge:Dover Publications Inc., 1888.
[23]	BOUSSINESQ J. On a simple mode of flow of infiltration water tables with a horizontal stream bed, with a vertical ledge all around, when a part of this ledge is taken away from the surface to the bottom[J]. Comptes Rendus Hebdomadaires Des Séances De Lacademie Des Scienses, 1903, 137(2):5-11.
[24]	MEI R. Velocity fidelity of flow tracer particles[J]. Experiments in Fluids, 1996, 22(1):1-13.
[25]	ANTON D. On the role of the history force for inertial particles in turbulence[J]. Journal of Fluid Mechanics, 2015, 782:567-593.
[26]	BIESHEUVEL A, SPOELSTRA S. The added mass coefficient of a dispersion of spherical gas bubbles in liquid[J]. International Journal of Multiphase Flow, 1989, 15(6):911-924.
[27]	潘良明, 张文志, 陈德奇, 等. 附加惯性力对气泡破裂的影响[J]. 核动力工程, 2011, 32(4):37-41. PAN L M, ZHANG W Z, CHEN D Q, et al. Effects of additional inertia force on bubble breakup[J]. Nuclear Power Engineering, 2011, 32(4):37-41.
[28]	CAI X L, WALLIS G B. Potential flow around a row of spheres in a circular tube[J]. Physics of Fluids A-Fluid Dynamics, 1992, 4(5):904-912.
[29]	CLIMENT E. Simulation d'ecoulements induits par des bulles dans un liquide initialement aurepos[J]. C. R. Acad. Sci., 1997, 324:91-98.
[30]	HUNT F. Review of the problems of modeling disperse two-phase flows[J]. Multiphase Science and Technology, 1997, 8:595-643.

文丘里式气泡发生器内气泡破碎机制分析

Bubble breakup mechanism in Venturi-type bubble generator

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献 30

相关文章 15

编辑推荐

Metrics

本文评价

[1]	邵远哲, 赵忠盖, 刘飞. 基于共同趋势模型的非平稳过程质量相关故障检测方法[J]. 化工学报, 2023, 74(6): 2522-2537.
[2]	李正涛, 袁志杰, 贺高红, 姜晓滨. 疏水界面上的NaCl液滴蒸发过程内环流调控机制研究[J]. 化工学报, 2023, 74(5): 1904-1913.
[3]	魏琳, 郭剑, 廖梓豪, Dafalla Ahmed Mohmed, 蒋方明. 空气流量对空冷燃料电池电堆性能的影响研究[J]. 化工学报, 2022, 73(7): 3222-3231.
[4]	徐祖良, 汪宇昊, 赵辉, 周骛, 蔡小舒, 刘海峰. 同轴四通道喷嘴气流式雾化特性影响因素研究[J]. 化工学报, 2022, 73(2): 604-611.
[5]	张志敏, 丁雪兴, 张兰霞, 力宁, 司佳鑫. 浮环密封端面分形磨损预估模型及数值分析[J]. 化工学报, 2022, 73(12): 5526-5536.
[6]	龚海峰, 罗鑫, 彭烨, 余保, 杨阳, 张浩华. 工业废油异构旋流三相分离装置去固结构及优化[J]. 化工学报, 2022, 73(11): 5025-5038.
[7]	孟祥铠, 孟令超, 马艺, 江锦波, 彭旭东. 多孔质机械密封耦合润滑模型与密封性能分析[J]. 化工学报, 2022, 73(10): 4576-4584.
[8]	陈尔健, 代彦军. 使用NH₃-LiNO₃工质对的增压型回热吸收循环性能分析[J]. 化工学报, 2021, 72(S1): 445-452.
[9]	王彦红, 陆英楠, 李素芬, 东明. U形圆管中超临界压力RP-3航空煤油换热数值研究[J]. 化工学报, 2021, 72(9): 4639-4648.
[10]	马玖辰, 易飞羽, 张秋丽, 王宇. 富水型热储层深井套管式换热器传热特性研究[J]. 化工学报, 2021, 72(8): 4134-4145.
[11]	刘庭江, 王静娴, 于洋, 赵一鸣, 胡大鹏. 壁面脉动传热对气波制冷性能影响研究[J]. 化工学报, 2021, 72(8): 4073-4080.
[12]	郭金玉, 李文涛, 李元. 在线压缩KECA的自适应算法在故障检测中的应用[J]. 化工学报, 2021, 72(8): 4227-4238.
[13]	石敦峰, 甘云华, 罗燕来, 江政纬, 周毅. 乙醇浓度和应变率对扩散火焰特性的数值分析[J]. 化工学报, 2021, 72(5): 2801-2809.
[14]	汪恺, 杜文莉, 隆建. 在线自适应波长选择方法及其在汽油调和过程中的应用[J]. 化工学报, 2021, 72(2): 1059-1066.
[15]	蔡本安, 郭民承, 车勋建, 蔡伟华. 多级喷雾闪蒸海水淡化系统性能分析及响应面优化研究[J]. 化工学报, 2021, 72(11): 5573-5581.