CIESC Journal ›› 2016, Vol. 67 ›› Issue (6): 2638-2644.DOI: 10.11949/j.issn.0438-1157.20151148

Previous Articles    

Preparation of biomass-based activated carbon with high-mesoporosity by direct zinc chloride activation

XING Xianjun1, SUN Zongkang2, FAN Fangyu2, MA Peiyong1,2, ZHANG Xianwen1, YU Jin2, WU Zhaobin2   

  1. 1. Advanced Energy Technology and Equipment Research Institute, Hefei University of Technology, Hefei 230009, Anhui, China;
    2. Department of Mechanical and Automobile Engineering, Hefei University of Technology, Hefei 230009, Anhui, China
  • Received:2015-07-17 Revised:2016-03-11 Online:2016-06-05 Published:2016-06-05
  • Supported by:

    supported by the National Key Technology Research and Development Program of China (2012BAD30B01).

干法制备高中孔率生物质成型活性炭

邢献军1, 孙宗康2, 范方宇2, 马培勇1,2, 张贤文1, 虞浸2, 吴照斌2   

  1. 1. 合肥工业大学先进能源技术与装备研究院, 安徽 合肥 230009;
    2. 合肥工业大学机械与汽车工程学院, 安徽 合肥 230009
  • 通讯作者: 邢献军
  • 基金资助:

    国家科技支撑计划项目(2012BAD30B01)。

Abstract:

The high-mesoporosity activated carbon was prepared from sawdust by zinc chloride activation. Before activation, the zinc chloride and sawdust were mixed directly without binder or water. In order to investigate the feasibility of this process, the effects of factors such as impregnation ratio, activation temperature, activation time and the density on methylene blue adsorption properties of the activated carbon were studied. The results showed that the optimum conditions were impregnation ratio 1.0:1, activation temperature 950℃, activation time 60 min and the density 1.4 g·cm-3. The activated carbon prepared under the optimized conditions had a methylene blue adsorption value of 387 mg·g-1, a BET surface area of 2104 m2·g-1 and the average pore diameter of 3.11 nm. The total pore volume of the activated carbon was 1.63 cm3·g-1 with a mesopore volume of 1.17 cm3·g-1, yielding a high mesopore percentage of 71.8%. The results showed that the activated carbon had an excellent adsorption capacity due to its large surface area and well-developed mesopore structure, indicating the feasibility of the dry process.

Key words: biomass, activated carbon, mesoporous, formed, adsorption, dry process

摘要:

以锯末为原料,氯化锌为活化剂,不添加黏结剂,采用干法混合后直接成型活化制备高中孔率生物质成型活性炭。为考察这种工艺的可行性,通过单因素实验,以亚甲基蓝吸附值为评价指标,考察了盐料比、活化温度、活化时间与成型密度对生物质成型活性炭吸附性能的影响,得出较优工艺条件为:盐料比1.0:1,活化温度950℃,活化时间为60min,成型密度为1.4g·cm-3。在此工艺条件下制备得到的生物质成型活性炭,其亚甲基蓝吸附值为387mg·g-1,BET比表面积为2104m2·g-1,平均孔径为3.11nm,总孔容为1.63cm3·g-1,中孔孔容为1.17cm3·g-1,中孔率高达71.8%,初步证明了干法制备高中孔率生物质成型活性炭工艺的可行性。

关键词: 生物质, 活性炭, 中孔, 成型, 吸附, 干法

CLC Number: