CIESC Journal ›› 2018, Vol. 69 ›› Issue (9): 4001-4011.DOI: 10.11949/j.issn.0438-1157.20180332

Previous Articles     Next Articles

Optimization of electrochemical coupling system process for coking waste water pretreatment by response surface method

SONG Dihui1, AN Luyang1, ZHANG Litao1, ZHANG Yafeng1, XU Xinwei1, WANG Yunan1, WEI Huangzhao2   

  1. 1. Sinosteel Anshan Research Institute of Thermo-energy Company Limited, Anshan 114044, Liaoning, China;
    2. Dalian Institute of Chemical Physics, Chinese Academy of Sciences, Dalian 116023, Liaoning, China
  • Received:2018-03-28 Revised:2018-05-11 Online:2018-09-05 Published:2018-09-05

响应曲面法优化电化学耦合体系预处理焦化废水

宋迪慧1, 安路阳1, 张立涛1, 张亚峰1, 徐歆未1, 王宇楠1, 卫皇曌2   

  1. 1. 中钢集团鞍山热能研究院有限公司, 辽宁 鞍山 114044;
    2. 中国科学院大连化学物理研究所, 辽宁 大连 116023
  • 通讯作者: 安路阳
  • 基金资助:

    科技部科研院所开发专项资金支持项目(2008EG113044)。

Abstract:

The electrochemical coupling system was used on the pretreatment of coking waste water with high organic loading and biological inhibition. The sludge-derived activated carbon(AC) particle electrodes were prepared from in-site sludge and characterized, indicating that surface oxygen groups contained hydroxyl, ether, carbonyl, carboxyl, etc., which could accelerate catalytic reaction. The effects of cathode aeration were investigated and degradation mechanism of organic contaminants was analyzed. The results showed that aeration was beneficial to open-loop reaction. Based on the Central-Composite response surface method, the separate action and interaction effects of impressed voltage, initial pH, aeration rate, and AC filling ratio were evaluated, and COD removal rate was used as the evaluation index. The significance of influencing factors followed the order:AC filling ratio > initial pH > aeration rate > impressed voltage, and the most significant interaction occurred between initial pH and aeration rate. The optimal conditions were determined to be impressed voltage 15 V, pH 5.8, aeration rate 12.4 ml·min-1, AC filling ratio 50%, and reaction time 45 min. Then COD removal rate reached 46.8%. Under optimal conditions, COD of the treated waste water decreased from 4700 mg·L-1 to 2500 mg·L-1, and chroma removal rate was 50% with low energy consumption of 0.971 kW·h·(kg COD)-1. And B/C increased from 0.05 to 0.37, indicating the biochemical properties were improved. Therefore, the electrochemical technique can efficiently pretreat the coking waste water and improve its biodegradability.

Key words: electrochemistry, coking waste water, pretreatment, aeration, activated carbon, Central-Composite response surface method

摘要:

针对焦化废水有机负荷高、生物抑制性强等特点,采用电化学耦合体系进行预处理研究。以原厂污泥制备污泥活性炭(AC)粒子电极,并表征其表面含有羟基、醚基、羰基、羧基等多种含氧官能团,有利于催化反应。考察阴极曝气对预处理的影响及降解机理分析,结果表明曝气有利于开环反应。基于Central-Composite响应曲面法考察外加电压、初始pH、曝气量、AC填充比等因素对预处理的单独影响及交互作用,并以COD去除率为评价指标。结果表明:各因子的影响显著性顺序为AC填充比 > 初始pH > 曝气量 > 外加电压,其中初始pH和曝气量的交互作用较显著。最佳运行条件为外加电压15 V,初始pH 5.8,曝气量12.4 ml·min-1,AC填充比50%,反应时间45 min,此时COD去除率达46.8%。废水COD由4700 mg·L-1降至2500 mg·L-1,色度去除率为50%,B/C由0.05增至0.37,可生化性明显提高,且能耗较低为0.971 kW·h·(kg COD)-1。研究表明,采用电化学技术能有效预处理焦化废水,并提高可生化性。

关键词: 电化学, 焦化废水, 预处理, 曝气, 活性炭, Central-Composite响应曲面法

CLC Number: