典型螺旋槽端面干式气体密封动压开启性能

doi:10.3969/j.issn.0438-1157.2013.01.037

化工学报 ›› 2013, Vol. 64 ›› Issue (1): 326-333.DOI: 10.3969/j.issn.0438-1157.2013.01.037

典型螺旋槽端面干式气体密封动压开启性能

彭旭东, 刘坤, 白少先, 李纪云, 盛颂恩

浙江工业大学过程装备及其再制造教育部工程研究中心,浙江杭州 310032

收稿日期:2012-06-24 修回日期:2012-07-27 出版日期:2013-01-05 发布日期:2013-01-05
通讯作者: 彭旭东
作者简介:彭旭东(1964—),男,教授。
基金资助:
国家自然科学基金项目(50805130, 51175740);浙江省自然科学基金杰出青年团队项目(R1090833);教育部博士点基金项目(20103317110002)。

Dynamic opening characteristics of dry gas seals with typical types of spiral grooves

PENG Xudong, LIU Kun, BAI Shaoxian, LI Jiyun, SHENG Song

MOE Engineering Research Center of Process Equipment and Its Remanufacture, Zhejiang University of Technology, Hangzhou 310032, Zhejiang, China

Received:2012-06-24 Revised:2012-07-27 Online:2013-01-05 Published:2013-01-05
Supported by:
supported by the National Natural Science Foundation of China (50805130, 51175740),Zhejiang Science Fund for Outstanding Youths (R1090833) and Ph.D.Programs Foundation of Ministry of Education of China (20103317110002).

摘要/Abstract

摘要： 型槽端面干式气体密封的开启特性对密封的启动、停车和运行具有重要实际意义。基于气体混合润滑理论,考虑密封端面粗糙度效应和端面间气体滑移流效应,建立了干式气体密封的动压开启性能分析模型。开展了螺旋槽端面干式气体密封、带内环槽的螺旋槽端面干式气体密封和雁型槽端面干式气体密封等三种典型型槽端面干式气体密封的临界动压开启性能研究,数值分析了不同工况下三种型槽密封端面气膜压力分布,研究了环颈长比、环颈宽比、平衡比、弹簧比压和密封压力对临界开启转速、动压开启力比等开启性能参数的影响规律。结果表明:端面型槽的动压效应直接决定干式气体密封的临界开启转速,平衡比、弹簧比压对密封的动压开启性能影响较大,而环颈长比影响很小;在相同操作条件下,三种型槽端面密封相比较,雁型槽端面干式气体密封最易开启,带内环槽的螺旋槽端面干式气体密封次之,螺旋槽端面干式气体密封最难开启。

关键词: 型槽, 干气密封, 动压, 开启特性

Abstract: The opening behavior of two sealing faces of a dry gas seal (DGS) with various types of specified grooves is very important for startup, shut down, and operation of the DGS.Based on the theory of gas mixed lubrication, a dynamic opening model for a DGS was developed by considering the effects of gaseous slip flow and surface roughness.In the present paper, the critical dynamic sealing behavior, especially the opening characteristics of three types of DGSs were studied, including the spiral-groove DGS (S-DGS), the spiral groove and annular groove DGS (AS-DGS), and the goose groove DGS (GS-DGS).The gas film pressure distributions between two sealing faces of three types of DGSs under different operating conditions were numerically analyzed.A series of simulations were carried out to study the influences of annular neck length ratio, annular neck width ratio, balance ratio, spring pressure and sealed medium pressure on the critical opening rotational speed and hydrodynamic opening force ratio.Results showed that the critical opening rotational speed was directly determined by dynamic pressure effect of the specified face grooves.Dynamic opening characteristics were greatly affected by balance ratio and spring pressure, and slightly affected by annular neck length ratio.A comparison of the dynamic opening characteristics among the three types of DGSs was made under the same operating conditions.The results showed that the GS-DGS opened most quickly, the AS-DGS secondly, and the S-DGS most slowly during the startup process.

Key words: typical specified grooves, dry gas seal, dynamic pressure, opening behavior

中图分类号:

TH117.2

彭旭东, 刘坤, 白少先, 李纪云, 盛颂恩. 典型螺旋槽端面干式气体密封动压开启性能[J]. 化工学报, 2013, 64(1): 326-333.

PENG Xudong, LIU Kun, BAI Shaoxian, LI Jiyun, SHENG Song. Dynamic opening characteristics of dry gas seals with typical types of spiral grooves[J]. CIESC Journal, 2013, 64(1): 326-333.

参考文献 14

[1]	Gu Yongquan(顾永泉).Just-lift-off phenomena and lift-off characteristics of mechanical face seals[J].Petro-chemical Equipment(石油化工设备), 2003,32(4):26-29
[2]	Faria M T C.An efficient finite element procedure for analysis of high-speed spiral groove gas face seals[J].ASME Journal of Tribology, 2001,123(1):205-210
[3]	Pecht G G, Netzel J P.Design and application of non-contacting gas lubricated seals for slow speed services[J].Lubrication Engineering,1999,55(7):20-25
[4]	Reddi M M, Chu T Y.Finite element solution of the steady-state compressible lubrication problem[J].ASME Journal of Lubrication Technology, 1970,92(3):495-503
[5]	Peng Xudong(彭旭东), Liang Shike(梁世克), Bai Shaoxian(白少先), Meng Xiangkai(孟祥铠), Sheng Song’en(盛颂恩).Critical opening characteristics of a laser surface texture hydrostatic gas mechanical seal[J].Lubrication Engineering(润滑与密封), 2010,35(3):1-4
[6]	Li Yefeng(李叶枫), Sheng Song’en(盛颂恩), Bai Shaoxian(白少先), Peng Xudong(彭旭东).Experimental research of a hydrodynamic multi-pored face gas seal at zero pressure[J].Lubrication Engineering(润滑与密封), 2010,35(8):8-11
[7]	Li Shuangxi(李双喜), Song Wenbo(宋文博), Zhang Qiuxiang(张秋翔), Cai Jining(蔡纪宁), Gao Jinji(高金吉).Opening characteristics of dry gas seal[J].CIESC Journal(化工学报), 2011,62(3):766-772
[8]	Peng Xudong(彭旭东), Tan Lili(谭丽丽), Sheng Song’en(盛颂恩), Bai Shaoxian(白少先), Li Jiyun(李纪云).Hydrostatic performance of a spiral groove and annular groove dry gas seal[J].Tribology(摩擦学学报), 2008,28(6):507-511
[9]	Huang Li(黄莉), Peng Xudong(彭旭东), Bai Shaoxian(白少先), Li Jiyun(李纪云), Sheng Song’en(盛颂恩).Comparison study on performance of three types of dry gas seal with different grooves[J].Fluid Machinery(流体机械), 2010,38(8):14-17
[10]	Ruan B, Salant R F, Green I.A mixed lubrication model of liquid/gas mechanical face seals[J].Tribology Transactions, 1997,40(4):647-657
[11]	Ruan B.Numerical modeling of dynamic sealing behaviors of spiral groove gas face seals[J].Tribology Transactions, 2002,124:186-195
[12]	Makino T, Morohoshi S, Taniguchi S.Application of average flow model to thin film gas lubrication[J].ASME Journal of Tribology, 1993,115(1):185-190
[13]	Peng Xudong(彭旭东), Huang Li(黄莉), Bai Shaoxian(白少先), Li Jiyun(李纪云), Gu Tongsheng(古通生).Numerical analysis of sealing performance of dry gas seal with goose-grooves[J].CIESC Journal(化工学报), 2010,61(12):3193-3199
[14]	Gabriel R P.Fundamentals of spiral groove non-contacting face seals[J].Lubrication Engineering, 1994,50(3):215-224

[1]	毕恩哲, 李双喜, 沙廉翔, 刘登宇, 陈凯放. 高温动压涨圈密封结构参数多目标优化分析[J]. 化工学报, 2023, 74(6): 2565-2579.
[2]	丁俊华, 俞树荣, 王世鹏, 洪先志, 包鑫, 丁雪兴. 多重效应下超高速干气密封流场模拟及密封性能试验[J]. 化工学报, 2023, 74(5): 2088-2099.
[3]	徐洁, 俞树荣, 丁雪兴, 蒋海涛, 丁俊华. 基于波箔片变形的浮动式箔片气膜密封性能分析[J]. 化工学报, 2022, 73(5): 2083-2093.
[4]	严如奇, 丁雪兴, 徐洁, 洪先志, 包鑫. 基于湍流模型的S-CO₂干气密封流场与稳态性能分析[J]. 化工学报, 2021, 72(8): 4292-4303.
[5]	江鹏, 江锦波, 彭旭东, 孟祥铠, 马艺. 传热模型对近临界工况CO₂干气密封温压分布和稳态性能影响[J]. 化工学报, 2021, 72(8): 4239-4254.
[6]	孙雪剑, 宋鹏云, 毛文元, 邓强国, 许恒杰, 陈维. 考虑密封环材料属性和表面形貌干气密封启停阶段的动态接触特性分析[J]. 化工学报, 2021, 72(8): 4279-4291.
[7]	江锦波, 滕黎明, 孟祥铠, 李纪云, 彭旭东. 基于多变量摄动的超临界CO₂干气密封动态特性[J]. 化工学报, 2021, 72(4): 2190-2202.
[8]	商浩, 陈源, 李孝禄, 王冰清, 李运堂, 彭旭东. 膜厚扰动下的非线性效应对干气密封性能影响研究[J]. 化工学报, 2021, 72(4): 2213-2222.
[9]	于辰,江锦波,赵文静,李纪云,彭旭东,王玉明. 基于微段组合的干气密封端面型槽结构模型及其参数影响[J]. 化工学报, 2021, 72(10): 5294-5309.
[10]	严如奇, 洪先志, 包鑫, 徐洁, 丁雪兴. 超临界二氧化碳干气密封相态分布规律与密封性能研究[J]. 化工学报, 2020, 71(8): 3681-3690.
[11]	范瑜, 宋鹏云, 许恒杰. 水蒸气润滑干气密封启动过程研究[J]. 化工学报, 2020, 71(8): 3671-3680.
[12]	俞树荣, 丁俊华, 王世鹏, 刘红, 丁雪兴, 孙宝财. 柱面密封气膜动压效应模拟及试验[J]. 化工学报, 2020, 71(7): 3220-3228.
[13]	陈维, 宋鹏云, 许恒杰, 孙雪剑. 含杂质二氧化碳实际气体干气密封性能研究[J]. 化工学报, 2020, 71(5): 2215-2229.
[14]	李世聪, 钱才富, 李双喜, 陈炼. 油气两相动压密封动态特性的热流固耦合研究[J]. 化工学报, 2020, 71(5): 2190-2201.
[15]	车健, 江锦波, 李纪云, 彭旭东, 马艺, 王玉明. 节流孔出气模式对静压干气密封稳态性能影响[J]. 化工学报, 2020, 71(4): 1734-1743.

典型螺旋槽端面干式气体密封动压开启性能

Dynamic opening characteristics of dry gas seals with typical types of spiral grooves

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献 14

相关文章 15

编辑推荐

Metrics

本文评价