微型流化床内气体返混

doi:10.3969/j.issn.0438-1157.2013.03.012

化工学报 ›› 2013, Vol. 64 ›› Issue (3): 867-876.DOI: 10.3969/j.issn.0438-1157.2013.03.012

微型流化床内气体返混

耿爽¹, 余剑¹, 张聚伟¹, 郭宏梅^1,2, 岳君容¹, 许光文¹

1. 中国科学院过程工程研究所多相复杂系统国家重点实验室,北京100190;
2. 沈阳化工大学化学工程学院,辽宁沈阳110142

收稿日期:2012-05-19 修回日期:2012-10-08 出版日期:2013-03-05 发布日期:2013-03-05
通讯作者: 余剑,许光文
作者简介:耿爽(1986—),男,硕士研究生。
基金资助:
国家自然科学基金项目(21106156,21006114);国家重大仪器专项(2011YQ120039)。

Gas back-mixing in micro fluidized beds

GENG Shuang¹, YU Jian¹, ZHANG Juwei¹, GUO Hongmei^1,2, YUE Junrong¹, XU Guangwen¹

1. State Key Laboratory of Multi-phase Complex System, Institute of Process Engineering, Chinese Academy of Sciences, Beijing 100190, China;
2. School of Chemical Engineering, Shenyang Institute of Chemical Technology, Shenyang 110142, Liaoning, China

Received:2012-05-19 Revised:2012-10-08 Online:2013-03-05 Published:2013-03-05
Supported by:
supported by the National Natural Science Foundation of China(21106156,21006114)and the National Instrumentation Grant(2011YQ120039).

摘要/Abstract

摘要： 微型流化床基础和应用在近几年受到越来越多的关注。针对微型流化床对气固反应分析的应用要求,利用脉冲示踪法研究了内径10 mm和21 mm两种尺寸微型流化床中的气体返混特性,具体考察了管内径、颗粒静床高度、床料颗粒粒径和气体表观流速对气体返混程度的影响。结果表明:随着床内径、颗粒静床高度和表观气速的减小和床料颗粒粒径的增大,气体在床内的返混程度减小。使用粒径约270 μm粗颗粒时,两种床径的浅层微型流化床中的气体返混程度都较小,对应的Peclet数在27以上,证明了床内气体流动接近平推流,从而为利用微型流化床最小化气体返混对反应测试的影响,获得近本征反应动力学参数提供了流动特性的保障。

关键词: 微型流化床, 气体返混, 气体停留时间分布, 气体示踪法, 微反应器

Abstract: More attention is being paid to the hydrodynamics and applications of micro fluidized beds in recent years.Considering the application of micro fluidized bed to gas-solids reaction analysis,the gas back-mixing characteristics in two beds of 10 mm and 21 mm inner diameter was studied by using the gas impulse tracer approach.The influences of bed diameter,static particle bed height,bed particle size and superficial gas velocity on the extent of gas back-mixing were investigated.It was shown that the extent of gas back-mixing increased with increasing inner bed diameter,static particle bed height and superficial gas velocity,but decreased with increasing bed particle size.The tested two micro fluidized beds that had a shallow layer of coarse particles in size of about 270 mm had both low extent of gas back-mixing and the estimated Peclet numbers for them were above 27,showing that the gas flow in these beds was very close to plug flow.This,as a consequence,verified that using micro fluidized bed for gas-solids reaction analysis could minimize the effect of gas back-mixing on reaction testing so as to get the near-intrinsic reaction kinetics.

Key words: micro fluidized bed, gas back-mixing, gas residence time distribution, gas tracer approach, micro reactor

中图分类号:

TQ021.4

耿爽, 余剑, 张聚伟, 郭宏梅, 岳君容, 许光文. 微型流化床内气体返混[J]. 化工学报, 2013, 64(3): 867-876.

GENG Shuang, YU Jian, ZHANG Juwei, GUO Hongmei, YUE Junrong, XU Guangwen. Gas back-mixing in micro fluidized beds[J]. CIESC Journal, 2013, 64(3): 867-876.

参考文献 33

[1]	Wang Chunhua(王春华),Chen Wenzhong(陈文仲),Chen Haigeng(陈海耿),Zuo Chunyou(左春友).Calculation of mean residence time of solids in variable diameter carbon rotary kiln[J].CIESC Journal(化工学报),2009,60(3):574-579
[2]	Guo Qingjie,Xu Yiquan,Yue Xuehai.Fluidization characteristics in micro-fluidized beds of various inner diameters[J].Chemical Engineering&Technology,2009,32(12):1992-1999
[3]	Xu Jianliang(许建良),Dai Zhenghua(代正华),Li Qiaohong(李巧红),Li Weifeng(李伟锋),Liu Haifeng(刘海峰),Wang Fuchen(王辅臣),Yu Zunhong(于遵宏).Particle residence time distributions in entrained-flow gasifier[J].Journal of Chemical Industry and Engineering(China)(化工学报),2008,59(1):53-57
[4]	Jin Yong(金涌),Zhu Jingxu(祝京旭),Wang Zhanwen(汪展文),Yu Zhiqing(俞芷青).Fluidization Engineering Principles(流态化工程原理)[M].Beijing:Tsinghua University Press,2001:13,36,160
[5]	Du Bing,Fan Liang-Shih,Wei Fei,Warsito W.Gas and solids mixing in a turbulent fluidized bed[J].Particle Technology and Fluidization,2002,48(9):1896-1909
[6]	Guo Falei.Gas flow and mixing behavior in fine-powder fluidized bed[J].AIChE Journal,1987,33(11):1895-1898
[7]	Bi H T,Ellis N,Abba I A,Grace J R.A state-of-the-art review of gas-solid turbulent fluidization[J].Chemical Engineering Science,2000, 55(21):4789-4825
[8]	Wei F,Lin S,Yang G.Gas and solids mixing in a commercial FCC regenerator[J].Chemical Engineering & Technology,1993,16(2):109-113
[9]	Chen Mingqiang(陈明强),Yan Yongjie(颜涌捷),Ren Zhengwei(任铮伟),Mao Yuanfu(毛元夫).Modeling of characteristics of particle residence time in continuous spout-fluid bed with draft tube[J].Journal of Chemical Industry and Engineering(China)(化工学报),1998,49(5):586-591
[10]	Yu Jian(余剑),Zhu Jianhong(朱剑虹),Xu Guangwen(许光文).Development and application of micro kinetic analyzer for fluidized bed gas-solid reactions[J].CIESC Journal(化工学报),2009,60(10):2669-2674
[11]	Yu Jian,Yao Changbin,Zeng Xi,Geng Shuang,Dong Li,Wang Yin,Gao Shiqiu,Xu Guangwen.Biomass pyrolysis in a micro-fluidized bed reactor:characterization and kinetics[J].Chemical Engineering Journal,2011,168(2):839-847
[12]	Yu Jian,Zeng Xi,Zhang Juwei,Zhong Mei,Zhang Guangyi,Wang Yin,Xu Guangwen.Isothermal differential characteristics of gas-solid reaction in micro-fluidized bed reactor[J].Fuel,2011,168(2):839-847
[13]	Potic B,Kersten S R A,Ye M,van der Hoef M A,Kuipers J A M,van Swaaij W P M.Fluidization with hot compressed water in micro-reactors[J].Chemical Engineering Science,2005,60(22):5982-5990
[14]	Wang J W,Tan L H,van der Hoef M A,van Sint Annaland M,Kuipers J A M.From bubbling to turbulent fluidization:advanced onset of regime transition in micro-fluidized beds[J].Chemical Engineering Science,2011,66(9):2001-2007
[15]	Xu Guangwen,Liu Xinhua,Gao Shiqiu.Micro fluidized beds:wall effect and operability[J].Chemical Engineering Journal,2008,137(2):302-307
[16]	Grace J,Bi H T,Zhang Yongmin.Pitfalls in gas sampling from fluidized beds[J].Chemical Engineering Science,2009,64(10):2522-2524
[17]	Deshmukh S A R K,Laverman J A,Cents A H G,van Sint Annaland M,Kuipers J A M.Development of a membrane-assisted fluidized bed reactor(Ⅰ):Gas phase back-mixing and bubble-to-emulsion phase mass transfer using tracer injection and ultrasound experiments[J].Industrial and Engineering Chemistry Research,2005,44 (16):5955-5965
[18]	Narvaez P C,Sanchez F J,Godoy-Silva R D.Continuous methanolysis of palm oil using a liquid-liquid film reactor[J].J.Am.Oil Chem.Soc.,2009, 86(4):343-352
[19]	Sylvie V,Julien C,Pierre C,Sebastien T,Anthony D,Guillaume B,Bertrand S.Upgrading biomass pyrolysis gas by conversion of methane at high temperature:experiments and modelling[J].Fuel,2009,88(5):834-842
[20]	Li Shaofen(李绍芬).Reaction Engineering(反应工程)[M].2nd ed.Beijing:Chemical Industry Press,2000:127-149
[21]	Behrens M,Hoffman H,Lincoln A.Chemical Reaction Engineering(化学反应工程)[M].Zhang Jiyan(张继炎),Xu Jianguo(徐建国),Qi Mingzhai(齐鸣斋),trans.Beijing:Sinopec Press,1994:400
[22]	Li Tingwen,Zhang Yongmin,Grace J,Bi H T.Numerical investigation of gas mixing in gas-solid fluidized beds[J].AIChE Journal,2010,56(9):2280-2296
[23]	Li Tingwen,Zhang Yongmin,Grace J,Bi H T.Numerical investigation of gas sampling from fluidized beds//Kim S D,Kang Y,Lee J K,Seo Y C.Proceeding of Fluidization ⅫⅠ.Gyeong-ju,Korea:ECI Digital Archives,2010:137-144
[24]	Lee G S,Kim S D.Axial mixing of solids in turbulent fluidized beds[J].Chemical Engineering Journal,1990,44(1):1-9
[25]	Werther J.Influence of bed diameter on the hydrodynamics of gas fluidized beds[J].AIChE Journal Symp.Ser.,1974,70(141):53
[26]	Shan Y T,Stiegel G J,Sharma M M.Backmixing in gas-liquid reactors[J].AIChE Journal,1978, 24(3):369-400
[27]	Deckwer W D.Absorption and reaction of isobutene in sulfuric acid(Ⅲ):Considerations on the scale up of bubble columns[J].Chemical Engineering Science,1977,32(1):51-57
[28]	Anderson W J,Pratt H R C.Wake shedding and circulatory flow in bubble and droplet-type contactors[J].Chemical Engineering Science,1978,33(8):995-1002
[29]	Bi H T,Ellis N,Abba I A,Grace J R.A state-of-the-art review of gas-solid turbulent fluidization[J].Chemical Engineering Science,2000,55(21):4789-4825
[30]	Cho Hong II,Chung Chan-Hwa,Han Gui Young,Ahn Gui Ryong,Kong Jong Su.Axial gas dispersion in a fluidized bed of polyethylene particles[J].Korean J.Chem.Eng.,2000,17(3):292-298
[31]	Chen Minheng(陈敏恒),Cong Dezi(丛德滋),Fang Tunan(方图南),Qi Mingzhai(齐鸣斋).Principles of Chemical Engineering(化工原理)[M].Beijing:Chemical Industry Press,2006:10
[32]	Gilliland E R,Mason E A.Gas and solid mixing in fluidized beds[J].Industrial and Engineering Chemistry,1949,41(6):1191-1196
[33]	Gilliland E R,Mason E A.Gas mixing in beds of fluidized solids[J].Industrial and Engineering Chemistry,1952,44(1):218-224

微型流化床内气体返混

Gas back-mixing in micro fluidized beds

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献 33

相关文章 15

编辑推荐

Metrics

本文评价

[1]	付家崴, 陈帅帅, 方凯伦, 蒋新. 微反应器共沉淀反应制备铜锰催化剂[J]. 化工学报, 2023, 74(2): 776-783.
[2]	谢煜, 张民, 胡卫国, 王玉军, 骆广生. 利用膜分散微反应器高效溶解D-7-ACA的研究[J]. 化工学报, 2023, 74(2): 748-755.
[3]	章承浩, 罗京, 张吉松. 微反应器内基于氮氧自由基催化剂连续氧气/空气氧化反应的研究进展[J]. 化工学报, 2023, 74(2): 511-524.
[4]	杨星宇, 马优, 朱春英, 付涛涛, 马友光. 梳状并行微通道内液液分布规律研究[J]. 化工学报, 2023, 74(2): 698-706.
[5]	王凯玥, 马永丽, 李琛, 刘明言. 气液固微型流化床的气液传质系数[J]. 化工学报, 2022, 73(8): 3529-3540.
[6]	顾仁杰, 张加威, 靳雪阳, 文利雄. 微撞击流反应器制备镍钴复合氢氧化物超级电容器材料及其性能研究[J]. 化工学报, 2022, 73(8): 3749-3757.
[7]	侯跃辉, 刘璇, 廉应江, 韩梅, 尧超群, 陈光文. 超声微反应器内三硝基间苯三酚合成工艺研究[J]. 化工学报, 2022, 73(8): 3597-3607.
[8]	张经纬, 周弋惟, 陈卓, 徐建鸿. 微反应器内的有机合成前沿进展[J]. 化工学报, 2022, 73(8): 3472-3482.
[9]	许非石, 杨丽霞, 陈光文. 超声微反应器内气液传质过程的介尺度强化机制[J]. 化工学报, 2022, 73(6): 2552-2562.
[10]	王宜飞, 王清强, 姬德生, 李申芳, 金楠, 赵玉潮. 微通道壁面浸润性对气-液两相流的影响规律研究[J]. 化工学报, 2022, 73(4): 1501-1514.
[11]	徐一鸣, 袁华, 刘素丽, 李平, 严佩蓉, 赵曦, 卢俊华, 赵唯, 张学兰. 微通道反应器中工业混合直链烷基苯磺酸盐的连续合成工艺研究[J]. 化工学报, 2022, 73(3): 1184-1193.
[12]	向亮, 钟子豪, 苏远海. 微反应器内连续制备拓扑结构聚合物的研究进展[J]. 化工学报, 2022, 73(12): 5275-5288.
[13]	方凯伦, 陈帅帅, 付家崴, 蒋新. 微反应器研究陈化过程对铜锰催化剂的影响[J]. 化工学报, 2022, 73(10): 4438-4447.
[14]	武鹏, 王芳, 曾玺, 战洪仁, 岳君容, 王婷婷, 许光文. 微型流化床中焦油热裂解和水蒸气重整的反应特性及动力学对比[J]. 化工学报, 2022, 73(1): 362-375.
[15]	王婷婷, 曾玺, 韩振南, 王芳, 武鹏, 许光文. 微型流化床中生物质半焦水蒸气气化反应特性及动力学研究[J]. 化工学报, 2022, 73(1): 294-307.