外环状弹性壁布膜器及超薄降膜厚度

doi:10.3969/j.issn.0438-1157.2013.11.010

化工学报 ›› 2013, Vol. 64 ›› Issue (11): 3949-3955.DOI: 10.3969/j.issn.0438-1157.2013.11.010

外环状弹性壁布膜器及超薄降膜厚度

刘人滔, 郑晓军, 朱家骅, 夏素兰, 王子宁

四川大学化学工程学院, 四川成都 610065

收稿日期:2013-03-27 修回日期:2013-05-29 出版日期:2013-11-05 发布日期:2013-11-05
通讯作者: 朱家骅
作者简介:刘人滔(1988-),男,硕士研究生。
基金资助:
国家自然科学基金项目(21276161);中央高校基本科研专项(2010SCU22008)。

Elastic wall distributor of outer annular falling film and its ultra-thin characteristics

LIU Rentao, ZHENG Xiaojun, ZHU Jiahua, XIA Sulan, WANG Zining

School of Chemical Engineering, Sichuan University, Chengdu 610065, Sichuan, China

Received:2013-03-27 Revised:2013-05-29 Online:2013-11-05 Published:2013-11-05
Supported by:
supported by the National Natural Science Foundation of China(21276161)and the Central University Fundamentals Research Plan(2010SCU22008).

摘要/Abstract

摘要： 研发了竖直管外环状弹性壁降膜分布器,可以产生微米量级厚度均匀的超薄降膜流动。由弹性薄壁轴对称变形协调性决定,该布膜器具有均匀性和稳定性内在机理。理论分析导出了初始膜厚及布膜流量与布膜器内液柱高度的线性关系,并通过布膜器操作参数及降膜流量等实验数据进行了验证。实验结果表明,该布膜器对降膜管壁的润湿性能已经达到由固液界面性质决定的最小润湿流率。

关键词: 弹性壁布膜器, 降膜, 微通道, 最小润湿流率

Abstract: A new type of elastic wall distributor of outer annular falling film was developed.This method could create a uniform annular channel for the micron-size ultra-thin falling film flow,which could be precisely controlled.This distributor had homogeneity and stability of internal mechanism due to the axisymmetrical deformation coordination characteristics of elastic wall and it could generate negative feedback responses to fluid pressure changes sensitively.According to the theory of thin shell and Amonton law of friction,the linear relationship between initial film thickness and liquid height was given.Also,the equation of falling film flow was established.Experiments were performed using water and 30% glycerol aqueous solutions at lower flow rates.The results indicated that the two equations obtained were in good agreement with experimental data and could be used as the design equations for engineering applications. The experiments also revealed that the vertical tube with a length of 0.6 m and a diameter of 14 mm could be completely wetted by the ultra-thin falling film 0.157 mm thick using the elastic wall distributor.And the wetting performance of the distributor reached the dimensionless minimum wetting rate,which was dependent on the properties of the solid-liquid interface.Compared with other liquid distributors,the elastic wall distributor gave the best performance of hydrodynamics.

Key words: elastic wall distributor, falling film, microchannels, minimum wetting rate

中图分类号:

TQ051.6

刘人滔, 郑晓军, 朱家骅, 夏素兰, 王子宁. 外环状弹性壁布膜器及超薄降膜厚度[J]. 化工学报, 2013, 64(11): 3949-3955.

LIU Rentao, ZHENG Xiaojun, ZHU Jiahua, XIA Sulan, WANG Zining. Elastic wall distributor of outer annular falling film and its ultra-thin characteristics[J]. CIESC Journal, 2013, 64(11): 3949-3955.

参考文献 18

[1]	Hartely D E,Murgatroyd W.Criteria for the break-up of thin liquid layers flowing isothermally over solid surface[J].Int.J.Heat Mass Transfer,1964,7:1003-1015
[2]	Hobler T.Minimum surface wetting[J].Chemia Stosowana,1964,2B:145-159
[3]	Morison K R,Worth Q A G,Dea N P O.Minimum wetting and distribution rates in falling film evaporators[J].Trans. IChemE,Part C,Food and Bioproducts Processing,2006,84(C4):302-310
[4]	Haruo Hikita,Kosaku Ishimi,Sadatoshi Koroyasu.Gas desorption from falling liquid films in entrance region of inclined wetted-wall columns with an overflow-type distributor[J].Chemical Engineering Science,1990,45:437-442
[5]	Beccari M,Di Pinto A C,Spinosa L.Liquid film distributors for vertical tube evaporation desalination plants[J].Desalination,1979,29:295-310
[6]	Li Rui(李瑞),Dong Weizhi(董伟志),Shi Xiaoping(史晓平),Zhang Shaofeng(张少峰).Umbrella distributor in falling film evaporation[J].Journal of Chemical Industry and Engineering(China)(化工学报),2002,51(5):699-702
[7]	Luo Chao,Ma Weibin,Gong Yulie.Design of single vertical tube falling film evaporator base on experiment[J].Journal of Loss Prevention in the Process Industries,2011,24:695-698
[8]	Mohamed S,Genk E I,Hamed H Saber.Minimum thickness of a flowing down liquid film on a vertical surface[J].International Journal of Heat and Mass Transfer,2001,44:2809-2825
[9]	Jia Shaoyi(贾绍义),Wu Songhai(吴松海),Li Jie(李杰),Wang Ruolei(王若雷).Influence of surface treatment of polypropylene packing on its wettability and mass transfer performance[J].Journal of Chemical Industry and Engineering(China)(化工学报),2000,51(6):832-835
[10]	Ponter B,Davies G A,Ross T K,Thornley P G.The influence of mass transfer on liquid film breakdown[J].Int.J.Heat Mass Transfer,1967,10:349-359
[11]	Bernardin J D,Mudawar I,Walsh C B,Franses E I.Contact angle temperature dependence for water droplets on practical aluminum surface[J].Int.J.Heat Mass Transfer,1997,40(5):1017-1033
[12]	Wang T,Davison J F,Wilson D I.Effect of surfactant on flow patterns and draining films created by a static horizontal liquid jet impinging on a vertical surface at low flow rates[J].Chemical Engineering Science,2013,88:79-94
[13]	Morison K R,Tandon G.Minimum wetting rates for falling films on stainless steel[J].Developments in Chemical Engineering and Mineral Processing,2006,14(1/2):153-162
[14]	Yu Guocong(余国琮),et al.Chemical Containers and Process Equipment(化工容器及设备)[M].Beijing:Chemical Industry Press,1980:93-94
[15]	Cao Xiaoping(曹晓平),Jiang Yimin(蒋亦民).Frictional property of wetting contact line and Wenzel's behavior of solid surface tension[J].Acta Physica Sinica(物理学报),2005,54(5):2202-2205
[16]	Zhu Jiahua(朱家骅),Xia Sulan(夏素兰),Zhang Fengzhen(张峰榛),Chen Jianli(陈建利),Zheng Xiaojun(郑晓军).The evaporation and crystallization method and apparatus of the phosphoric acid solution under low temperature[P]:ZL,201010202351.2.2013-01-16
[17]	Bird R Byron,Stewart Warren E,Lightfoot Edwin N.Transport Phenomena[M].Beijing:Chemical Industry Press,2002:53-55
[18]	Zheng Xiaojun(郑晓军).Study on countercurrent gas-liquid interface transport characteristics of ultra-thin falling film flow[D].Chengdu:Sichuan University,2013

外环状弹性壁布膜器及超薄降膜厚度

Elastic wall distributor of outer annular falling film and its ultra-thin characteristics

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献 18

相关文章 15

编辑推荐

Metrics

本文评价

[1]	江河, 袁俊飞, 王林, 邢谷雨. 均流腔结构对微细通道内相变流动特性影响的实验研究[J]. 化工学报, 2023, 74(S1): 235-244.
[2]	刘文竹, 云和明, 王宝雪, 胡明哲, 仲崇龙. 基于场协同和耗散的微通道拓扑优化研究[J]. 化工学报, 2023, 74(8): 3329-3341.
[3]	贾露凡, 王艺颖, 董钰漫, 李沁园, 谢鑫, 苑昊, 孟涛. 微流控双水相贴壁液滴流动强化酶促反应研究[J]. 化工学报, 2023, 74(3): 1239-1246.
[4]	张雪婷, 胡激江, 赵晶, 李伯耿. 高分子量聚丙二醇在微通道反应器中的制备[J]. 化工学报, 2023, 74(3): 1343-1351.
[5]	何万媛, 陈一宇, 朱春英, 付涛涛, 高习群, 马友光. 阵列凸起微通道内气液两相传质特性研究[J]. 化工学报, 2023, 74(2): 690-697.
[6]	杨星宇, 马优, 朱春英, 付涛涛, 马友光. 梳状并行微通道内液液分布规律研究[J]. 化工学报, 2023, 74(2): 698-706.
[7]	项星宇, 王忠东, 董艳鹏, 李守川, 朱春英, 马友光, 付涛涛. 微通道内屈服应力型流体的流变特性及多相流研究进展[J]. 化工学报, 2023, 74(2): 546-558.
[8]	盛林, 昌宇, 邓建, 骆广生. 阶梯式T型微通道内有序气泡群的形成和流动特性研究[J]. 化工学报, 2023, 74(1): 416-427.
[9]	侯跃辉, 刘璇, 廉应江, 韩梅, 尧超群, 陈光文. 超声微反应器内三硝基间苯三酚合成工艺研究[J]. 化工学报, 2022, 73(8): 3597-3607.
[10]	董宜放, 于樱迎, 胡学功, 裴刚. 电场对竖直微槽润湿及毛细流动特性影响[J]. 化工学报, 2022, 73(7): 2952-2961.
[11]	许非石, 杨丽霞, 陈光文. 超声微反应器内气液传质过程的介尺度强化机制[J]. 化工学报, 2022, 73(6): 2552-2562.
[12]	王忠东, 朱春英, 马友光, 付涛涛. 并行微通道内液液两相流及介尺度效应[J]. 化工学报, 2022, 73(6): 2563-2572.
[13]	殷亚然, 朱星星, 张先明, 朱春英, 付涛涛, 马友光. 微通道内醇胺/离子液体复配水溶液吸收CO₂的传质特性[J]. 化工学报, 2022, 73(5): 1930-1939.
[14]	王宜飞, 王清强, 姬德生, 李申芳, 金楠, 赵玉潮. 微通道壁面浸润性对气-液两相流的影响规律研究[J]. 化工学报, 2022, 73(4): 1501-1514.
[15]	王小西, 李笑艳, 王保伟. 介质阻挡放电微等离子体分解二氧化碳研究[J]. 化工学报, 2022, 73(3): 1343-1350.