二次反应最小条件下聚氯乙烯塑料脱氯过程的实验

doi:10.3969/j.issn.0438-1157.2014.11.022

化工学报 ›› 2014, Vol. 65 ›› Issue (11): 4368-4375.DOI: 10.3969/j.issn.0438-1157.2014.11.022

• 催化、动力学与反应器 • 上一篇下一篇

二次反应最小条件下聚氯乙烯塑料脱氯过程的实验

罗嘉¹, 桂本², 万文军¹, 张曦¹, 王文霞³, 乔瑜³

1. 广东电网公司电力科学研究院, 广东广州 510080;
2. 中南电力设计院, 湖北武汉 430074;
3. 华中科技大学煤燃烧国家重点实验室, 湖北武汉 430074

收稿日期:2014-01-23 修回日期:2014-08-06 出版日期:2014-11-05 发布日期:2014-11-05
通讯作者: 乔瑜
基金资助:
国家重点基础研究发展计划项目(2011CB201505).

Experiment of polyvinyl chloride plastic dechlorination process under condition of minimum secondary reaction

LUO Jia¹, GUI Ben², WAN Wenjun¹, ZHANG Xi¹, WANG Wenxia³, QIAO Yu³

1. Guangdong Power Gird Corporation Electric Power Research Institute, Guangzhou 510080, Guangdong, China;
2. Central Southern Electric Power Design Institute, Wuhan 430074, Hubei, China;
3. State Key Laboratory of Coal Combustion of Huazhong University of Science and Technology, Wuhan 430074, Hubei, China

Received:2014-01-23 Revised:2014-08-06 Online:2014-11-05 Published:2014-11-05
Supported by:
supported by the National Basic Research Program of China (2011CB201505).

摘要/Abstract

摘要： 采用金属网反应器对PVC热解过程中温度范围300～800℃、升温速率1～1000 K·s^-1、停留时间0～120 s的热解气体释放特性开展了实验研究.并基于EPA-26A标准对热解气中HCl和Cl₂进行了检测.结果显示,HCl和Cl₂的产率均随着温度的升高、停留时间的增长而有所提高.降低升温速率能够提升气态产物总体产率但没有改变含氯气体的总体分布.热解实验中气态产物均以HCl为主,并伴随有少量的Cl₂生成;该结果也证实了在PVC热解脱氯过程中大量含氯自由基的存在,进一步证实了PVC热解过程遵循的是自由基链反应机理.此外,通过对PVC热解焦样的分析进一步发现PVC热解第一阶段链反应终止时的分子更接近于直链多烯烃结构而非聚合环状结构,环化反应在该阶段并未发生.

关键词: 聚氯乙烯, 脱氯, 二次反应, 金属网反应器, 化学反应, 反应器

Abstract: Pyrolysis experiments of polyvinylchloride (PVC) were performed using a wire-mesh reactor. Non-condensing gases were collected at a heating rate 1—1000 K·s^-1 with temperatures from 300℃ to 800℃ and a holding time from 0 to 120 s. EPA-method 26A was employed to determinate the concentrations of both Cl₂ and HCl. The results showed that the release of HCl and Cl₂ increased continually with increase of temperature and reaction time. Lower heating rate could make the total gas yield increase but do not change the chlorine distribution. Cl₂ seemed as an accompanied product during HCl release, which indicated that a bunch of free Cl radicals were involved in PVC thermal degradation. The results confirmed that the pyrolysis process of PVC plastic followed the free radical chain mechanism. Lastly, it was further indicated, by the analysis of PVC pyrolysis tar, that the products obtained at the first stage of PVC pyrolysis were straight-chain polyenes rather than ring structure compounds, i.e. occurring of cyclization reactions seemed impossible at the phase.

Key words: polyvinylchloride, chlorine release, secondary reaction, wire-mesh reactor, chemical reaction, reactor

中图分类号:

TQ325.3

罗嘉, 桂本, 万文军, 张曦, 王文霞, 乔瑜. 二次反应最小条件下聚氯乙烯塑料脱氯过程的实验[J]. 化工学报, 2014, 65(11): 4368-4375.

LUO Jia, GUI Ben, WAN Wenjun, ZHANG Xi, WANG Wenxia, QIAO Yu. Experiment of polyvinyl chloride plastic dechlorination process under condition of minimum secondary reaction[J]. CIESC Journal, 2014, 65(11): 4368-4375.

参考文献 19

[1]	Yang Tao(杨涛). Production, application and prospect of PVC resin in China [J]. China Plastic(中国塑料),2008, 22 (2): 1-8
[2]	Zhao Jizhi(赵季芝). The PVC industry present situation and the analysis of China's PVC industry [J]. Polyvinyl Chloride (聚氯乙烯), 2003 (6): 4-6
[3]	Liao Zhengpin(廖正品). Development status and trend of PVC processing industry in China [J]. Polyvinyl Chloride (聚氯乙烯), 2001 (3): 39-43
[4]	McNeill I C, Memetea L. Pyrolysis products of poly (vinyl chloride), dioctyl phthalate and their mixture [J]. Polymer Degradation and Stability,1994, 43 (1): 9-25
[5]	Zhu H, Jiang X, Yan J, Chi Y, Cen K. TG-FTIR analysis of PVC thermal degradation and HCl removal [J]. Journal of Analytical and Applied Pyrolysis, 2008, 82 (1): 1-9
[6]	Karayildirim T, Yanik J, Yuksel M, Saglam M, Vasile C, Bockhorn H. The effect of some fillers on PVC degradation [J]. Journal of Analytical and Applied Pyrolysis, 2006, 75 (2): 112-119
[7]	Miranda R, Pakdel H, Roy C, Darmstadt H, Vasile C. Vacuum pyrolysis of PVC (Ⅱ): Product analysis [J]. Polymer Degradation and Stability, 1999, 66 (1): 107-125
[8]	Miranda R, Yang J, Roy C, Vasile C. Vacuum pyrolysis of PVC (Ⅰ): Kinetic study [J]. Polymer Degradation and Stability, 1999, 64 (1): 127-144
[9]	Knümann R, Bockhorn H. Investigation of the kinetics of pyrolysis of PVC by TG-MS-analysis [J]. Combustion Science and Technology, 1994, 101 (6): 285-299
[10]	Kaminsky W, Kim J S. Pyrolysis of mixed plastics into aromatics [J]. Journal of Analytical and Applied Pyrolysis, 1999, 51 (1): 127-134
[11]	Ma S, Lu J, Gao J. Study of the low temperature pyrolysis of PVC [J]. Energy & Fuels, 2002, 16 (2): 338-342
[12]	Miranda R, Pakdel H, Roy C, Vasile C. Vacuum pyrolysis of commingled plastics containing PVC(II): Product analysis [J]. Polymer Degradation and Stability, 2001, 73 (1): 47-67
[13]	Zeng C, Wu H, et al. Effects of thermal pretreatment in helium on the pyrolysis behaviour of Loy Yang brown coal [J]. Fuel, 2005, 84: 1586-1592
[14]	Zeng C, Favas G, et al. Effects of pretreatment in steam on the pyrolysis behavior of Loy Yang brown coal [J]. Energy & Fuels, 2006, 20: 281-286
[15]	Göpel W, Anderson J, Frankel D, Jaehnig M, Phillips K, Schäfer J, Rocker G. Surface defects of TiO2 (110): a combined XPS, XAES and ELS study [J]. Surface Science, 1984, 139 (2): 333-346
[16]	Lascovich J, Giorgi R, Scaglione S. Evaluation of the sp2/sp3 ratio in amorphous carbon structure by XPS and XAES [J]. Applied Surface Science, 1991, 47 (1): 17-21
[17]	Asami K, Hashimoto K, Shimodaira S. XPS determination of compositions of alloy surfaces and surface oxides on mechanically polished iron-chromium alloys [J]. Corrosion Science, 1977, 17 (9): 713-723
[18]	Fogg P G, Gerrard W. Solubility of Gases in Liquids: A Critical Evaluation of Gas/Liquid Systems in Theory and Practice[M]. West Sussex: John Wiley & Sons Chichester, 1991
[19]	Gui B, Qiao Y, Wan D, Liu S, Han Z, Yao H, Xu M. Nascent tar formation during polyvinylchloride (PVC) pyrolysis [J]. Proceedings of the Combustion Institute, 2013 (34): 2321-2329

二次反应最小条件下聚氯乙烯塑料脱氯过程的实验

Experiment of polyvinyl chloride plastic dechlorination process under condition of minimum secondary reaction

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献 19

相关文章 15

编辑推荐

Metrics

本文评价

[1]	陈杰, 林永胜, 肖恺, 杨臣, 邱挺. 胆碱基碱性离子液体催化合成仲丁醇性能研究[J]. 化工学报, 2023, 74(9): 3716-3730.
[2]	郑玉圆, 葛志伟, 韩翔宇, 王亮, 陈海生. 中高温钙基材料热化学储热的研究进展与展望[J]. 化工学报, 2023, 74(8): 3171-3192.
[3]	何晓崐, 刘锐, 薛园, 左然. MOCVD生长AlN单晶薄膜的气相和表面化学反应综述[J]. 化工学报, 2023, 74(7): 2800-2813.
[4]	杨峥豪, 何臻, 常玉龙, 靳紫恒, 江霞. 生物质快速热解下行式流化床反应器研究进展[J]. 化工学报, 2023, 74(6): 2249-2263.
[5]	周小文, 杜杰, 张战国, 许光文. 基于甲烷脉冲法的Fe₂O₃-Al₂O₃载氧体还原特性研究[J]. 化工学报, 2023, 74(6): 2611-2623.
[6]	张全碧, 羊依金, 郭旭晶. 芬顿氧化法对利福平制药废水中溶解性有机物的催化降解[J]. 化工学报, 2023, 74(5): 2217-2227.
[7]	张建华, 陈萌萌, 孙雅雯, 彭永臻. 部分短程硝化同步除磷耦合Anammox实现生活污水高效脱氮除磷[J]. 化工学报, 2023, 74(5): 2147-2156.
[8]	张兰河, 赖青燚, 王铁铮, 关潇卓, 张明爽, 程欣, 徐小惠, 贾艳萍. H₂O₂对SBR脱氮效率和污泥性能的影响[J]. 化工学报, 2023, 74(5): 2186-2196.
[9]	王泽栋, 石至平, 刘丽艳. 考虑气泡非均匀耗散的矩形反应器声流场数值模拟及结构优化[J]. 化工学报, 2023, 74(5): 1965-1973.
[10]	禹进, 余彬彬, 蒋新生. 一种基于虚拟组分的燃烧调控化学作用量化及分析方法研究[J]. 化工学报, 2023, 74(3): 1303-1312.
[11]	付家崴, 陈帅帅, 方凯伦, 蒋新. 微反应器共沉淀反应制备铜锰催化剂[J]. 化工学报, 2023, 74(2): 776-783.
[12]	杨星宇, 马优, 朱春英, 付涛涛, 马友光. 梳状并行微通道内液液分布规律研究[J]. 化工学报, 2023, 74(2): 698-706.
[13]	章承浩, 罗京, 张吉松. 微反应器内基于氮氧自由基催化剂连续氧气/空气氧化反应的研究进展[J]. 化工学报, 2023, 74(2): 511-524.
[14]	张梦波, 楼琳瑾, 冯艺荣, 郑雨婷, 张浩淼, 王靖岱, 阳永荣. 烷基铝氧烷合成技术研究进展[J]. 化工学报, 2023, 74(2): 525-534.
[15]	谢煜, 张民, 胡卫国, 王玉军, 骆广生. 利用膜分散微反应器高效溶解D-7-ACA的研究[J]. 化工学报, 2023, 74(2): 748-755.