烧结矿余热回收竖罐内气固传热特性

doi:10.11949/j.issn.0438-1157.20150548

化工学报 ›› 2015, Vol. 66 ›› Issue (11): 4418-4423.DOI: 10.11949/j.issn.0438-1157.20150548

烧结矿余热回收竖罐内气固传热特性

冯军胜, 董辉, 刘靖宇, 梁凯

东北大学材料与冶金学院, 国家环境保护生态工业重点实验室, 辽宁沈阳 110819

收稿日期:2015-05-04 修回日期:2015-06-04 出版日期:2015-11-05 发布日期:2015-11-05
通讯作者: 董辉
基金资助:
国家自然科学基金项目(51274065)。

Gas-solid heat transfer characteristics in vertical tank for sinter waste heat recovery

FENG Junsheng, DONG Hui, LIU Jingyu, LIANG Kai

SEPA Key Laboratory on Eco-industry, School of Materials and Metallurgy, Northeastern University, Shenyang 110819, Liaoning, China

Received:2015-05-04 Revised:2015-06-04 Online:2015-11-05 Published:2015-11-05
Supported by:
supported by the National Natural Science Foundation of China (51274065).

摘要/Abstract

摘要：

以自制气固传热实验装置为操作平台,实验研究了烧结矿颗粒填充床内的气固传热特性。结果表明:气体表观流速和烧结矿颗粒直径是影响颗粒床层内气固传热过程的主要因素。气体表观流速越大,颗粒直径越小,床层内气固传热系数就越大。当烧结矿颗粒直径和气体表观流速一定时,床层内烧结矿颗粒温度的升高导致床层气固传热系数的增加和传热Nusselt数的减小。由于计算误差较大,现有的经验关联式不适用于求解烧结矿颗粒床层内的气固传热过程。基于量纲分析法,并结合实验测量数据拟合得出了能够描述烧结矿颗粒床层内气固传热特性的实验关联式,平均计算误差为4.22%,显示了良好的预测性能。

关键词: 烧结, 填充床, 竖罐, 多孔介质, 传热系数

Abstract:

With a homemade gas-solid heat transfer experimental setup, an experimental study was conducted on gas-solid heat transfer characteristics in a packed bed with sinter particles. The results show that the main factors affecting the gas-solid heat transfer process in sinter bed layer are gas superficial velocity and sinter particle diameter. With the increase of gas superficial velocity and the decrease of sinter particle diameter, the gas-solid heat transfer coefficient increases in the sinter bed. For given gas superficial velocity and sinter particle diameter, higher sinter particle temperature in the bed gives higher gas-solid heat transfer coefficient and lower Nusselt number of heat transfer. Due to the large calculation error, the existing prediction correlations are not suitable for the gas-solid heat transfer process in sinter bed. Based on the method of dimensional analysis, an experimental correlation for describing the gas-solid heat transfer characteristics in sinter bed is obtained by fitting the experimental data, and its mean deviation from experimental data is 4.22%, giving good prediction.

Key words: sintering, packed bed, vertical tank, porous media, heat transfer coefficient

中图分类号:

TK11⁺5

冯军胜, 董辉, 刘靖宇, 梁凯. 烧结矿余热回收竖罐内气固传热特性[J]. 化工学报, 2015, 66(11): 4418-4423.

FENG Junsheng, DONG Hui, LIU Jingyu, LIANG Kai. Gas-solid heat transfer characteristics in vertical tank for sinter waste heat recovery[J]. CIESC Journal, 2015, 66(11): 4418-4423.

参考文献 21

[1]	Cai Jiuju (蔡九菊), Wang Jianjun (王建军), Chen Chunxia (陈春霞), Lu Zhongwu (陆钟武). Waste heat recovery and utilization in iron and steel industry [J]. Iron and Steel (钢铁), 2007, 42 (6): 1-7.
[2]	Dong Hui (董辉), Zhao Yong (赵勇), Cai Jiuju (蔡九菊), Zhou Jiewang (周节旺), Ma Guangyu (马光宇). On the air leakage problem in sintering cooling system [J]. Iron and Steel (钢铁), 2012, 47 (1):95-99.
[3]	Marcelo R E, Luiz F M. Thermodynamic analysis of a coke dry quenching unit [J]. Energ. Convers. Manage., 2000, 41 (2): 109-127.
[4]	Dong Hui, Jia Fengrui, Zhao Yong, Wang Meng, Cai Jiuju. Experimental investigation on the drying process of the sinter mixture [J]. Powder Technol., 2012, 218: 1-4.
[5]	Cai Jiuju (蔡九菊), Dong Hui (董辉). The method and device of sintering waste heat recovery and utilization with vertical tank [P]: CN, 200910187381.8. 2009-09-15.
[6]	Dong Hui (董辉), Li Lei (李磊), Liu Wenjun (刘文军), Wang Bo (王博), Suo Yanshuai (索延帅), Cai Jiuju (蔡九菊). Process of waste heat recovery and utilization for sinter in vertical tank [J]. China Metallurgy (中国冶金), 2012, 22 (1): 6-11.
[7]	Wakao N, Kaguei S. Heat and Mass Transfer in Packed Beds [M]. New York: McGraw-Hill, 1982.
[8]	Whitaker S. Forced convection heat transfer correlations for flow in pipes, past flat plates, single cylinders, single spheres, and for flow in packed beds and tube bundles [J]. AIChE J., 1972, 18 (2): 361-371.
[9]	Kays W M, London A L. Compact Heat Exchangers [M]. New York: McGraw-Hill, 1984.
[10]	Nie Xiaodong, Evitts R, Besant R, Bolster J. A new technique to determine convection coefficients with flow through particle beds [J]. J. Heat Transfer, 2011, 133 (4): 41-60.
[11]	Kuwahara F, Shirota M, Nakayama A. A numerical study of interfacial convective heat transfer coefficient in two-energy equation model for convection in porous media [J]. Int. J. Heat Mass Tran., 2001, 44 (6): 1153-1159.
[12]	Abdulmohsin R S, Al-Dahha M H. Characteristics of convective heat transport in a packed pebble-bed reactor [J]. Nucl. Eng. Des., 2015, 284: 143-152.
[13]	Yang Jian, Wang Jing, Bu Shanshan, Zeng Min, Wang Qiuwang, Nakayama A. Experimental analysis of forced convective heat transfer in novel structured packed beds of particles [J]. Chem. Eng. Sci., 2012, 71 (26): 126-137.
[14]	Thakur N S, Saini J S, Solanki S C. Heat transfer and friction factor correlations for packed bed solar air heater for a low porosity system [J]. Sol. Energy, 2003, 74 (4): 319-329.
[15]	Peši? R, Radoi?i? T K, Boškovi?-Vragolovi? N, Arsenijevi? Z, Grbav?i? ?. Heat transfer between a packed bed and a larger immersed spherical particle [J]. Int. J. Heat Mass Tran., 2014, 78: 130-136.
[16]	Cong T N, He Yurong, Chen Haisheng, Ding Yulong, Wen Dongsheng. Heat transfer of gas-solid two-phase mixtures flowing through a packed bed under constant wall heat flux conditions [J]. Chem. Eng. J., 2007, 130 (1): 1-10.
[17]	Geldart D. Estimation of basic particle properties for use in fluid-particle process calculations [J]. Powder Technol., 1990, 60 (1): 1-13.
[18]	Klerk A D. Voidage variation in packed beds at small column to particle diameter ratio [J]. AIChE J., 2003, 49 (8): 2022-2029.
[19]	Gupta A S, Thodos G. Mass and heat transfer in the flow of fluids through fixed and fluidized beds of spherical particles [J]. AIChE J., 1962, 8 (5): 608-610.
[20]	Ranz W E, Marshall W R. Evaporation from drops [J]. Chem. Eng. Prog., 1952, 48: 141-146.
[21]	Gupta S N, Chaube R B, Upadhyay S N. Fluid-particle heat transfer in fixed and fluidized beds [J]. Chem. Eng. Sci., 1974, 29 (3): 839-843.

烧结矿余热回收竖罐内气固传热特性

Gas-solid heat transfer characteristics in vertical tank for sinter waste heat recovery

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献 21

相关文章 15

编辑推荐

Metrics

本文评价

[1]	杨越, 张丹, 郑巨淦, 涂茂萍, 杨庆忠. NaCl水溶液喷射闪蒸-掺混蒸发的实验研究[J]. 化工学报, 2023, 74(8): 3279-3291.
[2]	曾如宾, 沈中杰, 梁钦锋, 许建良, 代正华, 刘海峰. 基于分子动力学模拟的Fe₂O₃纳米颗粒烧结机制研究[J]. 化工学报, 2023, 74(8): 3353-3365.
[3]	史昊鹏, 钟达文, 廉学新, 张君峰. 朝下多尺度沟槽翅片结构表面沸腾换热实验研究[J]. 化工学报, 2023, 74(7): 2880-2888.
[4]	贾晓宇, 杨剑, 王博, 林梅, 王秋旺. 金属丝网毛细特性的孔隙尺度数值分析[J]. 化工学报, 2023, 74(5): 1928-1938.
[5]	葛泽峰, 吴雨青, 曾名迅, 查振婷, 马宇娜, 侯增辉, 张会岩. 灰化学成分对生物质气化特性的影响规律[J]. 化工学报, 2023, 74(5): 2136-2146.
[6]	胡香凝, 尹渊博, 袁辰, 是赟, 刘翠伟, 胡其会, 杨文, 李玉星. 成品油在土壤中运移可视化的实验研究[J]. 化工学报, 2023, 74(4): 1827-1835.
[7]	张银宁, 王进卿, 冯致, 詹明秀, 徐旭, 张光学, 池作和. 升温条件下多孔介质内气泡的生长和聚并行为[J]. 化工学报, 2023, 74(4): 1509-1518.
[8]	杨辉著, 兰精灵, 杨月, 梁嘉林, 吕传文, 朱永刚. 高功率平板热管传热性能的实验研究[J]. 化工学报, 2023, 74(4): 1561-1569.
[9]	王晓萱, 胡晓红, 陆雨楠, 王士勇, 凡凤仙. 旋转膜过滤器内部流动特性数值模拟[J]. 化工学报, 2023, 74(4): 1489-1498.
[10]	钱志广, 樊越, 王世学, 岳利可, 王金山, 朱禹. 吹扫条件对PEMFC阻抗弛豫现象和低温启动的影响[J]. 化工学报, 2023, 74(3): 1286-1293.
[11]	李亚芾, 付亮亮, 白浩隆, 白丁荣, 许光文. 菱镁矿浮选尾矿直接合成同时制备镁橄榄石和镁砂研究[J]. 化工学报, 2022, 73(8): 3679-3687.
[12]	王沛, 魏荣阔. 光热驱动多孔氧化铈热化学循环解水制氢非热质平衡模型[J]. 化工学报, 2022, 73(7): 2885-2894.
[13]	郭志强, 燕可洲, 张吉元, 柳丹丹, 高阳艳, 郭彦霞. 煤矸石/粉煤灰对赤泥钠化还原焙烧反应的影响机制[J]. 化工学报, 2022, 73(5): 2194-2205.
[14]	张宇伦, 陈长坤, 雷鹏. 不同可燃液体层高度下浸润多孔介质砂床组合燃烧特性实验研究[J]. 化工学报, 2022, 73(4): 1826-1833.
[15]	王晔, 张婉雨, 汪彬, 耑锐, 任枫, 蔡爱峰, 杨光, 吴静怡. 多孔网幕泡破压力预测模型的建立及实验验证[J]. 化工学报, 2022, 73(3): 1102-1110.