多液滴同步冲击液膜时中间薄膜射流形成机理与动力学特征

doi:10.11949/j.issn.0438-1157.20180179

化工学报 ›› 2018, Vol. 69 ›› Issue (8): 3356-3363.DOI: 10.11949/j.issn.0438-1157.20180179

多液滴同步冲击液膜时中间薄膜射流形成机理与动力学特征

梁刚涛, 张天宇, 陈红亮, 余海兵, 沈胜强

大连理工大学能源与动力学院, 辽宁大连 116024

收稿日期:2018-02-08 修回日期:2018-03-09 出版日期:2018-08-05 发布日期:2018-08-05
通讯作者: 梁刚涛
基金资助:
国家自然科学基金项目（51506023，51336001）；中央高校基本科研业务费专项资金项目（DUT17RC（4）22）。

Central sheet formation mechanism and dynamic characteristics in simultaneous impact of multiple droplets on liquid film

LIANG Gangtao, ZHANG Tianyu, CHEN Hongliang, YU Haibing, SHEN Shengqiang

School of Energy and Power Engineering, Dalian University of Technology, Dalian 116024, Liaoning, China

Received:2018-02-08 Revised:2018-03-09 Online:2018-08-05 Published:2018-08-05
Supported by:
supported by the National Natural Science Foundation of China (51506023, 51336001) and the Fundamental Research Funds for the Central Universities of Ministry of Education of China (DUT17RC(4)22).

摘要/Abstract

摘要：

采用耦合水平集-流体体积（coupled level set and volume of fluid）方法结合高斯随机分布扰动对多液滴同步冲击平面液膜飞溅过程进行了三维数值模拟，通过分析压力、速度等细微场量分布，揭示了中间薄膜射流的生成、破碎以及后期柱状射流的形成机理。此外，讨论了Weber数、液膜厚度、液滴间距对薄膜射流高度的作用规律。结果表明，在液相加入高斯分布扰动后可以充分反映液滴冲击飞溅特征；相邻液滴颈部区域射流接触后，接触区压力梯度骤然升高，与流体运动间断共同作用下形成向上运动的薄膜射流，随后在流体不稳定性与气相涡流作用下发生破碎；薄膜射流高度随Weber数和液膜厚度升高而增大，液滴间距减小时，射流高度增大。

关键词: 液滴冲击, 液膜, 射流, 飞溅

Abstract:

This study employed the method of coupled level set and volume of fluid (CLSVOF) to simulate simultaneous impact of multiple droplets on a liquid film three-dimensionally, and focused on the splashing process with the implement of Gaussian distribution to generate perturbation on liquid phase. The formation and break-up mechanisms of the central sheet and the formation mechanism of the column jet were revealed through analyzing pressure and velocity distributions after impingement. The effects of impact Weber number, film thickness and droplet interval were discussed. It is shown that the splashing characteristics can be well predicted with the use of Gaussian distribution on liquid phase. After the neck-jet or crown liquid sheet contacting with each other, a great pressure gradient is produced in the contact region, which leads to production of the upward-moving central liquid sheet with the conjunct motivation of fluid kinematic discontinuity and breaks up under the effects of fluid instability and gas vortex. The central sheet height increases with increasing Weber number and film thickness, or with decreasing droplet interval.

Key words: droplet impact, liquid film, sheet, splashing

中图分类号:

O359⁺.1

梁刚涛, 张天宇, 陈红亮, 余海兵, 沈胜强. 多液滴同步冲击液膜时中间薄膜射流形成机理与动力学特征[J]. 化工学报, 2018, 69(8): 3356-3363.

LIANG Gangtao, ZHANG Tianyu, CHEN Hongliang, YU Haibing, SHEN Shengqiang. Central sheet formation mechanism and dynamic characteristics in simultaneous impact of multiple droplets on liquid film[J]. CIESC Journal, 2018, 69(8): 3356-3363.

参考文献 30

[1]	梁刚涛, 牟兴森, 郭亚丽, 等. 液滴冲击加热壁面沸腾现象特征分析[J]. 化工学报, 2016, 67(6):2211-2217. LIANG G T, MU X S, GUO Y L, et al. Characteristic analysis of boiling phenomena from drop impinging on heated surfaces[J]. CIESC Journal, 2016, 67(6):2211-2217.
[2]	LIANG G, MUDAWAR I. Review of spray cooling (Ⅰ):Single-phase and nucleate boiling regimes, and critical heat flux[J]. Int. J. Heat Mass Transfer, 2017, 115:1174-1205.
[3]	LIANG G, MUDAWAR I. Review of spray cooling(Ⅱ):High temperature boiling regimes and quenching applications[J]. Int. J. Heat Mass Transfer, 2017, 115:1206-1222.
[4]	JOSSERAND C, THORODDSEN S T. Drop impact on solid surface[J]. Annu. Rev. Fluid Mech., 2016, 48:365-391.
[5]	FUJIMOTO H, ITO S I, TAKEZAKI I. Experimental study of successive collision of two water droplets with a solid[J]. Exp. Fluids, 2002, 33(3):500-502.
[6]	FEDORCHENKO A I, WANG A B. On some common features of drop impact on liquid surfaces[J]. Phys. Fluids, 2004, 16(5):1349-1365.
[7]	BERNARDIN J D, MUDAWAR I. Film boiling heat transfer of droplet streams and sprays[J]. Int. J. Heat Mass Transfer, 1997, 40(11):2579-2593.
[8]	BERNARDIN J D, MUDAWAR I, WALSH C B, et al. Contact angle temperature dependence for water droplets on practical aluminum surfaces[J]. Int. J. Heat Mass Transfer, 1997, 40(5):1017-1033.
[9]	LIANG G, MUDAWAR I. Review of mass and momentum interactions during drop impact on a liquid film[J]. Int. J. Heat Mass Transfer, 2016, 101:577-599.
[10]	LIANG G, MUDAWAR I. Review of drop impact on heated walls[J]. Int. J. Heat Mass Transfer, 2017, 106:103-126.
[11]	OKAWA T, SHIRAISHI T, MORI T. Production of secondary drops during the single water drop impact onto a plane water surface[J]. Exp. Fluids, 2006, 41(6):965-974.
[12]	VANDER WAL R, BERGER G, MOZES S. Droplets splashing upon films of the same fluid of various depths[J]. Exp. Fluids, 2006, 40(1):33-52.
[13]	COSSALI G E, COGHE A, MARENGO M. The impact of a single drop on a wetted solid surface[J]. Exp. Fluids, 1997, 22(6):463-472.
[14]	YARIN A L, WEISS D A. Impact of drops on solid surfaces:self-similar capillary waves, and splashing as a new type of kinematic discontinuity[J]. J. Fluid Mech., 1995, 283:141-173.
[15]	梁刚涛, 郭亚丽, 沈胜强. 液滴撞击液膜的射流与水花形成机理分析[J]. 物理学报, 2013, 62(2):024705. LIANG G T, GUO Y L, SHEN S Q. Analysis of liquid sheet and jet flow mechanism after droplet impinging onto liquid film[J]. Acta Phys. Sin., 2013, 62(2):024705.
[16]	DEEGAN R D, BRUNET P, EGGERS J. Complexities of splashing[J]. Nonlinearity, 2008, 21(1):1-14.
[17]	COSSALI G E, MARENGO M, SANTINI M. Impact of single and multiple drop array on a liquid film[C]//Proc. 19th ILASS-Europe. Nottingham, UK, 2004.
[18]	XU X, OUYANG J, JIANG T, et al. Numerical analysis of the impact of two droplets with a liquid film using an incompressible SPH method[J]. J. Eng. Math., 2014, 85(1):35-53.
[19]	GUO J, DAI S. Numerical simulation on the mechanism of the normal impact of two droplets onto a thin film[J]. J. Shanghai Univ. (Engl. Ed.), 2007, 11(3):210-212.
[20]	WU J, LIU C, ZHAO N. Dynamics of falling droplets impact on a liquid film:hybrid lattice Boltzmann simulation[J]. Colloids Surf. A, 2015, 472:92-100.
[21]	RAMAN K A, JAIMAN R K, LEE T S, et al. On the dynamics of crown structure in simultaneous two droplets impact onto stationary and moving liquid film[J]. Comput. Fluids, 2015, 107:285-300.
[22]	RAMAN K A, JAIMAN R K, LEE T S, et al. Dynamics of simultaneously impinging drops on a dry surface:role of impact velocity and air inertia[J]. J. Colloid Interface Sci., 2017, 486:265-276.
[23]	刘红, 贾小娟, 解茂昭, 等. 双液滴同时垂直撞击液膜数值研究[J]. 大连理工大学学报, 2013, 53(5):659-665. LIU H, JIA X J, XIE M Z, et al. Numerical investigation on two droplets normally onto liquid film[J]. J. Dalian Univ. Technol., 2013, 53(5):659-665.
[24]	王磊, 淮秀兰, 陶毓伽, 等. 喷雾冷却中微液滴碰撞薄液膜的流动与换热[J]. 工程热物理学报, 2010, 31(6):987-990. WANG L, HUAI X L, TAO Y J, et al. Flow and heat trnasfer of micro-droplet impact on thin liquid film during spray cooling[J]. J. Eng. Thermophys., 2010, 31(6):987-990.
[25]	SUSSMAN M, PUCKETT E G. A coupled level set and volume-of-fluid method for computing 3D and axisymmetric incompressible two-phase flows[J]. J. Comput. Phys., 2000, 162(2):301-337.
[26]	YOUNGS D L. Time-dependent Multi-material Flow with Large Fluid Distortion[M]. New York:Academic Press, 1982.
[27]	BRACKBILL J U, KOTHE D B, ZEMACH C. A continuum method for modeling surface tension[J]. J. Comput. Phys., 1992, 100(2):335-354.
[28]	MEHDIZADEH N Z, CHANDRA S, MOSTAGHIMI J. Formation of fingers around the edges of a drop hitting a metal plate with high velocity[J]. J. Fluid Mech., 2004, 510:353-373.
[29]	COSSALI G E, MARENGO M, COGHE A, et al. The role of time in single drop splash on thin film[J]. Exp. Fluids, 2004, 36(6):888-900.
[30]	LIANG G, GUO Y, SHEN S, et al. Crown behavior and bubble entrainment during a drop impact on a liquid film[J]. Theor. Comput. Fluid Dyn., 2014, 28(2):159-170.

多液滴同步冲击液膜时中间薄膜射流形成机理与动力学特征

Central sheet formation mechanism and dynamic characteristics in simultaneous impact of multiple droplets on liquid film

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献 30

相关文章 15

编辑推荐

Metrics

本文评价

[1]	张贲, 王松柏, 魏子亚, 郝婷婷, 马学虎, 温荣福. 超亲水多孔金属结构驱动的毛细液膜冷凝及传热强化[J]. 化工学报, 2023, 74(7): 2824-2835.
[2]	郑志航, 马郡男, 闫子涵, 卢春喜. 提升管射流影响区内压力脉动特性研究[J]. 化工学报, 2023, 74(6): 2335-2350.
[3]	赵健, 周兴超, 夏丹, 董航. 机械搅拌对原油储罐射流加热过程传热特性的影响规律研究[J]. 化工学报, 2023, 74(5): 1982-1999.
[4]	袁子涵, 王淑彦, 邵宝力, 谢磊, 陈曦, 马一玫. 基于幂律液固曳力模型流化床内湿颗粒流动特性的研究[J]. 化工学报, 2023, 74(5): 2000-2012.
[5]	廖珊珊, 张少刚, 陶骏骏, 刘家豪, 汪金辉. 竖直射流火撞击障碍管道数值模拟分析[J]. 化工学报, 2022, 73(9): 4226-4234.
[6]	罗佳, 吴双应, 肖兰, 周世耀, 陈志莉. 撞击速度对连续液滴撞击热圆柱壁面局部传热特性影响的实验[J]. 化工学报, 2022, 73(7): 2944-2951.
[7]	刘梦溪, 范怡平, 闫子涵, 姚秀颖, 卢春喜. 提升管进料区内气体射流流动行为的调控及工业应用[J]. 化工学报, 2022, 73(6): 2496-2513.
[8]	李岩, 田阿慧, 周毅. 反应性双射流中标量输运和化学反应特性[J]. 化工学报, 2022, 73(5): 1947-1963.
[9]	刘冉, 李杰, 王玉兵, 詹洪波, 张大林. 微小菱形离散肋通道中R134a的冷凝换热实验研究[J]. 化工学报, 2022, 73(11): 4938-4947.
[10]	张建伟, 李保帅, 董鑫, 冯颖. 撞击流反应器内幂律流体流动特性的数值模拟[J]. 化工学报, 2022, 73(11): 4917-4927.
[11]	刘献飞, 王恒, 王方, 李志强, 朱彩霞, 张浩飞. 单螺杆膨胀机螺旋槽道内液膜分布均匀特性[J]. 化工学报, 2021, 72(S1): 336-341.
[12]	刘曙光, 钟文琪, 陈曦. 基于XCT的气固流化床布风板射流特征研究[J]. 化工学报, 2021, 72(9): 4553-4563.
[13]	朱业铭, 刘金平, 许雄文, 朱丹丹. 竖直多孔平板上液膜流动特性的研究[J]. 化工学报, 2021, 72(8): 4081-4092.
[14]	吴兆伟, 施浙杭, 赵辉, 周骛, 蔡小舒, 刘海峰. 表面张力变化对含气泡液体射流破裂的影响[J]. 化工学报, 2021, 72(3): 1283-1294.
[15]	高峰, 陈永昌, 赵金龙, 马重芳. 磁场对熔盐射流冲击传热的影响[J]. 化工学报, 2020, 71(S2): 92-97.