硅橡胶在模拟PEM燃料电池环境下的损伤机理

doi:10.3969/j.issn.0438-1157.2014.09.049

化工学报 ›› 2014, Vol. 65 ›› Issue (9): 3669-3675.DOI: 10.3969/j.issn.0438-1157.2014.09.049

硅橡胶在模拟PEM燃料电池环境下的损伤机理

李果¹, 谈金祝², 巩建鸣², 贾文华¹

1 南京工程学院机械工程学院, 江苏南京 211167;
2 南京工业大学机械与动力工程学院, 江苏南京 211816

收稿日期:2014-01-07 修回日期:2014-05-30 出版日期:2014-09-05 发布日期:2014-09-05
通讯作者: 李果
基金资助:
南京工程学院引进人才科研启动基金项目（YKJ201304）；江苏省自然科学青年基金项目（SBK201343507）；江苏省高校自然科学基金项目（13KJB460009）；南京工程学院青年基金项目（QKJA201201）。

Degradation mechanism of silicone rubber in simulated PEM fuel cell environment

LI Guo¹, TAN Jinzhu², GONG Jianming², JIA Wenhua¹

1 School of Mechanical Engineering, Nanjing Institute of Technology, Nanjing 211167, Jiangsu, China;
2 School of Mechanical and Power Engineering, Nanjing University of Technology, Nanjing 211816, Jiangsu, China

Received:2014-01-07 Revised:2014-05-30 Online:2014-09-05 Published:2014-09-05
Supported by:
supported by the Research Foundation for Talented Scholars of Nanjing Institute of Technology (YKJ201304), the Natural Science Foundation of Jiangsu Province (SBK201343507), the Natural Science Fund of Colleges and Universities of Jiangsu Province (13KJB460009) and the Research Foundation for Talented Scholars of Nanjing Institute of Technology (QKJA201201).

摘要/Abstract

摘要： 弹性体材料垫片作为PEM燃料电池中一个重要构件，长期服役在PEM燃料电池潮湿、偏酸性环境下，其化学损伤过程是如何演变的对于研究垫片材料的机械密封性能、预测垫片材料的寿命起着基础性作用。采用先进材料测试分析方法XPS技术研究了弹性体材料在模拟的燃料电池环境中的化学降解过程，从分子角度揭示了材料化学损伤的机理主要是材料分子主链的断裂、侧链的断裂及交联区的水解。

关键词: 硅橡胶, 燃料电池, 降解, 力学性能, XPS

Abstract: Elastomer material gasket as an important component works in proton exchange membrane (PEM) fuel cell under moist, acidic conditions. The evolution process of the material's chemical degradation plays a fundamental role in studying the performance of mechanical seal gasket material and its life prediction. The chemical process of the elastomer material was analyzed by using X-ray photoelectron spectroscopy (XPS). The degradation mechanism was mainly molecular chain scission in the backbone and side chain and hydrolysis of crosslinking.

Key words: silicone rubber, fuel cell, degradation, mechanical properties, XPS

中图分类号:

TK91

李果, 谈金祝, 巩建鸣, 贾文华. 硅橡胶在模拟PEM燃料电池环境下的损伤机理[J]. 化工学报, 2014, 65(9): 3669-3675.

LI Guo, TAN Jinzhu, GONG Jianming, JIA Wenhua. Degradation mechanism of silicone rubber in simulated PEM fuel cell environment[J]. CIESC Journal, 2014, 65(9): 3669-3675.

参考文献 20

[1]	Wang Feijie (汪飞杰), Yang Daijun (杨代军), Zhang Hao (张浩), Ma Jianxin (马建新). Response features of a 1.5 kW proton exchange membrane fuel cell stack for dynamic cycle [J]. CIESC Journal (化工学报), 2013, 64 (4): 1380-1386
[2]	Wang Xiaoshan (汪小姗), Zhang Jinfang (张锦芳), Zhang Caizhi (张财智), Han Ming (韩明). Experiment of pulsation hydrogen passing into PEMFC [J]. CIESC Journal (化工学报), 2012, 63 (1): 237-243
[3]	Xiao Yu (肖宇), Ming Pingwen (明平文), Yi Baolian (衣宝廉). Characteristics of liquid droplet motion at gas diffusion layer/gas flow channel interface in PEM fuel cells [J]. Journal of Chemical Industry and Engineering (China) (化工学报), 2008, 59 (8): 2089-2094
[4]	Du Chunyu (杜春雨), Shi Pengfei (史鹏飞), Cheng Xinqun (程新群), Yin Geping (尹鸽平). Effective proton conductivity of catalyst layers in proton exchange membrane fuel cells [J]. Journal of Chemical Industry and Engineering (China) (化工学报), 2005, 56 (6): 1102-1105
[5]	Hu Jun (胡军), Yi Baolian (衣宝廉), Hou Zhongjun (候中军), Cai Yinghua (才英华), Zhang Huamin (张华民). Numerical simulation of proton exchange membrane fuel cell cathode with conventional flow field (Ⅱ): Analysis of influence on performance of PEMFCs [J]. Journal of Chemical Industry and Engineering (China) (化工学报), 2004, 55 (1): 96-100
[6]	Tu Haitao (涂海涛), Sun Wence (孙文策), Xie Maozhao (解茂昭), Abuliti (阿布里提). Three-dimensional analysis of two-layer gas diffusion layer characteristics of proton exchange membrane fuel cell [J]. Journal of Chemical Industry and Engineering (China) (化工学报), 2008, 59 (1): 182-188
[7]	Youn Bok-Hee, Huh Chan-Su. Surface degradation of HTV silicone rubber and EPDM used for outdoor insulators under accelerated ultraviolet weathering condition [J]. IEEE Transactions on Dielectrics and Electrical Insulation, 2005, 12 (5): 1015-1024
[8]	Graiver D, Farminer K W, Narayan R. A review of the fate and effects of silicones in the environment [J]. Journal of Polymers and the Environment, 2003, 11 (4): 129-136
[9]	Mitra S, Ghanbari-siahkali A, Kingshott P, Kristoffer A, Rehmeier H K, Christensen A G. Chemical degradation of an uncrosslinked pure fluororubber in an alkaline environment [J]. Journal of Polymer Science Part A: Polymer Chemistry, 2004, 83: 195-206
[10]	Mitra S, Ghanbari-siahkali A, Kingshott P, Pehmeier H K, Abildgaard H, Kristoffer A. Chemical degradation of crosslinked ethylene-propylene-diene rubber in an acidic environment (Ⅰ): Effect on accelerated sulphur crosslinks [J]. Polymer Degradation and Stability, 2006, 91 (1): 69-80
[11]	Mitra S, Ghanbari-siahkali A, Kingshott P, Pehmeier H K, Abildgaard H, Kristoffer A. Chemical degradation of crosslinked ethylene-propylene-diene rubber in an acidic environment (Ⅱ): Effect of peroxide crosslinking in the presence of a coagent [J]. Polymer Degradation and Stability, 2006, 91 (1): 81-93
[12]	Lin C W, Chien C H, Tan J, Chao Y J, van Zee J W. Chemical degradation of five elastomeric seal materials in a simulated and an accelerated PEM fuel cell environment [J]. Journal of Power Sources, 2011, 196 (4): 1955-1966
[13]	Tan J, Chao Y J, Wang H, Gong J M, van Zee J W. Chemical and mechanical stability of EPDM in a PEM fuel cell environment [J]. Polym. Degrad. Stab., 2009, 94 (11): 2072-2078
[14]	Tan J, Chao Y J, van Zee J W, Li X, Wang X, Yang M. Assessment of mechanical properties of fluoroelastomer and EPDM in a simulated PEM fuel cell environment by microindentation test [J]. Mater. Sci. Eng. A., 2008, 496: 464-470
[15]	Tan Jinzhu, Chao Y J, Yang M, Williams C T, van Zee J W. Degradation characteristics of elastomeric gasket materials in a simulated PEM fuel cell environment [J]. Journal of Materials Engineering and Performance, 2008, 17 (6): 785-792
[16]	Tan Jinzhu, Chao Y J, Li X, van Zee J W. Degradation of silicone rubber under compression in a simulated PEM fuel cell environment [J]. Journal of Power Sources, 2007, 172 (2): 782-789
[17]	Tan J, Chao Y J, van Zee J W, Lee W K. Degradation of elastomeric gasket materials in PEM fuel cells [J]. Mater. Sci. Eng. A., 2007, 445/446: 669-675
[18]	Zhang Bin (张滨), Sun Yuzhen (孙玉珍), Wang Wenhao (王文皓). Line shapes used in XPS and background subtraction [J]. Physics Examination and Testing (物理测试), 2011 (1): 18-23
[19]	Hesse R, Streubel P, Szargan R. Product or sum: comparative tests of Voigt, and product or sum of Gaussian and Lorentzian functions in the fitting of synthetic Voigt-based X-ray photoelectron spectra [J]. Surface and Interface Analysis, 2007, 39 (5): 381-391
[20]	Moulder J F, Stickle W F, Sobol P E, et al. Handbook of X-ray Photoelectron [M]. Minnesota: PerkineElmer Press, 1992

硅橡胶在模拟PEM燃料电池环境下的损伤机理

Degradation mechanism of silicone rubber in simulated PEM fuel cell environment

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献 20

相关文章 15

编辑推荐

Metrics

本文评价

[1]	陈哲文, 魏俊杰, 张玉明. 超临界水煤气化耦合SOFC发电系统集成及其能量转化机制[J]. 化工学报, 2023, 74(9): 3888-3902.
[2]	杨百玉, 寇悦, 姜峻韬, 詹亚力, 王庆宏, 陈春茂. 炼化碱渣湿式氧化预处理过程DOM的化学转化特征[J]. 化工学报, 2023, 74(9): 3912-3920.
[3]	李艺彤, 郭航, 陈浩, 叶芳. 催化剂非均匀分布的质子交换膜燃料电池操作条件研究[J]. 化工学报, 2023, 74(9): 3831-3840.
[4]	徐文杰, 贾献峰, 王际童, 乔文明, 凌立成, 王任平, 余子舰, 张寅旭. 有机硅/酚醛杂化气凝胶的制备和性能研究[J]. 化工学报, 2023, 74(8): 3572-3583.
[5]	刘杰, 吴立盛, 李锦锦, 罗正鸿, 周寅宁. 含乙烯基胺酯键聚醚类可逆交联聚合物的制备及性能研究[J]. 化工学报, 2023, 74(7): 3051-3057.
[6]	杨琴, 秦传鉴, 李明梓, 杨文晶, 赵卫杰, 刘虎. 用于柔性传感的双形状记忆MXene基水凝胶的制备及性能研究[J]. 化工学报, 2023, 74(6): 2699-2707.
[7]	李瑞康, 何盈盈, 卢维鹏, 王园园, 丁皓东, 骆勇名. 电化学强化钴基阴极活化过一硫酸盐的研究[J]. 化工学报, 2023, 74(5): 2207-2216.
[8]	罗来明, 张劲, 郭志斌, 王海宁, 卢善富, 相艳. 1~5 kW高温聚合物电解质膜燃料电池堆的理论模拟与组装测试[J]. 化工学报, 2023, 74(4): 1724-1734.
[9]	吴学红, 栾林林, 陈亚南, 赵敏, 吕财, 刘勇. 可降解柔性相变薄膜的制备及其热性能[J]. 化工学报, 2023, 74(4): 1818-1826.
[10]	钱志广, 樊越, 王世学, 岳利可, 王金山, 朱禹. 吹扫条件对PEMFC阻抗弛豫现象和低温启动的影响[J]. 化工学报, 2023, 74(3): 1286-1293.
[11]	王帅, 杨富凯, 徐新宇. 阻燃型全生物基多元醇聚氨酯泡沫的制备及性能研究[J]. 化工学报, 2023, 74(3): 1399-1408.
[12]	刘海芹, 李博文, 凌喆, 刘亮, 俞娟, 范一民, 勇强. 羟基-炔点击化学改性半乳甘露聚糖薄膜的制备及性能研究[J]. 化工学报, 2023, 74(3): 1370-1378.
[13]	赵亚静, 胡激江, 介素云, 李伯耿. HTPB引入方式对不饱和树脂改性效果的影响[J]. 化工学报, 2023, 74(2): 883-892.
[14]	郑少杰, 王建斌, 胡激江, 李伯耿, 袁文博, 王宗, 姚臻. 单体组成切换法调控聚丙烯/丁烯合金的结构与性能[J]. 化工学报, 2023, 74(2): 904-915.
[15]	陈毓明, 历伟, 严翔, 王靖岱, 阳永荣. 初生态聚乙烯聚集态结构调控研究进展[J]. 化工学报, 2023, 74(2): 487-499.