水辅助注塑中高压水穿透过程的数值模拟

doi:10.3969/j.issn.0438-1157.2013.04.006

化工学报 ›› 2013, Vol. 64 ›› Issue (4): 1170-1175.DOI: 10.3969/j.issn.0438-1157.2013.04.006

水辅助注塑中高压水穿透过程的数值模拟

汪志泳, 黄汉雄, 汪斌

华南理工大学塑料橡胶装备及智能化中心,广东广州 510640

收稿日期:2012-07-24 修回日期:2012-11-15 出版日期:2013-04-05 发布日期:2013-04-05
通讯作者: 黄汉雄
作者简介:汪志泳(1987—),男,硕士研究生。
基金资助:
国家自然科学基金项目(20874031)。

Numerical simulation of water penetration in water-assisted injection molding

WANG Zhiyong, HUANG Hanxiong, WANG Bin

Center for Polymer Processing Equipment and Intellectualization, South China University of Technology, Guangzhou 510640, Guangdong, China

Received:2012-07-24 Revised:2012-11-15 Online:2013-04-05 Published:2013-04-05
Supported by:
supported by the National Natural Science Foundation of China (20874031).

摘要/Abstract

摘要： 对水辅助注塑(WAIM)中高压水的穿透过程进行有限元模拟,研究熔体的充模行为,并分析其拉伸场和剪切场。结果显示,高压水推动熔体充模的过程可分为填充初期、快速填充期和填充末期3个阶段;较明显的拉伸应变速率仅出现在高压水前沿和熔体前沿区域;高压水前沿区域存在分布较宽且较为强烈的剪切速率,而高压水对已穿透区域的熔体几乎没有剪切作用。此外,模拟所得WAIM制品的穿透长度和掏空率与实验结果较吻合。

关键词: 聚合物, 水辅助注塑, 数值模拟, 穿透行为, 流场

Abstract: The process of high-pressure water penetration in water-assisted injection molding (WAIM) was simulated based on the volume of fluid method, and the filling behavior of polymer melt as well as the elongation and shear fields were studied and analyzed.The simulated results showed that the process of melt filling propelled by high-pressure water was divided into three stages, namely, initial filling, fast filling, and terminal filling stages.Remarkable elongational rate was only present in the regions near both water and melt fronts.Widely-distributed and high shear rate was present in the region near the water front, whereas water had little shear effect on the melt in the water-penetrated zone.The simulated penetration length and hollow rate of the WAIM part matched well with the experimentally determined ones.

Key words: polymer, water-assisted injection molding, numerical simulation, penetration behavior, flow field

中图分类号:

TQ320.66

汪志泳, 黄汉雄, 汪斌. 水辅助注塑中高压水穿透过程的数值模拟[J]. 化工学报, 2013, 64(4): 1170-1175.

WANG Zhiyong, HUANG Hanxiong, WANG Bin. Numerical simulation of water penetration in water-assisted injection molding[J]. CIESC Journal, 2013, 64(4): 1170-1175.

参考文献 17

[1]	Knights M.Water injection molding makes hollow parts faster, lighter[J].Plastics Technology, 2002, 48(4):42-47,62-63
[2]	Huang H X, Zhou R H, Zhou W W.Morphology development of polypropylene/polyamide 6 blend molded by water-assisted injection molding//Proceedings of ANTEC[C].Brookfield, USA:Society of Plastics Engineers, 2009:2895-2899
[3]	Huang H X, Zhou R H.Preliminary investigation on morphology in water-assisted injection molded polymer blends[J].Polymer Testing, 2010, 29(2):235-244
[4]	Lin K Y, Liu S J.Morphology of fluid assisted injection molded polycarbonate/polyethylene blends[J].Macromolecular Materials and Engineering, 2010, 295(4):342-350
[5]	Wang B, Huang H X, Lu H Y.Crystal morphology of water-assisted injection molded high-density polyethylene with two different molecular weights[J].Journal of Macromolecular Science, Part B:Physics, 2011, 50(8):1615-1624
[6]	Wang B, Huang H X.Formation mechanism of crystal morphologies in LLDPE/HDPE blends investigated via water-assisted and conventional injection molding[J].Polymer Engineering and Science, 2012, 52(1):117-124
[7]	Huang H X, Wang B, Zhou W W.Polymorphism in polyamide 6 and polyamide 6/clay nanocomposites molded via water-assisted injection molding[J].Composites Part B:Engineering, 2012, 43(3):972-977
[8]	Liu X H, Zheng G Q, Jia Z H, Li S W, Liu C G, Zhang Y, Shao C G, Dai K, Liu B C, Zhang Q X, Wang S J, Liu C T, Chen J B, Peng X F, Shen C Y.The hierarchical structure of water-assisted injection molded high density polyethylene:small angle X-ray scattering study[J].Journal of Applied Polymer Science, 2012, 125(3):2297-2303
[9]	Liu Xuhui(刘旭辉), Huang Hanxiong(黄汉雄).Visualization analysis of water penetration behavior in water-assisted injection molding[J].China Plastics(中国塑料), 2009, 23(3):58-61
[10]	Liu Xuhui(刘旭辉), Huang Hanxiong(黄汉雄).Melt flow patterns in water-assisted melt filling[J].CIESC Journal(化工学报), 2010, 61(10):2523-2528
[11]	Liu Xuhui(刘旭辉), Huang Hanxiong(黄汉雄).Effects of processing conditions on melt flow of water assisted melt filling[J].CIESC Journal (化工学报), 2011, 62(2):520-524
[12]	Chang R Y, Huang C T, Yang W H, Tsai M H, Lu K I, Liu S J.The investigation of flow behavior of polymeric melts in the water assisted injection molding//Proceedings of ANTEC[C].Brookfield, USA:Society of Plastics Engineers, 2004:566-569
[13]	Silva L, Lanrivain R, Zerguine W, Rodriguez-Villa A, Coupez T.Two-phase model of liquid-liquid interactions with interface capturing:application to water assisted injection molding//NUMIFORM 2007:Materials Processing and Design, Modeling, Simulation and Applications[C].New York:American Institute of Physics, 2007:361-366
[14]	Polynkin A, Bai L, Pittman J F T, Sienz J, Mulvaney-Johnson L, Brown E, Dawson A, Coates P, Brookshaw B, Vinning K, Butler J.Water assisted injection moulding:development of insights and predictive capabilities through experiments on instrumented process in parallel with computer simulations[J].Plastics, Rubber and Composites,2008, 37(2/3/4):131-141
[15]	Zhang Zengmeng(张增猛), Zhou Hua(周华), Gao Yuan’an(高院安), Yang Huayong(杨华勇).Simulation and analysis on cavity filling process in water-assisted injection molding[J].Journal of Mechanical Engineering(机械工程学报), 2010, 46(8):140-146
[16]	Wu Qiye(吴其晔), Wu Jing’an(巫静安).Polymer Rheology(高分子材料流变学)[M].Beijing:Higher Education Press, 2002:45-49
[17]	Huang H X, Deng Z W.Effects and optimization of processing parameters in water-assisted injection molding[J].Journal of Applied Polymer Science, 2008, 108(1):228-235

水辅助注塑中高压水穿透过程的数值模拟

Numerical simulation of water penetration in water-assisted injection molding

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献 17

相关文章 15

编辑推荐

Metrics

本文评价

[1]	叶展羽, 山訸, 徐震原. 用于太阳能蒸发的折纸式蒸发器性能仿真[J]. 化工学报, 2023, 74(S1): 132-140.
[2]	张义飞, 刘舫辰, 张双星, 杜文静. 超临界二氧化碳用印刷电路板式换热器性能分析[J]. 化工学报, 2023, 74(S1): 183-190.
[3]	王志国, 薛孟, 董芋双, 张田震, 秦晓凯, 韩强. 基于裂隙粗糙性表征方法的地热岩体热流耦合数值模拟与分析[J]. 化工学报, 2023, 74(S1): 223-234.
[4]	宋嘉豪, 王文. 斯特林发动机与高温热管耦合运行特性研究[J]. 化工学报, 2023, 74(S1): 287-294.
[5]	张思雨, 殷勇高, 贾鹏琦, 叶威. 双U型地埋管群跨季节蓄热特性研究[J]. 化工学报, 2023, 74(S1): 295-301.
[6]	何松, 刘乔迈, 谢广烁, 王斯民, 肖娟. 高浓度水煤浆管道气膜减阻两相流模拟及代理辅助优化[J]. 化工学报, 2023, 74(9): 3766-3774.
[7]	邢雷, 苗春雨, 蒋明虎, 赵立新, 李新亚. 井下微型气液旋流分离器优化设计与性能分析[J]. 化工学报, 2023, 74(8): 3394-3406.
[8]	程小松, 殷勇高, 车春文. 不同工质在溶液除湿真空再生系统中的性能对比[J]. 化工学报, 2023, 74(8): 3494-3501.
[9]	刘文竹, 云和明, 王宝雪, 胡明哲, 仲崇龙. 基于场协同和耗散的微通道拓扑优化研究[J]. 化工学报, 2023, 74(8): 3329-3341.
[10]	洪瑞, 袁宝强, 杜文静. 垂直上升管内超临界二氧化碳传热恶化机理分析[J]. 化工学报, 2023, 74(8): 3309-3319.
[11]	韩晨, 司徒友珉, 朱斌, 许建良, 郭晓镭, 刘海峰. 协同处理废液的多喷嘴粉煤气化炉内反应流动研究[J]. 化工学报, 2023, 74(8): 3266-3278.
[12]	王杰, 丘晓琳, 赵烨, 刘鑫洋, 韩忠强, 许雍, 蒋文瀚. 聚电解质静电沉积改性PHBV抗氧化膜的制备与性能研究[J]. 化工学报, 2023, 74(7): 3068-3078.
[13]	刘杰, 吴立盛, 李锦锦, 罗正鸿, 周寅宁. 含乙烯基胺酯键聚醚类可逆交联聚合物的制备及性能研究[J]. 化工学报, 2023, 74(7): 3051-3057.
[14]	黄可欣, 李彤, 李桉琦, 林梅. 加装旋转叶轮T型通道流场的模态分解[J]. 化工学报, 2023, 74(7): 2848-2857.
[15]	史方哲, 甘云华. 超薄热管启动特性和传热性能数值模拟[J]. 化工学报, 2023, 74(7): 2814-2823.