竖直平板间液桥形状的观测与预测模型开发

doi:10.11949/j.issn.0438-1157.20151707

化工学报 ›› 2016, Vol. 67 ›› Issue (6): 2224-2229.DOI: 10.11949/j.issn.0438-1157.20151707

竖直平板间液桥形状的观测与预测模型开发

庄大伟, 杨艺菲, 胡海涛, 丁国良

上海交通大学制冷与低温工程研究所, 上海 200240

收稿日期:2015-11-11 修回日期:2016-02-16 出版日期:2016-06-05 发布日期:2016-06-05
通讯作者: 丁国良
基金资助:
国家自然科学基金项目(51576122);国家自然科学基金创新研究群体科学基金项目(51521004)。

Visualization and prediction model on shape of liquid bridge

ZHUANG Dawei, YANG Yifei, HU Haitao, DING Guoliang

Institute of Refrigeration & Cryogenics Engineering, Shanghai Jiao Tong University, Shanghai 200240, China

Received:2015-11-11 Revised:2016-02-16 Online:2016-06-05 Published:2016-06-05
Supported by:
supported by the National Natural Science Foundation of China (51576122) and the Foundation for Innovative Research Groups of the National Natural Science Foundation of China (51521004).

摘要/Abstract

摘要：

了解析湿工况下液桥对管翅式换热器性能的影响,需要对液桥形状进行实验研究并建立描述液桥形状的方法。通过搭建可视化实验台观察了液桥在竖直平板间的形状,并测量了液桥的接触线和接触角。实验研究了不同体积、不同平板间距、不同平板材料间形成的液桥,并通过实验数据开发了能够描述液桥形状的关联式,包括接触线伸长比和接触角分别与Bond数的关联式。还根据关联式建立了描述液桥形状的方法并将结果与实验数据进行对比,对比结果显示接触线的描述方法平均误差为3.4%,接触角的描述方法平均误差为7.9%。

关键词: 液桥形状, 接触角, 预测, 模型, 实验验证

Abstract:

Water bridge can affect the performance of fin-and-tube heat exchanger working under dehumidifying. In order to know the influence of water bridge on heat exchanger, the shape of water bridge needs to be studied. In this research, a visual experiment was used to develop the prediction model of water bridge shape. Based on the visual experiment, the contact line and the contact angles of water bridge were measured, covering various water volumes, solid plate separations and five different solid materials. The prediction model of contact line via correlated aspect ratio was developed, and the prediction model of contact angles via the correlated maximum and minimum contact angles was proposed. The mean deviation of aspect ratio of contact line was 3.4% and that of contact angles was 7.9%.

Key words: water bridge shape, contact angle, prediction, model, experimental validation

中图分类号:

TK124

庄大伟, 杨艺菲, 胡海涛, 丁国良. 竖直平板间液桥形状的观测与预测模型开发[J]. 化工学报, 2016, 67(6): 2224-2229.

ZHUANG Dawei, YANG Yifei, HU Haitao, DING Guoliang. Visualization and prediction model on shape of liquid bridge[J]. CIESC Journal, 2016, 67(6): 2224-2229.

参考文献 21

[1]	WANG C C, LEE W S, SHEU W J, et al. Investigation of the airside performance of the slit fin-and-tube heat exchangers [J]. International Journal of Refrigeration, 1999, 22(8): 595-603.
[2]	刘金平, 戴绍碧, 叶立平. 析湿工况下波纹翅片管换热器空气侧换热与压降特性 [J]. 化工学报, 2009, 60(10): 2438-2445. LIU J P, DAI S B, YE L P. Air-side heat transfer and friction characteristics of wavy fin-and-tube heat exchangers under dehumidifying conditions [J]. CIESC Journal, 2009, 60(10): 2438-2445.
[3]	COMINI G, NONINO C, SAVINO S. Modeling of conjugate conduction and heat and mass convection in tube-fin exchangers [J]. International Journal of Numerical Methods for Heat and Fluid Flow, 2008, 18(7/8): 954-968.
[4]	杨艺菲, 庄大伟, 胡海涛, 等. 湿工况下平翅片平面凝水形成及运动过程的数值模拟与实验验证 [J]. 化工学报, 2014, 65(S2): 140-147. YANG Y F, ZHUANG D W, HU H T, et al. Numerical simulation and experimental validation of water condensing and moving on plain-fin surface under dehumidifying conditions [J]. CIESC Journal, 2014, 65(S2): 140-147.
[5]	WANG C C,LIN Y T, LEE C J. An airside correlation for plain fin-and-tube heat exchangers in wet conditions [J]. International Journal of Heat and Mass Transfer, 2000, 43(10): 1869-1872.
[6]	李娬, 李慧珍, 康海军, 等. 析湿正弦波纹翅片管束的热质交换特性研究 [J]. 西安交通大学学报, 1996, 30(8): 57-63. LI B, LI H Z, KANG H J, et al. Experimental study on heat/mass transfer and pressure drop for dehumidifying sinusoid fin-and-tube heat exchanger [J]. Journal of Xi'an Jiaotong University, 1996, 30(8): 57-63.
[7]	YUN R, KIM Y B, KIM Y C. Air side heat transfer characteristics of plate finned tube heat exchangers with slit fin configuration under wet conditions [J]. Applied Thermal Engineering, 2009, 29(14/15): 3014-3020.
[8]	MA X K, DING G L, ZHANG Y M, et al. Airside heat transfer and friction characteristics for enhanced fin-and-tube heat exchanger with hydrophilic coating under wet conditions [J]. International Journal of Refrigeration, 2007, 30(7): 1153-1167.
[9]	郭轶波, 杜志敏, 陈萍, 等. 入口相对湿度对开缝翅片管换热器空气侧换热与压降特性的影响 [J]. 化工学报, 2010, 61(S2): 49-53. GUO Y B, DU Z M, CHEN P, et al. Effect of inlet air relative humidity on air side characteristics of slit fin-tube heat exchangers [J]. CIESC Journal, 2010, 61(S2): 49-53.
[10]	ZHUANG D W, HU H T, DING G L, et al. Numerical model for liquid droplet motion on vertical plain-fin surface [J]. HVAC and R Research, 2014, 20(3): 332-343.
[11]	马小魁, 丁国良, 张圆明. 析湿工况下带亲水层开缝翅片管换热器空气侧传热传质特性 [J]. 化工学报, 2007, 58(8): 1911-1916. MA X K, DING G L, ZHANG Y M. Airside heat and mass transfer characteristics of split fin-and-tube heat exchangers under dehumidifying conditions [J]. Journal of Chemical Industry and Engineering(China), 2007, 58(8): 1911-1916.
[12]	MIN J C, WEBB R L. Condensate carryover phenomena in dehumidifying finned-tube heat exchangers [J]. Experimental Thermal and Fluid Science, 2000, 22(3/4): 175-182.
[13]	WANG C C, HSIEH Y C, LIN Y T. Performance of plate finned tube heat exchangers under dehumidifying conditions [J]. Journal of Heat Transfer, 1997; 119(1):109-17.
[14]	VERGES M A, LARSON M C, BACOU R. Force and shapes of liquid bridges between circular pads [J]. Experimental Mechanics, 2001, 41(4): 351-357.
[15]	FERRERA C, CABEZAS M G, MONTANERO J M. An experimental analysis of the linear vibration of axisymmetric liquid bridges [J]. Physics of Fluids, 2006, 18(8): 082105.
[16]	ZHANG F Y, YANG X G, WANG C Y. Liquid water removal from a polymer electrolyte fuel cell [J]. Journal of the Electrochemical Society, 2006, 153(2): A225-A232.
[17]	CHEN H, TANG T, AMIRFAZLI A. Effect of contact angle hysteresis on breakage of a liquid bridge [J]. European Physical Journal: Special Topics, 2015, 224(2): 277-288.
[18]	VOGEL T I. Stability of a liquid drop trapped between two parallel planes(Ⅱ): General contact angles [J]. SIAM Journal on Applied Mathematics, 1989, 49(4): 1009-1028.
[19]	ACERO F J, FERRERA C, CABEZAS M G, et al. Liquid bridge equilibrium contours between non-circular supports [J]. Microgravity Science and Technology, 2005, 17(2): 18-30.
[20]	VOGEL T I. Stability of a liquid drop trapped between two parallel planes [J]. SIAM Journal on Applied Mathematics, 1987, 47(3): 516-525.
[21]	CHEN H, TANG T, AMIRFAZLI A. Modeling liquid bridge between surfaces with contact angle hysteresis [J]. Langmuir, 2013, 29(10): 3310-3319.

竖直平板间液桥形状的观测与预测模型开发

Visualization and prediction model on shape of liquid bridge

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献 21

相关文章 15

编辑推荐

Metrics

本文评价

[1]	宋嘉豪, 王文. 斯特林发动机与高温热管耦合运行特性研究[J]. 化工学报, 2023, 74(S1): 287-294.
[2]	连梦雅, 谈莹莹, 王林, 陈枫, 曹艺飞. 地下水预热新风一体化热泵空调系统制热性能研究[J]. 化工学报, 2023, 74(S1): 311-319.
[3]	金正浩, 封立杰, 李舒宏. 氨水溶液交叉型再吸收式热泵的能量及分析[J]. 化工学报, 2023, 74(S1): 53-63.
[4]	王浩, 王振雷. 基于自适应谱方法的裂解炉烧焦模型化简策略[J]. 化工学报, 2023, 74(9): 3855-3864.
[5]	李科, 文键, 忻碧平. 耦合蒸气冷却屏的真空多层绝热结构对液氢储罐自增压过程的影响机制研究[J]. 化工学报, 2023, 74(9): 3786-3796.
[6]	尹刚, 李伊惠, 何飞, 曹文琦, 王民, 颜非亚, 向禹, 卢剑, 罗斌, 卢润廷. 基于KPCA和SVM的铝电解槽漏槽事故预警方法[J]. 化工学报, 2023, 74(8): 3419-3428.
[7]	李锦潼, 邱顺, 孙文寿. 煤浆法烟气脱硫中草酸和紫外线强化煤砷浸出过程[J]. 化工学报, 2023, 74(8): 3522-3532.
[8]	于旭东, 李琪, 陈念粗, 杜理, 任思颖, 曾英. 三元体系KCl + CaCl₂ + H₂O 298.2、323.2及348.2 K相平衡研究及计算[J]. 化工学报, 2023, 74(8): 3256-3265.
[9]	诸程瑛, 王振雷. 基于改进深度强化学习的乙烯裂解炉操作优化[J]. 化工学报, 2023, 74(8): 3429-3437.
[10]	闫琳琦, 王振雷. 基于STA-BiLSTM-LightGBM组合模型的多步预测软测量建模[J]. 化工学报, 2023, 74(8): 3407-3418.
[11]	郭雨莹, 敬加强, 黄婉妮, 张平, 孙杰, 朱宇, 冯君炫, 陆洪江. 稠油管道水润滑减阻及压降预测模型修正[J]. 化工学报, 2023, 74(7): 2898-2907.
[12]	刘春雨, 周桓宇, 马跃, 岳长涛. CaO调质含油污泥干燥特性及数学模型[J]. 化工学报, 2023, 74(7): 3018-3027.
[13]	李艳辉, 丁邵明, 白周央, 张一楠, 于智红, 邢利梅, 高鹏飞, 王永贞. 非常规服役超临界锅炉的微纳尺度腐蚀动力学模型建立及应用[J]. 化工学报, 2023, 74(6): 2436-2446.
[14]	于源, 陈薇薇, 付俊杰, 刘家祥, 焦志伟. 几何相似涡流空气分级机环形区流场变化规律研究及预测[J]. 化工学报, 2023, 74(6): 2363-2373.
[15]	刘起超, 周云龙, 陈聪. 起伏振动垂直上升管气液两相流截面含气率分析与计算[J]. 化工学报, 2023, 74(6): 2391-2403.