氨法烟气脱硫过程中气溶胶颗粒生成特性

doi:10.11949/j.issn.0438-1157.20150528

化工学报 ›› 2015, Vol. 66 ›› Issue (11): 4366-4372.DOI: 10.11949/j.issn.0438-1157.20150528

氨法烟气脱硫过程中气溶胶颗粒生成特性

黄荣廷, 潘丹萍, 盛溢, 杨林军

东南大学能源热转换及其过程测控教育部重点实验室, 江苏南京 210096

收稿日期:2015-04-27 修回日期:2015-06-04 出版日期:2015-11-05 发布日期:2015-11-05
通讯作者: 杨林军
基金资助:
国家自然科学基金项目(21276049);国家高技术研究发展计划项目(2013AA065004);国家重点基础研究发展计划项目(2013CB228505)。

Properties of aerosol formation during wet ammonia-based desulfurization process

HUANG Rongting, PAN Danping, SHENG Yi, YANG Linjun

Key Laboratory of Energy Thermal Conversion and Control of Ministry of Education, Southeast University, Nanjing 210096, Jiangsu, China

Received:2015-04-27 Revised:2015-06-04 Online:2015-11-05 Published:2015-11-05
Supported by:
supported by the National Natural Science Foundation of China (21276049), the National High Technology Research and Development Program of China (2013AA065004) and the National Basic Research Program of China (2013CB228505).

摘要/Abstract

摘要：

利用自行搭建的模拟氨法烟气脱硫实验平台,针对氨法脱硫中脱硫浆液液滴夹带蒸发和非均相反应两种气溶胶生成途径,采用电称低压冲击器(ELPI)、PM_2.5/10采样器、场发射扫描电子显微镜(FESEM)等手段对两种途径下生成的气溶胶浓度、粒度分布以及形貌特征进行了测试分析,实验考察了氨法脱硫工艺参数对两种途径下生成的气溶胶特性的影响。结果表明,氨法脱硫中形成的气溶胶颗粒从数浓度角度而言,主要为亚微米级颗粒,从质量浓度分析,则以微米级及更大颗粒为主;脱硫浆液中挥发逸出的气态NH₃和烟气中水汽、SO₂间的非均相反应是氨法脱硫气溶胶的主要来源,其形成量主要取决于脱硫浆液pH、脱硫塔进口烟温等;其次来自于脱硫液滴的夹带蒸发作用,其形成量主要取决于脱硫浆液浓度、空塔气速等。

关键词: 氨法脱硫, 烟气, 非均相反应, 蒸发夹带, 气溶胶, 生成特性

Abstract:

An ammonia-based wet flue gas desulfurization (WFGD) simulation was built to simulate separately the two different aerosol formation mechanisms in ammonia-based desulfurization process of the inhomogeneous reaction mechanism and the entrainment mechanism. The electrical low pressure impactor (ELPI, Dekati Ltd.) was employed for the online measurement of aerosol concentration in the outlet flue gas after the WFGD scrubber. The pollutant PM sampler was used for aerosol sampling in the flue gas. The samples gathered were then scanned and analyzed by the field emission scanning electron microscope (FESEM). The results showed that the inhomogeneous reaction of NH₃ escaped from desulfurization slurry with the moisture and SO₂ in the flue gas was the dominating one of the two aerosol formation mechanisms in the ammonia-based WFGD, which produced the majority of the aerosols emitted from the scrubber. It was found that the aerosols were consisted mainly of submicron particles if counted in respect of numerical concentration and micron ones in respect of mass concentration. The amount of aerosols produced was depended mainly on the desulfurization solution pH along with the flue gas temperature at the inlet of WFGD, etc. The entrainment mechanism was of the secondary importance in the aerosol formation in the ammonia-based WFGD. The production of the aerosols was mainly related to the desulfurization solution concentration, the empty tower gas velocity, and so forth.

Key words: ammonia-based WFGD, flue gas, heterogeneous reaction, entrainment, aerosol, formation property

中图分类号:

黄荣廷, 潘丹萍, 盛溢, 杨林军. 氨法烟气脱硫过程中气溶胶颗粒生成特性[J]. 化工学报, 2015, 66(11): 4366-4372.

HUANG Rongting, PAN Danping, SHENG Yi, YANG Linjun. Properties of aerosol formation during wet ammonia-based desulfurization process[J]. CIESC Journal, 2015, 66(11): 4366-4372.

参考文献 20

[1]	Xu Changxiang(徐长香), Fu Guoguang(傅国光). Review on ammonia flue gas desulfurization [J]. Electric Power Environmental Protection(电力环境保护), 2005, 21(2): 17-20.
[2]	Liu Deyou(刘德友), Chu Caiquan(褚才全), Xu Changxiang(徐长香), et al. Application of ammonia process of flue gas desulfurization in petrochemical thermoelectricity plant [J]. China Environmental Protection Industry(中国环保产业), 2008, (11): 28-31.
[3]	Zhang Wenwu(张文武), Sha Zhiqiang(沙志强), Zhu Zhongyi(朱忠益), et al. Emission characteristics of aerosol from ammonia-based wet flue gas desulfurization [J]. Thermal Power Generation(热力发电), 2013, 42(9): 32-37, 62.
[4]	Zhang Wenli(张文丽), Xu Dongqun(徐东群). The characteristics and toxic mechanism of fine particle pollution (PM2.5) in air [J]. Environmental Monitoring in China(中国环境监测), 2002, 18(1): 59-63.
[5]	Xu Yingru(徐映如), Wang Danxia(王丹侠), Zhang Jianwen(张建文), et al. General situation for the hazards, control and evaluation standard system of PM10 and PM2.5 [J]. Occupation and Health(职业与健康), 2013, (1): 117-119.
[6]	Schwartz J, Dockery D W, Neas L M. Is daily mortality associated specifically with fine particles? [J]. Journal of the Air & Waste Management Association, 1996, 46(10): 927-939.
[7]	He Boshu(何伯述), Zheng Xianyu(郑显玉), Chang Dongwu(常东武), et al. Experimental study of the temperature impacts on the SO2 reduction ratio by ammonia gas scrubbing [J]. Acta Scientiae Circumstantiae(环境科学学报), 2002, 22(3): 412-416.
[8]	Chen Meiqian(陈梅倩), He Boshu(何伯述), Chen Guanghua(陈广华), et al. Chemical kinetics based analyses on SO2 removal reactions by ammonia scrubbing [J]. Acta Scientiae Circumstantiae (环境科学学报), 2005, 25(7): 886-890.
[9]	Bai H, Biswas P, Keener T C. SO2 removal by NH3 gas injection: effects of temperature and moisture content [J]. Ind. Eng. Chem. Res., 1994, 33(5): 1231-1236.
[10]	Hsunling Bai, Pratim Biswas, Tim C Keener. Particle formation by ammonia-sulfur dioxide reactions at trace water conditions [J]. Ind. Eng. Chem. Res., 1992, 31(1): 88-94.
[11]	Tock R W, Hoover K C, Faust G J. SO2 removal by transformation to solid crystals of ammonia complexes [J]. AIChE Symp. Ser., 1979, 75(188): 62-82.
[12]	Gao X, Ding H L, Du Z, et al. Gas-liquid absorption reaction between (NH4)2SO3 solution and SO2 for ammonia-based wet flue gas desulfurization [J]. Applied Energy, 2010, 87(8): 2647-2651.
[13]	Liu Guorong(刘国荣), Wang Zhengwei(王政威), Wei Yulei(魏玉垒), et al. Experimental study and modeling for ammonia desulphurization in spray tower [J]. CIESC Journal (化工学报), 2010, 61(9): 2463-2467 .
[14]	Bao Jingjing(鲍静静), Yin Huabin(印华斌), Yang Linjun(杨林军), et al. Formation characteristics of aerosols in wet ammonia-based desulphurization process [J]. Journal of Chemical Engineering of Chinese Universities (高校化学工程学报), 2010, 24(2): 325-330.
[15]	Bao Jingjing(鲍静静), Yang Linjun(杨林军), Yan Jinpei(颜金培), et al. Performance of removal of fine particles by WFGD system [J]. CIESC Journal (化工学报), 2009, 60(5): 1260-1267.
[16]	Bao Jingjing(鲍静静), Yin Huabin(印华斌), Yang Linjun(杨林军), et al. Removal of fine aerosol particles formed in wet ammon in flue gas desulfurization process by heterogeneous condensation [J]. Journal of Power Engineering(动力工程), 2009, 29(2): 178-183.
[17]	Yan Jinpei(颜金培), Yang Linjun(杨林军), Bao Jingjing(鲍静静), et al. Impact property on fine particles from coal combustion in ammonia flue gas desulfurization process [J]. Proceeding of the CSEE(中国电机工程学报), 2008, 29(5): 21-26.
[18]	Hao Jiming(郝吉明), Ma Guangda(马广大). Air Pollution Control Engineering(大气污染物控制工程) [M]. Beijing: Higher Education Press, 2011: 366.
[19]	St Clair H W. Vapor pressure and thermodynamic properties of ammonium sulphites [J]. US Bur. Mines Rept. Invest, 1937, (3339): 19.
[20]	Guo Y, Liu Z, Huang Z, et al. Reaction behavior of sulfur dioxide with ammonia [J]. Industrial & Engineering Chemistry Research, 2005, 44(26): 9989-9995.

氨法烟气脱硫过程中气溶胶颗粒生成特性

Properties of aerosol formation during wet ammonia-based desulfurization process

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献 20

相关文章 15

编辑推荐

Metrics

本文评价

[1]	王绍壮, 于敦喜, 李佳忆, 韩京昆, 喻鑫, 刘芳琪. 烟气烘焙对玉米秆可磨性的影响规律研究[J]. 化工学报, 2023, 74(2): 861-870.
[2]	马语峻, 刘向军. 多孔陶瓷膜烟气水分回收理论与模型研究[J]. 化工学报, 2022, 73(9): 4103-4112.
[3]	尹子骏, 苏胜, 卿梦霞, 赵志刚, 王中辉, 王乐乐, 江龙, 汪一, 胡松, 向军. 一种典型钒钛系SCR催化剂SO₃生成特性研究[J]. 化工学报, 2021, 72(5): 2596-2603.
[4]	游洋, 刘应书, 杨雄, 吴晓永, 赵春雨, 王正, 侯环宇, 李子宜. 面向烟气NO_x净化与回收的新型吸附工艺[J]. 化工学报, 2021, 72(4): 2132-2138.
[5]	张昊, 董勇, 赖艳华, 崔琳, 杨潇. 用于燃煤烟气除湿消白的湿电平板降膜模拟及试验研究[J]. 化工学报, 2021, 72(4): 2249-2257.
[6]	卿梦霞, 张鑫, 刘亮, 张巍, 王乐乐, 苏胜, 孔凡海, 向军. 燃煤烟气脱硝副产物硫酸氢铵/硫酸铵沉积与分解特性研究[J]. 化工学报, 2021, 72(2): 1132-1141.
[7]	朱肖, 冯厦厦, 仲兆祥, 邢卫红. 用于空气净化的双疏膜制备及应用进展[J]. 化工学报, 2021, 72(1): 71-85.
[8]	马双忱, 周权, 曹建宗, 刘琦, 陈文通, 樊帅军, 要亚坤, 林宸雨, 马彩妮. 湿法脱硫系统动态过程建模与仿真[J]. 化工学报, 2020, 71(8): 3741-3751.
[9]	孙宗康, 张笑丹, 杨林军, 陈帅, 吴新. 化学与湍流团聚耦合促进燃煤细颗粒物团聚与脱除[J]. 化工学报, 2020, 71(3): 1317-1325.
[10]	刘丹, 成毅, 胡明月, 盛倩云, 周昊. 湿烟气工况下齿形螺旋翅片管束的性能研究[J]. 化工学报, 2020, 71(2): 575-583.
[11]	常程,姬忠礼,刘佳霖. 亲油型聚结滤芯饱和度预测模型研究[J]. 化工学报, 2020, 71(12): 5610-5619.
[12]	王昱焜, 张现仁, 曹达鹏. 利用κ-Köhler理论研究大气气溶胶的吸湿特性[J]. 化工学报, 2019, 70(7): 2691-2698.
[13]	曲江源, 齐娜娜, 关彦军, 滕阳, 徐文青, 朱廷钰, 张锴. 湿法烟气脱硫塔内传递与化学反应过程CFD模拟[J]. 化工学报, 2019, 70(6): 2117-2128.
[14]	曹语, 王乐, 季超, 黄延召, 薛志磊, 陆剑鸣, 漆虹. 陶瓷膜冷凝器用于烟气脱白烟过程的中试研究[J]. 化工学报, 2019, 70(6): 2192-2201.
[15]	贾勇, 蒋进, 赵忍, 荣卫龙, 殷李国, 顾明言, 龙红明. 氨法烟气脱硫SO₂吸收传质系数研究[J]. 化工学报, 2019, 70(4): 1367-1374.