气辅成型过程中可压缩空气流动数值模拟

doi:10.3969/j.issn.0438-1157.2013.03.017

化工学报 ›› 2013, Vol. 64 ›› Issue (3): 906-911.DOI: 10.3969/j.issn.0438-1157.2013.03.017

气辅成型过程中可压缩空气流动数值模拟

石宪章, 黄明, 赵振峰, 申长雨, 田中

郑州大学橡塑模具国家工程研究中心,河南郑州 450002

收稿日期:2012-05-24 修回日期:2012-09-19 出版日期:2013-03-05 发布日期:2013-03-05
通讯作者: 黄明
作者简介:石宪章(1967—),男,博士,副教授。

Numerical simulation of compressible gas flow in gas-assisted injection molding

SHI Xianzhang, HUANG Ming, ZHAO Zhenfeng, SHEN Changyu, TIAN Zhong

National Engineering Research Center for Advanced Polymer Processing Technology, Zhengzhou University, Zhengzhou 450002, Henan, China

Received:2012-05-24 Revised:2012-09-19 Online:2013-03-05 Published:2013-03-05

摘要/Abstract

摘要： 气辅成型技术能够有效地改善产品力学性能、提高产品的质量,因此在注射成型生产中应用广泛,与之相应的气辅成型CAE技术也得到了快速发展。当前的气辅成型CAE技术中假定空气为不可压缩流体,忽略了空气的可压缩性,因此研究气辅成型过程中可压缩空气的流动行为具有一定的实际意义。针对气辅成型过程中可压缩空气流动的复杂行为,基于假设将复杂的三维(3D)流动问题转化为二维(2D)。采用 CBS方法建立2D瞬态可压缩空气流动的有限元分析模型,求解算法采用预共轭梯度法,并用VC++完成了算法编制,实现了可压缩空气流动过程的数值模拟,其压力结果可作为充填流动分析的基础数据。

关键词: 气辅成型, 特征分列法, 数值模拟, 可压缩流动, 有限元法

Abstract: The use of gas-assisted technology is very popular in injection molding for its significant effect of improving mechanical properties and quality of products.Accordingly,the demand of gas-assisted CAE technology is also in the rising.In current CAE technology the compressibility of gas is neglected and gas or air pressure is usually imagined as a constant,such as a given value of the pressure at the inlet.But in fact,gas is strongly compressible and its pressure changes from a low value of zero to a high one before it is stabilized.It leaves unknown if these facts have any influence on the quality or mechanical properties of products.The objective of this paper is to study the complex behavior of compressible gas flow in the gas-assisted injection molding process.For simplification the real 3D flow was reduced to a 2D one based on certain assumption.A numerical simulation model of 2D transient compressible gas flow based on the characteristic-based-split method (CBS) was presented and a corresponding software with VC++ was established.Using this software a real simulation work was done.Its results could be taken as base data in further filling simulation.In addition,a pressure testing experiment was also done,and the comparison between simulation and experiment showed that the model presented in this paper was feasible.

Key words: gas-assisted injection molding, characteristic-based-split method, numerical simulation, compressible flow, finite element method

中图分类号:

TQ320
TP202

石宪章, 黄明, 赵振峰, 申长雨, 田中. 气辅成型过程中可压缩空气流动数值模拟[J]. 化工学报, 2013, 64(3): 906-911.

SHI Xianzhang, HUANG Ming, ZHAO Zhenfeng, SHEN Changyu, TIAN Zhong. Numerical simulation of compressible gas flow in gas-assisted injection molding[J]. CIESC Journal, 2013, 64(3): 906-911.

参考文献 12

[1]	Wang Lixia(王利霞),Shen Changyu(申长雨),Li Qian(李倩),Chen Jingbo(陈静波).Process and numerical simulation in filling stage of gas-assisted injection molding[J].Journal of Chemical Industry and Engineering(China)(化工学报),2003,54(2):176-181
[2]	Shen Changyu(申长雨).Injection Molding Simulation and Mold Optimization Design:Theory and Methods(注射成型模拟及模具优化设计理论与方法)[M].Beijing:Science Press,2009:128-197
[3]	Westborg H,Hassager O.Creeping motion of long bubbles and drops in capillary tubes[J].Journal of Colloid and Interface Science,1989,133(1):135-147
[4]	Liang Shuipo(梁水泊),Sun Nan(孙囡),Yang Wei(杨伟),Yang Bin(杨斌),Hu Sheng(胡升),Jing Lidan(景莉丹),Wei Jiali(危加丽),Yang Mingbo(杨鸣波).The MPI 3D simulation and experiment of the gas penetration behavior during gas-assisted injection molding[J].Polymer Materials Science and Engineering(高分子材料科学与工程),2009,25(8):118-121
[5]	Kong Qian(孔倩).Numerical simulation of gas-assisted injection molding gas filling process.Xi'an:Northwestern Polytechnical University,2007
[6]	Chen Wei(陈巍).The filling stage numerical simulation of gas assisted injection molding and robust optimization of processing .Shanghai:Shanghai Jiao Tong University,2011
[7]	Zienkiewicz O C.The Finite Element Method[M].Taylor R L,trans.5th ed.Singapore:Elsevier Pte. Itd.,2005:13-87
[8]	Codina R,Zienkiewicz O C.CBS versus GLS stabilization of the incompressible Navier-Stokes equations and the role of the time step as stabilization parameter[J].Communications in Numerical Methods in Engineering,2002,18(2):99-112
[9]	Nithiarasu P,Zienkiewicz O C.On stabilization of the CBS algorithm:internal and external time steps[J].International Journal for Numerical Methods in Engineering,2000,48(6):875-880
[10]	Nithiarasu P,Mathur J S,Weatherill N P,Morgan K.Three-dimensional incompressible flow calculations using the characteristic based split(CBS)scheme[J].Int.J.Numer.Meth.Fluids,2005,44(11):1207-1229
[11]	Massarotti N,Nithiarasu P,Zienkiewicz O C.Natural convection in porous medium-fluid interface problems—finite element analysis by using the CBS procedure[J].International Journal for Numerical Methods in Heat and Fluid Flow,2001(11):473- 490
[12]	Nithiarasu P,Codina Ramon,Zienkiewicz O C.The characteristic-based split(CBS)scheme—a unified approach to fluid dynamics[J].International Journal for Numerical Methods in Engineering,2006,66(10):1514-1546

[1]	宋嘉豪, 王文. 斯特林发动机与高温热管耦合运行特性研究[J]. 化工学报, 2023, 74(S1): 287-294.
[2]	张思雨, 殷勇高, 贾鹏琦, 叶威. 双U型地埋管群跨季节蓄热特性研究[J]. 化工学报, 2023, 74(S1): 295-301.
[3]	叶展羽, 山訸, 徐震原. 用于太阳能蒸发的折纸式蒸发器性能仿真[J]. 化工学报, 2023, 74(S1): 132-140.
[4]	张义飞, 刘舫辰, 张双星, 杜文静. 超临界二氧化碳用印刷电路板式换热器性能分析[J]. 化工学报, 2023, 74(S1): 183-190.
[5]	王志国, 薛孟, 董芋双, 张田震, 秦晓凯, 韩强. 基于裂隙粗糙性表征方法的地热岩体热流耦合数值模拟与分析[J]. 化工学报, 2023, 74(S1): 223-234.
[6]	何松, 刘乔迈, 谢广烁, 王斯民, 肖娟. 高浓度水煤浆管道气膜减阻两相流模拟及代理辅助优化[J]. 化工学报, 2023, 74(9): 3766-3774.
[7]	邢雷, 苗春雨, 蒋明虎, 赵立新, 李新亚. 井下微型气液旋流分离器优化设计与性能分析[J]. 化工学报, 2023, 74(8): 3394-3406.
[8]	程小松, 殷勇高, 车春文. 不同工质在溶液除湿真空再生系统中的性能对比[J]. 化工学报, 2023, 74(8): 3494-3501.
[9]	刘文竹, 云和明, 王宝雪, 胡明哲, 仲崇龙. 基于场协同和耗散的微通道拓扑优化研究[J]. 化工学报, 2023, 74(8): 3329-3341.
[10]	洪瑞, 袁宝强, 杜文静. 垂直上升管内超临界二氧化碳传热恶化机理分析[J]. 化工学报, 2023, 74(8): 3309-3319.
[11]	韩晨, 司徒友珉, 朱斌, 许建良, 郭晓镭, 刘海峰. 协同处理废液的多喷嘴粉煤气化炉内反应流动研究[J]. 化工学报, 2023, 74(8): 3266-3278.
[12]	黄可欣, 李彤, 李桉琦, 林梅. 加装旋转叶轮T型通道流场的模态分解[J]. 化工学报, 2023, 74(7): 2848-2857.
[13]	史方哲, 甘云华. 超薄热管启动特性和传热性能数值模拟[J]. 化工学报, 2023, 74(7): 2814-2823.
[14]	江锦波, 彭新, 许文烜, 门日秀, 刘畅, 彭旭东. 泵出型螺旋槽油气密封泄漏特性及参数影响研究[J]. 化工学报, 2023, 74(6): 2538-2554.
[15]	于源, 陈薇薇, 付俊杰, 刘家祥, 焦志伟. 几何相似涡流空气分级机环形区流场变化规律研究及预测[J]. 化工学报, 2023, 74(6): 2363-2373.

气辅成型过程中可压缩空气流动数值模拟

Numerical simulation of compressible gas flow in gas-assisted injection molding

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献 12

相关文章 15

编辑推荐

Metrics

本文评价