CaSO4 fouling characteristics on dimple tube

doi:10.11949/j.issn.0438-1157.20170944

Abstract

Abstract:

A physical model of dimple tube was established. The effects of structure and working conditions on CaSO₄ fouling characteristics were simulated based on standard k-ε equation and SIMPLE algorithm. The results show that dimple arrangement has little effect on the fouling resistance asymptotic value. For the high Reynolds number, the fouling resistance of dimple tube is always smaller than that of smooth tube. For the low Reynolds number, the fouling resistance of the dimple tube with a low height is slightly higher than that of the smooth tube. The height and density of dimple have a remarkable effect on the fouling resistance. The anti-fouling rate of the dimple tube is 1.150 and 0.730, when the dimple height is 0.8 and the dimple density is 5.30, respectively. Furthermore, the anti-fouling rate increases with the increase of the inlet flow rate, and decreases with the increase of the working fluid concentration and the wall temperature.

Key words: dimple tube, CaSO₄ fouling, numerical simulation, deposition, experimental validation

摘要：

建立了丁胞管物理模型，采用标准k-ε方程和SIMPLE算法，研究了丁胞管内CaSO₄流体的污垢特性，分析了结构与运行工况对丁胞管内CaSO₄污垢特性的影响。结果表明，丁胞的顺排叉排对于污垢热阻渐进值影响极小。高Reynolds数时，与光管的污垢热阻相比，丁胞的存在会减小污垢热阻值；而在低Reynolds数时，相对深度较小的丁胞反而会增大污垢热阻值。丁胞的相对深度与丁胞的相对密度对于污垢热阻值均有较大的影响，在丁胞深度为0.8时，丁胞管的抑垢效率为1.150。在丁胞的相对密度为5.30时，其抑垢效率为0.730。丁胞管抑垢率随着进口流速增长而增大，随着工质浓度增长而减小，随着壁面温度的增长而减小。

关键词: 丁胞管, CaSO₄析晶污垢, 数值模拟, 沉积物, 实验验证

CLC Number:

TK172

XU Zhiming, GUO Yuanjie, HAN Zhimin, ZHAO Yu. CaSO₄ fouling characteristics on dimple tube[J]. CIESC Journal, 2018, 69(4): 1341-1348.

徐志明, 郭元杰, 韩志敏, 赵宇. 丁胞型圆管CaSO₄的污垢特性[J]. 化工学报, 2018, 69(4): 1341-1348.

References 31

[1]	BERGLES A E, MANGLIK R M. Current progress and new development in enhanced heat and mass transfer[J]. Journal of Enhanced Heat Transfer, 2013, 20(1):1-15.
[2]	丹宇. 丁胞流道内流动传热的数值模拟研究[D]. 重庆:重庆大学, 2004. DAN Y. Numerical study of convective heat transfer in the dimpled channel[D]. Chongqing:Chongqing University, 2004.
[3]	AFANASYEV V N, Chudnovsky Y P, Leontiev A I. Turbulent flow friction and heat transfer characteristics for spherical cavities on a flat plate[J]. Experimental Thermal and Fluid Science, 1993, 7(1):1-8.
[4]	BURGESS N K, OLIVERIRA M M, LIGRANI P M. Nusselt number behavior on deep dimpled surfaces within a channel[J]. Journal of Heat Transfer, 2003, 125(1):11-18.
[5]	BURGESS N K, LIG R P M. Effects of dimple depth on Nusselt numbers and friction factors for internal cooling in a channel[C]//ASME Turbo Expo:Power for Land, Sea, & Air, 2004:989-998.
[6]	高昂, 陈榴, 戴韧, 等. 丁胞壁面斜向冲击传热特性的试验研究[J]. 能源工程, 2016, (6):6-11. GAO A, CHEN L, DAI R, et al. Experimental study on heat transfer characteristics of oblique impinging on a dimpled surface[J]. Energy Engineering, 2016, (6):6-11.
[7]	刘高文, 张丽, 郭涛. 凹坑强化传热的研究进展回顾[J]. 航空动力学报, 2007, 22(11):1785-1791. LIU G W, ZHANG L, GUO T. Review of heat transfer enhancement for dimpled surface[J]. Journal of Aerospace Power, 2007, 22(11):1785-1791.
[8]	王禹晨, 唐桂华. 新型换热表面硫酸腐蚀特性的数值分析[J]. 化工学报, 2016, 67(S1):76-83. WANG Y C, TANG G H. Numerical predictions of sulfuric acid corrosion on novel heat transfer surfaces[J]. CIESC Journal, 2016, 67(S1):76-83.
[9]	WANG Y C, TANG G H. Acid condensation and heat transfer characteristics on H-type fin surface with bleeding dimples and longitudinal vortex generators[J]. Chines Science Bulletin, 2014, 59(33):4405-4417.
[10]	KIM K, SHIN D. Optimization of a staggered dimpled surface in a cooling channel using kriging model[J]. International Journal of Thermal Sciences, 2008, 47(11):1464-1472.
[11]	LIGRANI P M, MAHMOOD G I, HARRISON J L, et al. Flow structure and local nusselt number variations in a channel with dimples and protrusions on opposite walls[J]. International Journal of Heat & Mass Transfer, 2001,44(23):4413-4425.
[12]	张一龙, 刘坐东, 徐志明. 浮点型涡流发生器CaSO4析晶污垢沉积的模拟研究[J]. 热能动力工程, 2014, 29(6):692-696. ZHANG Y L, LIU Z D, XU Z M. Simulation study of the CaSO4 crystallization foul deposition in a floating point type vortex generator[J]. Journal of Engineering for Thermal Energy and Power, 2014, 29(6):692-696.
[13]	李瑞, 何雅玲, 楚攀. 丁胞型强化换热管的数值模拟[J]. 工程热物理学报, 2008, 29(11):1947-1949. LI R, HE Y L, CHU P. Numerical simulation of dimple tubes for heat transfer enhancement[J]. Journal of Engineering Thermophysics, 2008, 29(11):1947-1949.
[14]	陈清华, 贺志强, 刘娟芳, 等. 丁胞型强化换热管内突起结构对流传热及阻力的数值模拟[J]. 燃烧科学与技术, 2014, 20(1):21-25. CHEN Q H, HE Z Q, LIU J F, et al. Numerical simulation of convection heat transfer and pressure loss for the protrusions in the dimpled tube[J]. Journal of Combustion Science and Technology, 2014, 20(1):21-25.
[15]	李保德, 刘鹏, 郑年本, 等. 丁胞强化传热管内的流动与传热性能研究[J]. 工程热物理学报, 2016, 37(6):1261-1267. LI B D, LIU P, ZHENG N B, et al. Numerical simulation of helically dimpled tubes for convection heat transfer and pressure drop[J]. Journal of Engineering Thermophysics, 2016, 37(6):1261-1267.
[16]	LU Z, YONG H X, DI Z. Numerical investigation on heat transfer performance and flow characteristics in circular tubes with dimpled twisted tapes using Al2O3-water nanofluid[J]. International Journal of Heat and Mass Transfer, 2017, 111:962-981.
[17]	KANG Y K, DONG Y S. Optimization of a staggered dimpled surface in a cooling channel using Kriging model[J]. International Journal of Thermal Science, 2008, 47(8):1464-1472.
[18]	WANG Y, HE Y L, LEI Y G, et al. Heat transfer and hydrodynamics analysis of a novel dimpled tube[J]. Experimental Thermal and Fluid Science, 2010, 34(8):1273-1281.
[19]	CHEN J, MULLER S H, DUFFY G. Heat transfer enhancement in dimpled tubes[J]. Applied Thermal Engineering, 2001, 21(5):535-547.
[20]	钱吉裕, 平丽浩, 徐德好. 丁胞结构强化换热机理的场协同分析[J]. 热科学与技术, 2009, 6(3):214-218. QIAN J Y, PING L H, XU D H. Numerical investigation on mechanism of heat transfer enhancement with fields synergism theory for dimpled surface[J]. Journal of Thermal Science and Technology, 2009, 6(3):214-218.
[21]	MOON S W, LAU S C. Turbulent heat transfer measurements on a wall with concave and cylindrical dimples in a square channel[C]//ASME Turbo Expo:Power for Land, Sea, & Air, 2002:459-467.
[22]	WANG Y, HE Y L, LEI Y G, et al. Heat transfer and friction characteristics for turbulent flow of dimpled tubes[J]. Chemical Engineering and Technology, 2009, 32(6):956-963.
[23]	KONAK A R. A new model for surface reaction controlled growth of crystals form solution[J]. Chemical Engineering Science, 1974, 29(7):1537-1543.
[24]	徐志明, 张一龙, 徐欣. 温度及浓度对析晶污垢沉积特性影响的模拟研究[J]. 中国电机工程学报, 2014, 34(35):6263-6270. XU Z M, ZHANG Y L, XU X. Simulation study on influent of temperature and concentration on crystallization fouling deposition[J]. Proceedings of the CSEE, 2014, 34(35):6263-6270.
[25]	BIRD R B. Transport Phenomena[M]. New York:Wiley, 1960.
[26]	平亚明, 孙奉仲, 高明. 结垢换热面流体流动特性对于污垢热阻的影响研究[J]. 水动力学研究与进展, 2004, 19(4):458-461. PING Y M, SUN F Z, GAO M. Study of the influence of the fluid characteristics on fouling resistance on heat transfer surface[J]. Journal of Hydrodynamics, 2004, 19(4):454-461.
[27]	Brahim F, Augustin W, Bohnet M. Numerical simulation of the fouling process[J]. International Journal of Thermal Sciences, 2003, 42(7):323-334.
[28]	KRAUSE S. Fouling of heat transfer surface by crystallization and sedimentation[J]. International Chemical Engineering, 1993, 33(3):355-401.
[29]	张一龙, 王乐君, 韩志敏, 等. 运行工况对两种强化管内析晶污垢的影响[J]. 东北电力大学学报, 2015, 35(6):50-55. Zhang Y L, Wang L J, Han Z M, et al. Effect of operating conditions on the strengthening tube crystallization fouling[J]. Journal of Northeast Dianli University, 2015, 35(6):50-55.
[30]	刘有昌, 孙晓君. 磁化水抑垢机理的研究[J]. 哈尔滨工业大学学报, 2000, 23(1):86-90. Liu Y C, Sun X j. Restraint of scale formation by magnetized water and its mechanism[J]. Journal of Harbin Institute of Technology, 2000, 23(1):86-90.
[31]	张一龙. 影响换热表面析晶污垢形成因素研究[D]. 北京:华北电力大学, 2015. ZHANG Y L. The influence factor of crystallization fouling formation on the heat exchanger surface[D]. Beijing:North China Electric Power University, 2015.

CaSO₄ fouling characteristics on dimple tube

丁胞型圆管CaSO₄的污垢特性

PDF (PC)

Knowledge

Abstract

Cite this article

share this article

References 31

Related Articles 15

Recommended Articles

Metrics

Comments

[1]	Jiahao SONG, Wen WANG. Study on coupling operation characteristics of Stirling engine and high temperature heat pipe [J]. CIESC Journal, 2023, 74(S1): 287-294.
[2]	Siyu ZHANG, Yonggao YIN, Pengqi JIA, Wei YE. Study on seasonal thermal energy storage characteristics of double U-shaped buried pipe group [J]. CIESC Journal, 2023, 74(S1): 295-301.
[3]	Cheng CHENG, Zhongdi DUAN, Haoran SUN, Haitao HU, Hongxiang XUE. Lattice Boltzmann simulation of surface microstructure effect on crystallization fouling [J]. CIESC Journal, 2023, 74(S1): 74-86.
[4]	Zhanyu YE, He SHAN, Zhenyuan XU. Performance simulation of paper folding-like evaporator for solar evaporation systems [J]. CIESC Journal, 2023, 74(S1): 132-140.
[5]	Yifei ZHANG, Fangchen LIU, Shuangxing ZHANG, Wenjing DU. Performance analysis of printed circuit heat exchanger for supercritical carbon dioxide [J]. CIESC Journal, 2023, 74(S1): 183-190.
[6]	Zhiguo WANG, Meng XUE, Yushuang DONG, Tianzhen ZHANG, Xiaokai QIN, Qiang HAN. Numerical simulation and analysis of geothermal rock mass heat flow coupling based on fracture roughness characterization method [J]. CIESC Journal, 2023, 74(S1): 223-234.
[7]	Song HE, Qiaomai LIU, Guangshuo XIE, Simin WANG, Juan XIAO. Two-phase flow simulation and surrogate-assisted optimization of gas film drag reduction in high-concentration coal-water slurry pipeline [J]. CIESC Journal, 2023, 74(9): 3766-3774.
[8]	Lei XING, Chunyu MIAO, Minghu JIANG, Lixin ZHAO, Xinya LI. Optimal design and performance analysis of downhole micro gas-liquid hydrocyclone [J]. CIESC Journal, 2023, 74(8): 3394-3406.
[9]	Chen HAN, Youmin SITU, Bin ZHU, Jianliang XU, Xiaolei GUO, Haifeng LIU. Study of reaction and flow characteristics in multi-nozzle pulverized coal gasifier with co-processing of wastewater [J]. CIESC Journal, 2023, 74(8): 3266-3278.
[10]	Xiaosong CHENG, Yonggao YIN, Chunwen CHE. Performance comparison of different working pairs on a liquid desiccant dehumidification system with vacuum regeneration [J]. CIESC Journal, 2023, 74(8): 3494-3501.
[11]	Wenzhu LIU, Heming YUN, Baoxue WANG, Mingzhe HU, Chonglong ZHONG. Research on topology optimization of microchannel based on field synergy and entransy dissipation [J]. CIESC Journal, 2023, 74(8): 3329-3341.
[12]	Wenxiang NI, Jing ZHAO, Bo LI, Xiaolin WEI, Dongyin WU, Di LIU, Qiang WANG. Study on waste heat boiler ash deposition characteristics in sensible heat recovery process of converter gas [J]. CIESC Journal, 2023, 74(8): 3485-3493.
[13]	Rui HONG, Baoqiang YUAN, Wenjing DU. Analysis on mechanism of heat transfer deterioration of supercritical carbon dioxide in vertical upward tube [J]. CIESC Journal, 2023, 74(8): 3309-3319.
[14]	Kexin HUANG, Tong LI, Anqi LI, Mei LIN. Mode decomposition of flow field in T-junction with rotating impeller [J]. CIESC Journal, 2023, 74(7): 2848-2857.
[15]	Fangzhe SHI, Yunhua GAN. Numerical simulation of start-up characteristics and heat transfer performance of ultra-thin heat pipe [J]. CIESC Journal, 2023, 74(7): 2814-2823.