HFC134a水平二维与三维肋管外冷凝换热特性

doi:10.3969/j.issn.0438-1157.2014.04.010

化工学报 ›› 2014, Vol. 65 ›› Issue (4): 1221-1228.DOI: 10.3969/j.issn.0438-1157.2014.04.010

HFC134a水平二维与三维肋管外冷凝换热特性

马志先^1,2, 张吉礼¹, 孙德兴², 周浩平³

1 大连理工大学土木学院, 辽宁大连 110064;
2 哈尔滨工业大学市政环境工程学院, 黑龙江哈尔滨 150090;
3 江苏萃隆精密铜管股份有限公司, 江苏常熟 215562

收稿日期:2013-08-19 修回日期:2013-12-31 出版日期:2014-04-05 发布日期:2014-01-10
通讯作者: 张吉礼
作者简介:马志先（1982—），男，博士后。
基金资助:
国家自然科学基金项目（51078053）；“十二五”国家科技部支撑计划项目（2011BAJ03B12-3）：中国博士后科学基金项目：中央高校基本科研业务费项目（DUT12RC（3）81）。

Film condensation characteristics of HFC134a on enhanced horizontal tubes with two dimensional and three dimensional integral fins

MA Zhixian^1,2, ZHANG Jili¹, SUN Dexing², ZHOU Haoping³

1 School of Civil Engineering, Dalian University of Technology, Dalian 116024, Liaoning, China;
2 School of Municipal and Environment Engineering, Harbin Institute of Technology, Harbin 150090, Heilongjiang, China;
3 Jiangsu Cuilong Precision Copper Tube Corporation, Changshu 215562, Jiangsu, China

Received:2013-08-19 Revised:2013-12-31 Online:2014-04-05 Published:2014-01-10
Supported by:
supported by the National Natural Science Foundation of China(51078053),the National Science & Technology Pillar Program during the Twelfth Five-year Plan Period of China(2011BAJ03B12-3), China Postdoctoral Science Foundation Funded Project and the Fundamental Research Funds for the Central Universities(DUT12RC(3)81).

摘要/Abstract

摘要： 环保工质与高效冷凝管的应用对制冷行业实现节能减排意义重大，工质在强化管外膜状凝结换热特性是二者推广应用的关键。建立了水平管外膜状凝结换热试验系统，研究了HFC134a在4种二维肋管与2种三维肋管外的膜状凝结传热特性。试验管公称外径为19.05 mm、有效换热长度为1000 mm；试验中，通过改进的Wilson图解法获取试验管水侧对流传热系数。结果表明： HFC134a水平二维与三维肋管外冷凝传热系数分别达到同热通量下光管的11倍与19倍以上；HFC134a工质对应最佳二维肋管的肋密度在1069～1575fpm（肋每米）之间、肋高在0.7～1.5 mm之间，对应最优三维肋管（与本文试验肋型相似）肋密度低于2000fpm；既有二维肋管膜状凝结换热模型需要进一步完善，肋管结构优化过程中应遵循优先提升肋密度的原则。

关键词: 凝结, 传热, 膜, 模型, 强化管, HFC134a, 水平管

Abstract: Design of shell-tube condenser with finned tubes with two dimensional (2D) or three dimensional (3D) fins for HFC134a needs reliable models for the film condensation, which is usually based on reliable experimental data. A new test facility was established to investigate experimentally film condensation characteristics of HFC134a on six enhanced tubes (four kinds of 2D finned tubes and two kinds of 3D finned tubes) and the reliability of existing models and the effect of fin density and fin height on film condensation of HFC134a were discussed. Equivalent outside diameter and active length of test tubes are 19.05 and 1000 mm, respectively. In the experiment, water-side convection heat transfer coefficient for all test tubes is determined by the modified Wilson plot method. The results are as follows. Condensation heat transfer coefficient (CHTC) of HFC134a on single smooth tube is a little higher (5%—8%) than that predicted by the Nusselt model; CHTC of the best 2D (or 3D) finned tubes is 11.5 (or 19) times higher than that of single smooth tube under the same heat flux; the best fin density and fin height of 2D finned tubes are in the regions of 1069—1575 fins per meter (fpm) and 0.7—1.5 mm, respectively; the best fin density of the 3D finned tubes is less than 2000 fpm; the deviations between existing models and experimental results are not acceptable, due to their bad stability or poor accuracy. More work should be done to improve the models for film condensation of HFC134a on 2D finned tubes and develop models for that on 3D finned tubes in the future. The result can be used to guide the design of shell-tube condenser with HFC134a.

Key words: condensation, heat transfer, film, model, enhanced tube, HFC134a, horizontal tube

中图分类号:

TK124

马志先, 张吉礼, 孙德兴, 周浩平. HFC134a水平二维与三维肋管外冷凝换热特性[J]. 化工学报, 2014, 65(4): 1221-1228.

MA Zhixian, ZHANG Jili, SUN Dexing, ZHOU Haoping. Film condensation characteristics of HFC134a on enhanced horizontal tubes with two dimensional and three dimensional integral fins[J]. CIESC Journal, 2014, 65(4): 1221-1228.

参考文献

[1] Seara J F, Uhia F J, Diz R, Dopozo A. Condensation of R-134a on horizontal integral-fin titanium tubes[J]. Applied Thermal Engineering, 2010, 30: 295-301
[2] Cao Desheng(曹德胜), Shi Lin(史琳). Handbook for Refrigerant Application（制冷剂使用手册）[M]. Beijing: Metallurgical Industry Press, 2003
[3] Adamek T. Bestimmung der kondensation-grossen auf fe-ingewellten oberflachen zur auslegun aptimaler wandprofile[J]. Warme-und Stoffiibertragung, 1981, 15: 255-270
[4] Zhang Zhengguo(张正国), Lin Peisen(林培森), Wang Shiping(王世平). Development of petal-finned tube and research on its enhancement condensation heat transfer in longitudinal flow[J]. Petro-chemical Equipment(石油化工设备), 1996, 25(3): 3-6
[5] Kumar R, Varma H K, Mohanty B, Agrawal K N. Augmentation of heat transfer during filmwise condensation of steam and R-134a over single horizontal finned tubes[J]. Int. J. Heat Mass Transfer, 2002, 45: 201-211
[6] Ali H M, Briggs A. Enhanced condensation of ethylene glycol on single pin-fin tubes—effect of pin geometry [J]. Journal of Heat Transfer, 2012, 134: 1-7.
[7] Kumar R, Gupta A, Vishvakarma S. Condensation of R-134a vapour over single horizontal integral-fin tubes: effect of fin height[J]. Int. J. Refrig., 2005, 28: 428-435
[8] Belghazi M, Bontemps A, Marvillet C. Condensation heat transfer on enhanced surface tubes: experimental results and predictive theory[J]. Journal of Heat Transfer, 2002, 124: 754-761
[9] Honda H, Takata N, Takamatsu H, Kim J S, Usami K. Condensation of downward flowing HFC-134a in a staggered bundle of horizontal finned tubes: effect of fin geometry[J]. Int. J. Refrig., 2002, 25: 3-10
[10] Cheng W Y, Wang C C. Condensation of R134a on enhanced tubes[J]. ASHRAE Trans., 1994, 100(2): 809-817
[11] Rewert L E, Huber J B, Pate M B. The effect of R-134a inundation on enhanced tube geometries[J]. ASHRAE Trans., 1996, 102(2): 285-296
[12] Randall D L, Eckels S J. Effect of inundation upon condensation heat transfer performance of R-134a(Ⅱ): Results[J]. Int. J. HVAC&R Research, 2005, 11(4): 543-562
[13] Gstoehl D, Thome J R. Film condensation of R-134a on tube array with plain and enhanced surfaces(Ⅱ): Empirical prediction of inundation effects[J]. Journal of Heat Transfer, 2006, 128: 33-43
[14] Zhang D C, Ji W T, Tao W Q. Condensation heat transfer of HFC134a on horizontal low thermal conductivity tubes[J]. International Communications in Heat and Mass Transfer, 2007, 34: 917-923
[15] Yun R, Heo J, Kim Y. Film condensation heat transfer characteristics of R134a on horizontal stainless steel integral-fin tubes at low heat transfer rate[J]. Int. J. Refrig., 2009, 32: 865-873
[16] Beatty K O, Katz D L. Condensation of vapours on outside of finned tubes[J]. Chemical Engineering Progress, 1948, 44(1): 55-70
[17] Webb R L, Rudy T M, Keswan S T. Prediction of the condensation coefficient on horizontal integral-fin tube[J]. Journal of Heat Transfer, 1985, 107: 369-376
[18] Honda H, Nozu S. A prediction method for heat transfer during film condensation on horizontal low integral-fin tubes[J]. Journal of Heat Transfer, 1987, 109: 218-225
[19] Rose J W. An approximate equation for the vapour-side heat transfer coefficient for condensation on low-finned tubes[J]. Int. J. Heat Mass Transfer, 1994, 37: 865-875
[20] Briggs A, Rose J W. Effect of fin efficiency on a model for condensation heat tansfer on a horizontal integral-fin tube[J]. Int. J. Heat Mass Transfer, 1994, 37(1): 457-463
[21] Kumar R, Varma H K, Mohanty B. Prediction of heat transfer coefficient during condensation of water and R-134a on single horizontal integral-fin tubes[J]. Int. J. Refrig., 2002, 25: 111-126
[22] Ma Zhixian(马志先). Experimental investigation on condensation heat transfer and its enhancement of HFC245fa outside horizontal tube bundles[D]. Harbin: Harbin Institute of Technology, 2007: 58-60
[23] Ma Zhixian(马志先), Zhang Jili(张吉礼), Sun Dexing(孙德兴). Experimental study of condensation heat transfer coefficient of HFC245fa on bundles of horizontal smooth and enhanced tubes[J]. CIESC Journal (化工学报), 2010, 61(5): 1097-1106
[24] Ma Zhixian(马志先), Zhang Jili(张吉礼), Sun Dexing(孙德兴). Effect of inundation on film condensation of HFC245fa and HCFC123 on horizontal tubes[J]. J. Mech. Eng.(机械工程学报), 2012, 48(4): 129-135
[25] Zou Pinghua(邹平华). Design and investigation of head water tank for radiator test-bed[J]. Journal of Harbin University of Civil Engineering and Architecture(哈尔滨建筑工程学院学报), 1983(3): 70-74
[26] Zhao Xueduan(赵学端). Analysis of fluid dynamic of gravity water system for water flow-rate calibration device[J]. Journal of Shanghai Institute of Mechanical Engineering(上海机械学院学报)，1980 (3): 5-12
[27] Fujii T. Overlooked factors and unsolved problems in experimental research on condensation heat transfer[J]. Experimental Thermal and Fluid Science, 1992, 5: 652-663
[28] Seara J F, Uhia F J, Sieres J T, Gampo A. A general review of the Wilson plot method and its modifications to determine convection coefficients in heat exchange devices[J]. Applied Thermal Engineering, 2007, 27: 2745-2757
[29] Nusselt W. Die Oberflachenkondensation des wasserdampfes[J]. Z. Vereines Deutsch.Ing., 1916, 60: 541-546, 569-575
[30] Zhang Dingcai(张定才), Wang Kai(王凯), He Yaling(何雅玲), Tao Wenquan(陶文铨). Boiling heat transfer of R134a outside horizontal doubly-enhanced tubes[J]. Journal of Chemical Industry and Engineering（China）(化工学报), 2007, 58(11): 2710-2714
[31] Yang Shiming (杨世铭), Tao Wenquan (陶文铨). Heat Transfer（传热学）[M]. 4th ed. Beijing: Higher Education Press, 2006
[32] Wu Peiyi(吴沛宜). A criterial equation for condensation heat transfer of R12 and R113 on single horizontal finned tubes[J]. Journal of Xi’an Jiaotong University (西安交通大学学报)，1979, 1(3): 1-10
[33] Ma Zhixian(马志先), Zhang Jili(张吉礼), Sun Dexing(孙德兴). Theoretical development of laminar film condensation on single horizontal tube with one-dimensional and two-dimensional surfaces[J]. Journal of Harbin Institute of Technology (哈尔滨工业大学学报), 2011, 43: 80-93

HFC134a水平二维与三维肋管外冷凝换热特性

Film condensation characteristics of HFC134a on enhanced horizontal tubes with two dimensional and three dimensional integral fins

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	宋嘉豪, 王文. 斯特林发动机与高温热管耦合运行特性研究[J]. 化工学报, 2023, 74(S1): 287-294.
[2]	晁京伟, 许嘉兴, 李廷贤. 基于无管束蒸发换热强化策略的吸附热池的供热性能研究[J]. 化工学报, 2023, 74(S1): 302-310.
[3]	连梦雅, 谈莹莹, 王林, 陈枫, 曹艺飞. 地下水预热新风一体化热泵空调系统制热性能研究[J]. 化工学报, 2023, 74(S1): 311-319.
[4]	金正浩, 封立杰, 李舒宏. 氨水溶液交叉型再吸收式热泵的能量及分析[J]. 化工学报, 2023, 74(S1): 53-63.
[5]	程成, 段钟弟, 孙浩然, 胡海涛, 薛鸿祥. 表面微结构对析晶沉积特性影响的格子Boltzmann模拟[J]. 化工学报, 2023, 74(S1): 74-86.
[6]	苏伟, 马东旭, 金旭, 刘忠彦, 张小松. 表面润湿性对霜层传递特性影响可视化实验研究[J]. 化工学报, 2023, 74(S1): 122-131.
[7]	邵苛苛, 宋孟杰, 江正勇, 张旋, 张龙, 高润淼, 甄泽康. 水平方向上冰中受陷气泡形成和分布实验研究[J]. 化工学报, 2023, 74(S1): 161-164.
[8]	张双星, 刘舫辰, 张义飞, 杜文静. R-134a脉动热管相变蓄放热实验研究[J]. 化工学报, 2023, 74(S1): 165-171.
[9]	张义飞, 刘舫辰, 张双星, 杜文静. 超临界二氧化碳用印刷电路板式换热器性能分析[J]. 化工学报, 2023, 74(S1): 183-190.
[10]	陈爱强, 代艳奇, 刘悦, 刘斌, 吴翰铭. 基板温度对HFE7100液滴蒸发过程的影响研究[J]. 化工学报, 2023, 74(S1): 191-197.
[11]	刘明栖, 吴延鹏. 导光管直径和长度对传热影响的模拟分析[J]. 化工学报, 2023, 74(S1): 206-212.
[12]	王志国, 薛孟, 董芋双, 张田震, 秦晓凯, 韩强. 基于裂隙粗糙性表征方法的地热岩体热流耦合数值模拟与分析[J]. 化工学报, 2023, 74(S1): 223-234.
[13]	吴延鹏, 李晓宇, 钟乔洋. 静电纺丝纳米纤维双疏膜油性细颗粒物过滤性能实验分析[J]. 化工学报, 2023, 74(S1): 259-264.
[14]	李艺彤, 郭航, 陈浩, 叶芳. 催化剂非均匀分布的质子交换膜燃料电池操作条件研究[J]. 化工学报, 2023, 74(9): 3831-3840.
[15]	王玉兵, 李杰, 詹宏波, 朱光亚, 张大林. R134a在菱形离散肋微小通道内的流动沸腾换热实验研究[J]. 化工学报, 2023, 74(9): 3797-3806.