楔形中心和偏心料仓中壁面摩擦系数对卸料速率的影响

doi:10.11949/j.issn.0438-1157.20141434

化工学报 ›› 2015, Vol. 66 ›› Issue (3): 880-887.DOI: 10.11949/j.issn.0438-1157.20141434

楔形中心和偏心料仓中壁面摩擦系数对卸料速率的影响

许鹏凯, 段学志, 钱刚, 周兴贵

华东理工大学化学工程联合国家重点实验室, 上海 200237

收稿日期:2014-09-23 修回日期:2014-11-04 出版日期:2015-03-05 发布日期:2015-03-05
通讯作者: 周兴贵
基金资助:
国家重点基础研究发展计划项目(2012CB720501)。

Granular discharge from concentric and eccentric wedge shaped hoppers: effect of wall friction coefficient on discharge rate

XU Pengkai, DUAN Xuezhi, QIAN Gang, ZHOU Xinggui

State Key Laboratory of Chemical Engineering, East China University of Science and Technology, Shanghai 200237, China

Received:2014-09-23 Revised:2014-11-04 Online:2015-03-05 Published:2015-03-05
Supported by:
supported by the National Basic Research Program of China (2012CB720501).

摘要/Abstract

摘要：

采用离散元方法(DEM)研究了在不同的内摩擦系数、料仓半锥角和料仓宽度条件下,楔形中心料仓和偏心料仓中壁面摩擦系数对卸料速率的影响。研究发现,随着壁面摩擦系数的增加,两种料仓的卸料速率均先降低后稳定。当料仓从中心料仓变为偏心料仓时,壁面摩擦系数对卸料速率的影响程度以及卸料速率停止下降时的壁面摩擦系数的值都增大。随着内摩擦系数的减小或料仓半锥角的增大,壁面摩擦系数对卸料速率的影响程度以及卸料速率停止下降时的壁面摩擦系数的值都逐渐减小。增加料仓宽度能够削弱壁面摩擦系数对卸料速率的影响程度,但并不改变卸料速率停止下降时的壁面摩擦系数的值。

关键词: 颗粒流, 计算机模拟, 实验验证, 卸料速率, 壁面摩擦系数

Abstract:

Particle discharging from concentric and eccentric wedge shaped hoppers with different internal friction coefficients, hopper half angles and hopper widths was simulated by 3D discrete element method (DEM) and the effect of wall friction coefficient on discharging rate were investigated. In general, increasing wall friction coefficient would decrease discharging rate by retarding particle-wall slip, and the effect was more significant in wedge shaped hoppers. The friction coefficient in the convergent section had a stronger effect in reducing discharging rate than that in the vertical section. When internal friction coefficient decreased, or the width of the hopper increased, the retarding effect would decrease and eventually become insignificant.

Key words: granular flow, computer simulation, experimental validation, discharge rate, wall friction coefficient

中图分类号:

TQ018

许鹏凯, 段学志, 钱刚, 周兴贵. 楔形中心和偏心料仓中壁面摩擦系数对卸料速率的影响[J]. 化工学报, 2015, 66(3): 880-887.

XU Pengkai, DUAN Xuezhi, QIAN Gang, ZHOU Xinggui. Granular discharge from concentric and eccentric wedge shaped hoppers: effect of wall friction coefficient on discharge rate[J]. CIESC Journal, 2015, 66(3): 880-887.

参考文献 35

[1]	Goodey R J, Brown C J, Rotter J M. Verification of a 3-dimensional model for filling pressures in square thin-walled silos [J]. Eng. Struct., 2003, 25: 1773-1783
[2]	Vidal P, Gallego E, Guaita M, Ayuga F. Finite element analysis under different boundary conditions of the filling of cylindrical steel silos having an eccentric hopper [J]. J. Constr. Steel Res., 2008, 64: 480-492
[3]	Goodey R J, Brown C J. The influence of the base boundary condition in modelling filling of a metal silo [J]. Comput. Struct., 2004, 82: 567-579
[4]	Zhu H P, Yu A B, Wu Y H. Numerical investigation of steady and unsteady state hopper flows [J]. Powder Technol., 2006, 170: 125-134
[5]	Wojcik M, Enstad G G, Jecmenica M. Numerical calculations of wall pressures and stresses in steel cylindrical silos with concentric and eccentric hoppers [J]. Particul. Sci. Technol., 2003, 21: 247-258
[6]	Ketterhagen W R, Hancock B C. Optimizing the design of eccentric feed hoppers for tablet presses using DEM [J]. Comput. Chem. Eng., 2010, 34: 1072-1081
[7]	Balevi?ius R, Ka?ianauskas R, Mroz Z, Sielamowicz I. Discrete element method applied to multiobjective optimization of discharge flow parameters in hoppers [J]. Struct. Multidiscip. O., 2006, 31: 163-175
[8]	Zhu H P, Zhou Z Y, Yang R Y, Yu A B. Discrete particle simulation of particulate systems: a review of major applications and findings [J]. Chem. Eng. Sci., 2008, 63: 5728-5770
[9]	Vidyapati V, Subramaniam S. Granular flow in silo discharge: discrete element method simulations and model assessment [J]. Ind. Eng. Chem. Res., 2013, 52: 13171-13182
[10]	Anand A, Curtis J S, Wassgren C R, Hancock B C, Ketterhagen W R. Predicting discharge dynamics from a rectangular hopper using the discrete element method (DEM) [J]. Chem. Eng. Sci., 2008, 63: 5821-5830
[11]	Nedderman R M, Tüzün U, Savage S B, Houlsby G T. The flow of granular materials (Ⅰ): Discharge rates from hoppers [J]. Chem. Eng. Sci., 1982, 37: 1597-1609
[12]	Weir G J. A mathematical model for dilating, non-cohesive granular flows in steep-walled hoppers [J]. Chem. Eng. Sci., 2004, 59: 149-161
[13]	Balevi?ius R, Ka?ianauskas R, Mróz Z, Sielamowicz I. Discrete-particle investigation of friction effect in filling and unsteady/steady discharge in three-dimensional wedge-shaped hopper [J]. Powder Technol., 2008, 187: 159-174
[14]	Langston P A, Nikitidis M S, Tüzün U, Heyes D M, Spyrou N M. Microstructural simulation and imaging of granular flows in two- and three-dimensional hoppers [J]. Powder Technol., 1997, 94: 59-72
[15]	Kruggel-Emden H, Rickelt S, Wirtz S, Scherer V. A numerical study on the sensitivity of the discrete element method for hopper discharge [J]. J. Press. Ves-T ASME , 2009, 131: 031211
[16]	Vivanco F, Rica S, Melo F. Dynamical arching in a two dimensional granular flow [J]. Granular Matter., 2012, 14: 563-576
[17]	Brown R L, Richards J C. Kinematics of the flow of dry powders and bulk solids [J]. Rheol. Acta, 1965, 4: 153-165
[18]	Laforge R M, Boruff B K. Profiling flow of particles through hopper openings [J]. Ind. Eng. Chem., 1964, 56: 42-46
[19]	Zhu H P, Yu A B. Steady-state granular flow in a 3D cylindrical hopper with flat bottom: macroscopic analysis [J]. Granular Matter, 2005, 7: 97-107
[20]	Wu Jintao (武锦涛), Chen Jizhong (陈纪忠), Yang Yongrong (阳永荣). Microscopic analysis of particle flow in moving bed [J]. J. Zhejiang Univ.: Eng. Sci. (浙江大学学报:工学版), 2006, 40: 864-871
[21]	Wu J, Binbo J, Chen J, Yang Y. Multi-scale study of particle flow in silos [J]. Adv. Powder Technol., 2009, 20: 62-73
[22]	Xu Y, Kafui K D, Thornton C. Silo discharge simulations with different particle properties using the distinct element method [J]. T. Chinese Soc. Agr. Eng. (农业工程学报), 1999, 15: 65-69
[23]	Ketterhagen W R, Curtis J S, Wassgren C R, Hancock B C. Predicting the flow mode from hoppers using the discrete element method [J]. Powder Technol., 2009, 195: 1-10
[24]	Yang S C, Hsiau S S. The simulation and experimental study of granular materials discharged from a silo with the placement of inserts [J]. Powder Technol., 2001, 120: 244-255
[25]	Balevi?ius R, Sielamowicz I, Mróz Z, Ka?ianauskas R. Investigation of wall stress and outflow rate in a flat-bottomed bin: a comparison of the DEM model results with the experimental measurements [J]. Powder Technol., 2011, 214: 322-336
[26]	Majmudar T S, Behringer R P. Contact force measurements and stress-induced anisotropy in granular materials [J]. Nature, 2005, 435: 1079-1082
[27]	Delannay R, Louge M, Richard P, Taberlet N, Valance A. Towards a theoretical picture of dense granular flows down inclines [J]. Nature, 2007, 6: 99-108
[28]	Cundall P A, Strack O D L. A discrete numerical model for granular assemblies [J]. Geotechnique, 1979, 29: 47-65
[29]	Asmar B N, Langston P A, Matchett A J, Walters J K. Validation tests on a distinct element model of vibrating cohesive particle systems [J]. Comput. Chem. Eng., 2002, 26: 785-802
[30]	González-Montellano C, Ramírez Á, Gallego E, Ayuga F. Validation and experimental calibration of 3D discrete element models for the simulation of the discharge flow in silos [J]. Chem. Eng. Sci., 2011, 66: 5116-5126
[31]	Yu Y, Saxén H. Discrete element method simulation of properties of a 3D conical hopper with mono-sized spheres [J]. Adv. Powder Technol., 2011, 22: 324-331
[32]	Masson S, Martinez J. Effect of particle mechanical properties on silo flow and stresses from distinct element simulations [J]. Powder Technol., 2000, 109: 164-178
[33]	Barreto D, O'Sullivan C. The influence of inter-particle friction and the intermediate stress ratio on soil response under generalised stress conditions [J]. Granular Matter, 2012, 14:1-17
[34]	Wang D, Zhou Y. Statistics of contact force network in dense granular matter [J]. Particuology, 2010, 8: 133-140
[35]	Chou C S, Chen R Y. The static and dynamic wall stresses in a circulatory two-dimensional wedge hopper [J]. Adv. Powder Technol., 2003, 14: 195-213

楔形中心和偏心料仓中壁面摩擦系数对卸料速率的影响

Granular discharge from concentric and eccentric wedge shaped hoppers: effect of wall friction coefficient on discharge rate

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献 35

相关文章 15

编辑推荐

Metrics

本文评价

[1]	陈哲文, 魏俊杰, 张玉明. 超临界水煤气化耦合SOFC发电系统集成及其能量转化机制[J]. 化工学报, 2023, 74(9): 3888-3902.
[2]	刘远超, 关斌, 钟建斌, 徐一帆, 蒋旭浩, 李耑. 单层XSe₂（X=Zr/Hf）的热电输运特性研究[J]. 化工学报, 2023, 74(9): 3968-3978.
[3]	闫琳琦, 王振雷. 基于STA-BiLSTM-LightGBM组合模型的多步预测软测量建模[J]. 化工学报, 2023, 74(8): 3407-3418.
[4]	文兆伦, 李沛睿, 张忠林, 杜晓, 侯起旺, 刘叶刚, 郝晓刚, 官国清. 基于自热再生的隔壁塔深冷空分工艺设计及优化[J]. 化工学报, 2023, 74(7): 2988-2998.
[5]	邵远哲, 赵忠盖, 刘飞. 基于共同趋势模型的非平稳过程质量相关故障检测方法[J]. 化工学报, 2023, 74(6): 2522-2537.
[6]	刘尚豪, 贾胜坤, 罗祎青, 袁希钢. 基于梯度提升决策树的三组元精馏流程结构最优化[J]. 化工学报, 2023, 74(5): 2075-2087.
[7]	罗来明, 张劲, 郭志斌, 王海宁, 卢善富, 相艳. 1~5 kW高温聚合物电解质膜燃料电池堆的理论模拟与组装测试[J]. 化工学报, 2023, 74(4): 1724-1734.
[8]	许文烜, 江锦波, 彭新, 门日秀, 刘畅, 彭旭东. 宽速域三种典型型槽油气密封泄漏与成膜特性对比研究[J]. 化工学报, 2023, 74(4): 1660-1679.
[9]	刘潜, 张香兰, 李志平, 李玉龙, 韩梦醒. 油酚分离过程低共熔溶剂的筛选及萃取性能研究[J]. 化工学报, 2022, 73(9): 3915-3928.
[10]	袁妮妮, 郭拓, 白红存, 何育荣, 袁永宁, 马晶晶, 郭庆杰. 化学链燃烧过程Fe₂O₃/Al₂O₃载氧体表面CH₄反应：ReaxFF-MD模拟[J]. 化工学报, 2022, 73(9): 4054-4061.
[11]	黄陆月, 刘畅, 许勇毅, 邢浩若, 王峰, 马双忱. CDI二维浓度传质模型的建立以及实验验证[J]. 化工学报, 2022, 73(7): 2933-2943.
[12]	陈泉, 郑泽希, 李然, 孙其诚, 杨晖. 散斑能见度光谱法测量筒仓内颗粒流的颗粒温度[J]. 化工学报, 2022, 73(6): 2603-2611.
[13]	杨晖, 李宏泽, 陈泉, 郑泽希, 李然, 孙其诚. 从质量流向漏斗流转变过程中的动力学分析[J]. 化工学报, 2022, 73(6): 2722-2731.
[14]	侯起旺, 文兆伦, 张忠林, 刘叶刚, 杨景轩, 陈东良, 郝晓刚, 官国清. 一种煤基多联产碳循环系统的设计及评价[J]. 化工学报, 2022, 73(5): 2073-2082.
[15]	刘薇薇, 崔国民, 张璐, 肖媛, 杨其国, 张冠华. 一种应用于换热网络综合的阻尼优化方法[J]. 化工学报, 2022, 73(5): 2060-2072.