泡沫金属对圆管内R410A流动沸腾压降特性的影响

doi:10.3969/j.issn.0438-1157.2012.11.007

化工学报 ›› 2012, Vol. 63 ›› Issue (11): 3428-3433.DOI: 10.3969/j.issn.0438-1157.2012.11.007

泡沫金属对圆管内R410A流动沸腾压降特性的影响

孙硕, 胡海涛, 丁国良, 朱禹

上海交通大学制冷与低温工程研究所, 上海 200240

收稿日期:2012-04-01 修回日期:2012-05-08 出版日期:2012-11-05 发布日期:2012-11-05
通讯作者: 丁国良
作者简介:孙硕(1987-),男,硕士研究生。
基金资助:
国家自然科学基金项目(50906048)。

Influence of metal foams on two-phase pressure drop of R410A flow boiling in circular tubes

SUN Shuo, HU Haitao, DING Guoliang, ZHU Yu

Institute of Refrigeration and Cryogenics, Shanghai Jiao Tong University, Shanghai 200240, China

Received:2012-04-01 Revised:2012-05-08 Online:2012-11-05 Published:2012-11-05
Supported by:
supported by the National Natural Science Foundation of China(50906048).

摘要/Abstract

摘要： 对填充泡沫金属的圆管中R410A流动沸腾的两相流压降特性进行了实验研究。实验对象为两根内径13.8 mm,分别填充5 PPI/95%孔隙率和10 PPI/95%孔隙率的泡沫铜的圆管。实验工况涵盖:蒸发压力995 kPa;质流密度30~90 kg·m^-2·s^-1;热通量5.9~16.5 kW·m^-2;入口干度0.175~0.775。实验结果表明:泡沫金属显著增加制冷剂流动沸腾的压降,在入口干度为0.775,质流密度为90 kg·m^-2·s^-1时,内嵌10 PPI 泡沫金属的圆管中的压降梯度达56 kPa·m^-1;泡沫金属PPI越大,压降增加越多,相同工况下内嵌10 PPI泡沫金属圆管中制冷剂流动沸腾的压降是内嵌5 PPI泡沫金属圆管中的压降的1.2倍左右。根据实验数据开发了适用于填充泡沫金属的内径13.8 mm圆管中的流动沸腾的压降关联式,结果表明90%的预测值与实验值的偏差在±15%以内。

关键词: 泡沫金属, R410A, 流动沸腾, 压降, 关联式

Abstract: The two-phase pressure drop characteristics of R410A flow boiling inside tubes filled with metal foams were investigated experimentally.The test sections are two tubes of 13.8 mm inner diameter filled with 5 PPI/95% porosity and 10 PPI/95% porosity metal foams separately.Experimental conditions include saturation pressure of 995 kPa,mass flux from 30 to 90 kg穖^-2穝^-1,heat flux from 5.9 to 16.5 kW穖^-2,and inlet vapor quality from 0.175 to 0.775.The experimental results are as follows.Metal foams always increase the pressure drop of flow boiling,and the pressure drop reaches 56 kPa穖^-1 at vapor quality of 0.775 and mass flux of 90 kg穖^-2穝^-1. The pressure drop increases with the value of PPI,and the pressure drop with 10 PPI metal foams can be as much as 1.2 times that with 5 PPI metal foams under the same working condition.A pressure drop correlation for the 13.8 mm tube filled with metal foams was developed based on the experimental data,and 90% of the predicted results agree with the experimental data within a deviation of ?15%.

Key words: metal foam, R410A, flow boiling, pressure drop, correlation

中图分类号:

TK124

孙硕, 胡海涛, 丁国良, 朱禹. 泡沫金属对圆管内R410A流动沸腾压降特性的影响[J]. 化工学报, 2012, 63(11): 3428-3433.

SUN Shuo, HU Haitao, DING Guoliang, ZHU Yu. Influence of metal foams on two-phase pressure drop of R410A flow boiling in circular tubes[J]. CIESC Journal, 2012, 63(11): 3428-3433.

参考文献 16

[1]	Fu Quanrong(付全荣),Zhang Yifen(张铱芬),Duan Zihua(段滋华),Li Yu(李煜).Applications of porous foam metals in chemical equipment[J].Chemical Engineering & Machinery(化工机械),2010,37(6):805-810
[2]	Kim D W.Convection and flow boiling in microgaps and porous foam coolers[D].Maryland:University of Maryland,2007
[3]	Zhu Yu(朱禹),Hu Haitao(胡海涛),Ding Guoliang(丁国良),Peng Hao(彭浩),Huang Xiangchao(黄翔超),Zhuang Dawei(庄大伟),Yu Jun(俞钧).Nucleate pool boiling heat transfer characteristics of refrigerant/ oil mixture on metal foam covers[J].CIESC Journal(化工学报),2011,62(2):329-335
[4]	Zhao C Y,Lu W,Tassou S A.Flow boiling heat transfer in horizontal metal-foam tubes[J].Journal of Heat Transfer-Transactions of the ASME,2009,131(12):121002-1
[5]	Chen Z Q,Cheng P,Zhao T S.An experimental study of two phase flow and boiling heat transfer in bi-dispersed porous channels[J].Int. Comm. Heat Mass Transfer,2000,27(3):293-302
[6]	Du Yanping(杜艳平),Qu Zhiguo(屈治国),Xu Huijin(徐会金),Zhao Changying(赵长颖),He Yaling(何雅玲),Tao Wenquan(陶文铨).Experimental investigation of boiling heat transfer in horizontal tube partially filled with metal-foam[J].Journal of Engineering Thermophysics(工程热物理学报),2010,31(10):1747-1751
[7]	Ji X B,Xu J L.Experimental study on the two-phase pressure drop in copper foams[J].Heat and Mass Transfer,2012,48(1):153-164
[8]	Topin F,Bonnet J P,Madani B,Tadrist L.Experimental analysis of multiphase flow in metallic foam:flow laws,heat transfer and convective boiling[J].Adv. Eng. Mater.,2006,8(9):890-899
[9]	Hu H T,Ding G L,Wei W J,Wang Z C,Wang K J.Measurement and correlation of frictional pressure drop of R410A/oil mixture flow boiling in a 7mm straight smooth tube[J].HVAC&R Research,2008,14(5):763-781
[10]	Wojtan L.Experimental and analytical investigation of void fraction and heat transfer during evaporation in horizontal tubes.Lausanne:Swiss Federal Institute of Technology,2004
[11]	Moffat R J.Describing the uncertainties in experimental results[J].Experimental Thermal and Fluid Science,1998,1(1):3-17
[12]	Hu H T,Ding G L,Wang K J.Measurement and correlation of frictional two-phase pressure drop of R410A/POE oil mixture flow boiling in a 7mm straight micro-fin tube[J].Applied Thermal Engineering,2008,28(11/12):1272-1283
[13]	Ergun S,Orning A A.Fluid flow through randomly packed columns and fluidized beds[J].Industrial and Engineering Chemistry Research,1949,41(6):1179-1184
[14]	Odile G,Thibaut V,Alain M,Bruno B.Experimental characterization of single and two-phase flow through nickel foams[J].Chem. Eng. Sci.,2009,64(19):4186-4195
[15]	Mancin S,Zilio C,Cavallini A,Rossetto L.Pressure drop during air flow in aluminum foams[J].International Journal of Heat and Mass Transfer,2010,53(15/16):3121-3130
[16]	Inayat A,Schwerdtfeger J,Freund H,Körner C,Singer R F,Schwieger W.Periodic open-cell foams:pressure drop measurements and modeling of an ideal tetrakaidecahedra packing[J].Chemical Engineering Science,2011,66(12):2758-2763

泡沫金属对圆管内R410A流动沸腾压降特性的影响

Influence of metal foams on two-phase pressure drop of R410A flow boiling in circular tubes

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献 16

相关文章 15

编辑推荐

Metrics

本文评价

[1]	江河, 袁俊飞, 王林, 邢谷雨. 均流腔结构对微细通道内相变流动特性影响的实验研究[J]. 化工学报, 2023, 74(S1): 235-244.
[2]	宋瑞涛, 王派, 王云鹏, 李敏霞, 党超镔, 陈振国, 童欢, 周佳琦. 二氧化碳直接蒸发冰场排管内流动沸腾换热数值模拟分析[J]. 化工学报, 2023, 74(S1): 96-103.
[3]	王玉兵, 李杰, 詹宏波, 朱光亚, 张大林. R134a在菱形离散肋微小通道内的流动沸腾换热实验研究[J]. 化工学报, 2023, 74(9): 3797-3806.
[4]	高金明, 郭玉娇, 鄂承林, 卢春喜. 一种封闭罩内顺流多旋臂气液分离器的分离特性研究[J]. 化工学报, 2023, 74(7): 2957-2966.
[5]	白剑钊, 郭子轩, 王德武, 刘燕, 王若瑾, 唐猛, 张少峰. 摇摆对气液并流模式立体旋流筛板压降的影响研究[J]. 化工学报, 2023, 74(2): 707-720.
[6]	禹言芳, 刘桓辰, 孟辉波, 刘励图, 李毓, 吴剑华. Lightnin静态混合器内气泡分散流体动力学特性实验研究[J]. 化工学报, 2022, 73(8): 3565-3575.
[7]	黄志豪, 李光熙, 唐桂华, 李小龙, 范元鸿. 单侧加热方形通道内超临界水传热研究[J]. 化工学报, 2022, 73(4): 1523-1533.
[8]	汪森林, 李照志, 邵应娟, 钟文琪. 超临界二氧化碳垂直管内传热恶化数值模拟研究[J]. 化工学报, 2022, 73(3): 1072-1082.
[9]	张苗, 杨洪海, 尹勇, 徐悦, 沈俊杰, 卢心诚, 施伟刚, 王军. 氧化石墨烯/水脉动热管的启动及传热特性[J]. 化工学报, 2022, 73(3): 1136-1146.
[10]	李广, 庄大伟, 谢丽懿, 丁国良, 郑立宇, 龙春仙, 江波. 含油R32管内流动沸腾换热特性测试及关联式开发[J]. 化工学报, 2022, 73(2): 612-621.
[11]	韩昌亮, 辛镜青, 于广滨, 刘俊秀, 许麒澳, 姚安卡, 尹鹏. 微通道内超临界氮气三维热流场实验与数值模拟[J]. 化工学报, 2022, 73(2): 653-662.
[12]	周云龙, 刘起超. 起伏振动倾斜上升管气液两相流摩擦阻力分析与计算[J]. 化工学报, 2022, 73(2): 643-652.
[13]	薛涵文, 聂峰, 赵延兴, 董学强, 郭浩, 沈俊, 公茂琼. 基于流型的R290水平管内流动沸腾压降实验研究[J]. 化工学报, 2022, 73(11): 4903-4916.
[14]	周培, 张秀平, 唐景春, 杨磊, 叶斌, 黄荣华. 过冷流动沸腾中气泡浮升直径的实验及理论研究[J]. 化工学报, 2022, 73(1): 194-203.
[15]	翁俊旗, 刘鑫磊, 余佳豪, 施尧, 叶光华, 屈进, 段学志, 李金兵, 周兴贵. 蜂窝状催化剂中空结构对固定床反应器压降的影响[J]. 化工学报, 2022, 73(1): 266-274.