基于热管传热的盐水真空分离

doi:10.11949/j.issn.0438-1157.20150920

化工学报 ›› 2016, Vol. 67 ›› Issue (5): 1965-1972.DOI: 10.11949/j.issn.0438-1157.20150920

基于热管传热的盐水真空分离

高文忠, 李长松, 徐畅达, 刘婷

上海海事大学商船学院, 上海 201306

收稿日期:2015-06-12 修回日期:2016-01-13 出版日期:2016-05-05 发布日期:2016-05-05
通讯作者: 高文忠
基金资助:
国家自然科学基金项目(50976064);上海市自然科学基金项目(16ZR1414700)。

Heat pipe-based experimental study on water separation process in vacuum evaporator

GAO Wenzhong, LI Changsong, XU Changda, LIU Ting

Merchant Marine College, Shanghai Maritime University, Shanghai 201306, China

Received:2015-06-12 Revised:2016-01-13 Online:2016-05-05 Published:2016-05-05
Supported by:
supported by the National Natural Science Foundation of China (50976064) and the Natural Science Foundation of Shanghai (16ZR1414700).

摘要/Abstract

摘要：

将热管高效传热和高压喷雾技术应用于单级真空蒸发器,对含盐量3%的人造海水进行试验,结果表明:热管吸收40～80℃的低品位热源热量并以高热通量传递给闪蒸后的液滴,能保持甚至提高液滴蒸发过程的过热度,显著增大水分离率;冷热源温度取代初始过热度成为影响分离效果的主要因素,但要避免干壁现象;改变冷热源温度、初始过热度及流量能实现对分离率的调节。该方法对低品位热源在海水淡化工程中的有效利用、提升单位体积装置淡水产量和制取浓盐水均有重要参考价值。

关键词: 蒸发, 传热, 溶液, 分离

Abstract:

Based on the remarkable heat transfer performance of heat pipe (HP) and great specific surface area of small diameter droplets, HP and spray technologies are used in a novel single stage vacuum evaporator. And man-made seawater with 3% saltness is tested. Parameters affecting the performance such as temperature of cold source and heat source, spray temperature and spray flow are investigated. The result shows that the maximum heat flux of evaporator bland plate is 32 W·cm^-2. HPs absorb energy from low grade heat source between 40 to 80℃, and then transfer the energy to the droplets already flashed to keep or even increase the degree of superheat while evaporate. Thus, this method can significantly improve the water separation rate (quality of condensed water/quality of dilute solution ×100%). The initial superheat degree is replaced by temperature of cold source and heat source as the major factor on separating effect. The control of separation rate can be realized through adjusting the parameters. Therefore, this method has important implications for effective utilization of lower grade heat source, gaining brine and promoting the fresh water production unit volume and adaptability to variable load in desalination project.

Key words: evaporation, heat transfer, solution, separation

中图分类号:

TP273

高文忠, 李长松, 徐畅达, 刘婷. 基于热管传热的盐水真空分离[J]. 化工学报, 2016, 67(5): 1965-1972.

GAO Wenzhong, LI Changsong, XU Changda, LIU Ting. Heat pipe-based experimental study on water separation process in vacuum evaporator[J]. CIESC Journal, 2016, 67(5): 1965-1972.

参考文献 19

[1]	伍联营, 胡仰栋, 高从堦. 考虑水需求的水电联产海水淡化系统的优化设计 [J]. 化工学报, 2013, 64 (8): 2924-2929. DOI: 10.3969/j.issn.0438-1157.2013.08.032. WU L Y, HU Y D, GAO C J. Optimization design of cogeneration of power and fresh water by desalination considering fresh water demand [J]. CIESC Journal, 2013, 64(8): 2924-2929. DOI: 10.3969/j.issn.0438-1157.2013.08.032.
[2]	齐春华, 邢玉雷, 康权, 等. 30 t·d-1低温多效海水淡化装置中试试验 [J]. 化工学报, 2013, 64 (8): 3023-3030. DOI: 10.3969/j.issn.0438-1157.2013.08.046. QI C H, XING Y L, KANG Q, et al. Pilot test of a 30 t·d-1 desalination device with multi-effect and operated at low temperature by evaporating seawater [J]. CIESC Journal, 2013, 64 (8): 3023-3030. DOI: 10.3969/j.issn.0438-1157.2013.08.046.
[3]	沈胜强, 周士鹤, 牟兴森, 等. 大型低温多效蒸发海水淡化装置传热过程热力损失分析 [J]. 化工学报, 2014, 65 (9): 3366-3374. DOI: 10.3969/j.issn.0438-1157.2014.09.008. SHEN S Q, ZHOU S H, MU X S, et al. Analysis of thermodynamic losses of heat transfer process in large-scale LT-MED desalination plant [J]. CIESC Journal, 2014, 65(9): 3366-3374. DOI: 10.3969/j.issn.0438-1157.2014.09.008.
[4]	SRIMUANG W, AMATACHAYA P. A review of the applications of heat exchangers for heat recovery [J]. Renewable and Sustainable Energy Reviews, 2012, 16 (6): 4303-4315.
[5]	郭雪华. 热管式真空蒸发器的设计和试验研究 [D]. 大连: 大连理工大学, 2000. GUO X H. Design and experiments of heat-pipe vacuum evaporator [D]. Dalian: Dalian University of Technology, 2000.
[6]	杨茜. 热管式海水淡化装置开发与研究 [D]. 青岛: 青岛科技大学, 2014. YANG Q. Research and development of heat pipe desalination plant [D]. Qingdao: Qingdao University of Science & Technology, 2014.
[7]	Aquasonics International. Apparatus and method for thermal desalination based on pressurized formation and evaporation of droplets: US, 6699369 [P]. 2004-03-02.
[8]	IKEGAMIY, SASAKIH, GOUDAT, et al. Experimental study on a spray flash desalination (influence of the direction of injection [J]. Desalination, 2006, 194 (1/2/3): 81-89.
[9]	成怀刚, 高从堦. 喷雾蒸发海水淡化技术研究进展 [J]. 现代化工, 2008, 28 (6): 19-22+24. CHENG H G, GAO C J. Progress in spray evaporation desalination technology [J]. Modern Chemical Industry, 2008, 28 (6): 19-23.
[10]	RAHIMI M, ASGARY K, JESRI S. Thermal characteristics of a resurfaced condenser and evaporator closed two-phase thermo syphon [J]. International Communications in Heat and Mass Transfer, 2010, 37 (6): 703-710.
[11]	骆骞, 毕勤成, 韩彦宁, 等. 盐水液滴降压环境下蒸发过程 [J]. 化工学报, 2013, 64 (6): 2001-2006. DOI: 10.3969/j.issn.0438-1157.2013.06.014. LUO Q, BI Q C, HAN P N, et al. Evaporation process of brine droplet at reducing pressure [J]. CIESC Journal, 2013, 64 (6): 2001-2006. DOI: 10.3969/j.issn.0438-1157.2013.06.014.
[12]	GHERHARDT R, TOHN R, THOME. Experimental study on the onset of local dryout in an evaporating falling film on horizontal plain tubes [J]. Experimental Thermal and Fluid Science, 2007, 31: 483-493.
[13]	TARIF A A, BERTRAND H, JEAN V. Experimental results and modeling of boiling heat transfer coefficients in falling film evaporator usable for evaporator design [J]. Chemical Engineering and Processing: Process Intensification, 2009, 48: 961-68.
[14]	侯经纬, 成怀刚, 伍联营, 等. 基于低温蒸馏-喷雾蒸发集成工艺的海水淡化 [J]. 化学工程, 2010, (8): 94-97. HOU J W, CHENG H G, WU L Y, et al. Seawater desalination based on low temperature distillation and dray evaporation [J]. Chemical Engineering (China), 2010, (8): 94-97.
[15]	MUTHUNAYAGAM A E, RAMAMURTHI K, PADEN J R. Modelling and experiments on vaporization of saline water at low temperatures and reduced pressures [J]. Applied Thermal Engineering, 2005, 25 (5/6): 941-952.
[16]	邵福喜. 喷淋式闪蒸海水淡化的实验研究 [D]. 天津: 天津大学, 2007. SHAO F X. Experimental study on spray flash evaporation of seawater desalination [D]. Tianjin: Tianjin University, 2007.
[17]	PATRIK N, ALEXANDER ?, MILAN M. Mathematical model for heat transfer limitations of heat pipe [J]. Mathematical and Computer Modelling, 2013, 57 (1/2): 126-136.
[18]	KARTHIK K B, JAYATHI Y, MURTHY, et al. Evaporation analysis in sintered wick microstructures [J]. International Journal of Heat and Mass Transfer, 2013, 61: 729-741.
[19]	FERRANDI C, IORIZZO F, MAMELI M, et al. Lumped parameter model of sintered heat pipe: transient numerical analysis and validation [J]. Applied Thermal Engineering, 2013, 50: 1280-1290.

基于热管传热的盐水真空分离

Heat pipe-based experimental study on water separation process in vacuum evaporator

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献 19

相关文章 15

编辑推荐

Metrics

本文评价

[1]	吴馨, 龚建英, 靳龙, 王宇涛, 黄睿宁. 超声波激励下铝板表面液滴群输运特性的研究[J]. 化工学报, 2023, 74(S1): 104-112.
[2]	叶展羽, 山訸, 徐震原. 用于太阳能蒸发的折纸式蒸发器性能仿真[J]. 化工学报, 2023, 74(S1): 132-140.
[3]	张双星, 刘舫辰, 张义飞, 杜文静. R-134a脉动热管相变蓄放热实验研究[J]. 化工学报, 2023, 74(S1): 165-171.
[4]	毕丽森, 刘斌, 胡恒祥, 曾涛, 李卓睿, 宋健飞, 吴翰铭. 粗糙界面上纳米液滴蒸发模式的分子动力学研究[J]. 化工学报, 2023, 74(S1): 172-178.
[5]	张义飞, 刘舫辰, 张双星, 杜文静. 超临界二氧化碳用印刷电路板式换热器性能分析[J]. 化工学报, 2023, 74(S1): 183-190.
[6]	陈爱强, 代艳奇, 刘悦, 刘斌, 吴翰铭. 基板温度对HFE7100液滴蒸发过程的影响研究[J]. 化工学报, 2023, 74(S1): 191-197.
[7]	刘明栖, 吴延鹏. 导光管直径和长度对传热影响的模拟分析[J]. 化工学报, 2023, 74(S1): 206-212.
[8]	王志国, 薛孟, 董芋双, 张田震, 秦晓凯, 韩强. 基于裂隙粗糙性表征方法的地热岩体热流耦合数值模拟与分析[J]. 化工学报, 2023, 74(S1): 223-234.
[9]	晁京伟, 许嘉兴, 李廷贤. 基于无管束蒸发换热强化策略的吸附热池的供热性能研究[J]. 化工学报, 2023, 74(S1): 302-310.
[10]	常明慧, 王林, 苑佳佳, 曹艺飞. 盐溶液蓄能型热泵循环特性研究[J]. 化工学报, 2023, 74(S1): 329-337.
[11]	金正浩, 封立杰, 李舒宏. 氨水溶液交叉型再吸收式热泵的能量及分析[J]. 化工学报, 2023, 74(S1): 53-63.
[12]	程成, 段钟弟, 孙浩然, 胡海涛, 薛鸿祥. 表面微结构对析晶沉积特性影响的格子Boltzmann模拟[J]. 化工学报, 2023, 74(S1): 74-86.
[13]	张化福, 童莉葛, 张振涛, 杨俊玲, 王立, 张俊浩. 机械蒸汽压缩蒸发技术研究现状与发展趋势[J]. 化工学报, 2023, 74(S1): 8-24.
[14]	李艺彤, 郭航, 陈浩, 叶芳. 催化剂非均匀分布的质子交换膜燃料电池操作条件研究[J]. 化工学报, 2023, 74(9): 3831-3840.
[15]	王玉兵, 李杰, 詹宏波, 朱光亚, 张大林. R134a在菱形离散肋微小通道内的流动沸腾换热实验研究[J]. 化工学报, 2023, 74(9): 3797-3806.