辐射吊顶表面冷凝液滴脱落尺寸分析

doi:10.11949/j.issn.0438-1157.20160292

化工学报 ›› 2016, Vol. 67 ›› Issue (9): 3552-3558.DOI: 10.11949/j.issn.0438-1157.20160292

辐射吊顶表面冷凝液滴脱落尺寸分析

唐海达, 张涛, 刘晓华, 江亿

清华大学建筑学院, 北京 100084

收稿日期:2016-03-11 修回日期:2016-06-07 出版日期:2016-09-05 发布日期:2016-09-05
通讯作者: 张涛
基金资助:
国家科技支撑计划项目（2014BAJ02B01）；广东省科技计划项目（2013A090100016）。

Size of departing condensate droplets from radiant cooling ceiling

TANG Haida, ZHANG Tao, LIU Xiaohua, JIANG Yi

School of Architecture, Tsinghua University, Beijing 100084, China

Received:2016-03-11 Revised:2016-06-07 Online:2016-09-05 Published:2016-09-05
Supported by:
supported by the National Key Technology Support Program (2014BAJ02B01) and the Science and Technology Planning Project of Guangdong Province (2013A090100016).

摘要/Abstract

摘要：

通过对超疏水纯铜样品和4种经过不同表面改性处理的铝合金样品的冷凝实验，系统地研究了表面特性不同的辐射吊顶表面冷凝液滴的脱落尺寸。结果表明，超疏水表面合并诱导脱落的液滴半径不足300 μm，而且尺寸相近的微小液滴（半径之比在1.0～1.5）合并后易于发生液滴脱落。根据能量守恒原理对液滴合并过程进行了理论分析，结果表明随着合并前两液滴半径之比的增大，液滴合并脱落的阻力，黏附功和黏性耗散相比于合并后释放的表面能均变得显著，从而导致液滴合并脱落的概率减小。常规辐射吊顶表面上重力诱导脱落的液滴半径随机分布在2.0～6.0 mm，但在表面的后退角和前进角所确定的上、下限范围内。因此，超疏水处理后的辐射吊顶大幅减小了冷凝液滴的脱落尺寸，可显著降低其表面结露风险。

关键词: 凝结, 超疏水表面, 接触角, 热力学, 数值模拟

Abstract:

The size of condensate droplets departing from horizontal superhydrophobic copper surfaces and conventional aluminum alloy surfaces was studied experimentally and theoretically. During the whole condensation experiment, the dew formation and departure underneath the sample surfaces were imaged by CCD. It was found that the radius of the condensate droplets of the coalescence-induced jumping condensate departed from the superhydrophobic surface was below 300 μm. The coalesced droplets merged by micro-droplets with a radius ratio ranging from 1.0 to 1.5 were subject to self-removal from the superhydrophobic surface. This was because the driving force of the released surface energy after droplet coalescence became dominant compared to the resistance of the work of adhesion and viscous dissipation with the decrease of the radius ratio. In addition, the radii of the gravity-induced falling droplet from conventional aluminum alloy surfaces were ranged from 2.0 mm to 6.0 mm, and limited by the advancing and receding contact angles. Therefore, these results revealed that the superhydrophobic surface can significantly decrease the size of droplets departing from radiant ceiling panels and reduce condensation risks of radiant cooling ceiling systems.

Key words: condensation, superhydrophobic surface, contact angle, thermodynamics, numerical simulation

中图分类号:

TK124

唐海达, 张涛, 刘晓华, 江亿. 辐射吊顶表面冷凝液滴脱落尺寸分析[J]. 化工学报, 2016, 67(9): 3552-3558.

TANG Haida, ZHANG Tao, LIU Xiaohua, JIANG Yi. Size of departing condensate droplets from radiant cooling ceiling[J]. CIESC Journal, 2016, 67(9): 3552-3558.

参考文献 21

[1]	清华大学建筑节能研究中心. 中国建筑节能年度发展研究报告2011[M]. 北京:中国建筑工业出版社, 2011:2-6. Building Energy Research Center of Tsinghua University. 2011 Annual Report on China Building Energy Efficiency[M]. Beijing:China Architecture & Building Press, 2011:2-6.
[2]	PEREZ-LOMBARD L, ORTIZ J, POUT C. A review on buildings energy consumption information[J]. Energy Build., 2008, 40(3):394-398.
[3]	MEMON R A, CHIRARATTANANON S, VANGTOOK P. Thermal comfort assessment and application of radiant cooling:a case study[J]. Building and Environment, 2008, 43(7):1185-1196.
[4]	SUI X, ZHANG X. Effects of radiant terminal and air supply terminal devices on energy consumption of cooling load sharing rate in residential buildings[J]. Energy Build., 2012, 49:499-508.
[5]	CHIANG W H, WANG C Y, HUANG J S. Evaluation of cooling ceiling and mechanical ventilation systems on thermal comfort using CFD study in an office for subtropical region[J]. Building and Environment, 2012, 48:113-127.
[6]	TIAN Z, LOVE J A. Energy performance optimization of radiant slab cooling using building simulation and field measurements[J]. Energy Build., 2009, 41(3):320-330.
[7]	RHEE K N, KIM K W. A 50 year review of basic and applied research in radiant heating and cooling systems for the built environment[J]. Building and Environment, 2015, 91:166-190.
[8]	YIN Y L, WANG R Z, ZHAI X Q, et al. Experimental investigation on the heat transfer performance and water condensation phenomenon of radiant cooling panels[J]. Building and Environment, 2014, 71:15-23.
[9]	TANG H, LIU X H. Experimental study of dew formation on metal radiant panels[J]. Energy Build., 2014, 85:515-523.
[10]	DIMITRAKOPOULOS P, HIGDON J J L. On the gravitational displacement of three-dimensional fluid droplets from inclined solid surfaces[J]. J. Fluid Mech., 1999, 395:181-209.
[11]	BOREYKO J B, CHEN C H. Self-propelled dropwise condensate on superhydrophobic surfaces[J]. Phys. Rev. Lett., 2009, 103(18):184501.
[12]	FENG J, QIN Z, YAO S. Factors affecting the spontaneous motion of condensate drops on superhydrophobic copper surfaces[J]. Langmuir, 2012, 28(14):6067-6075.
[13]	LV C, HAO P, YAO Z, et al. Condensation and jumping relay of droplets on lotus leaf[J]. Appl. Phys. Lett., 2013, 103(2):021601.
[14]	王四芳, 兰忠, 彭本利, 等. 超疏水表面液滴合并诱导弹跳现象分析[J]. 化工学报, 2012, 63(S1):17-22. WANG S F, LAN Z, PENG B L, et al. Characteristics of droplet coalescence and self-propelling on superhydrophobic surface[J]. CIESC Journal, 2012, 63(S1):17-22.
[15]	王四芳, 兰忠, 王爱丽, 等. 超疏水表面蒸汽及含不凝气蒸汽滴状冷凝传热实验分析[J]. 化工学报, 2010, 61(3):607-611. WANG S F, LAN Z, WANG A L, et al. Dropwise condensation of steam and steam-air mixture on super-hydrophobic surfaces[J]. CIESC Journal, 2010, 61(3):607-611.
[16]	RYKACZEWSKI K, PAXSON A T, ANAND S, et al. Multimode multidrop serial coalescence effects during condensation on hierarchical superhydrophobic surfaces[J]. Langmuir, 2013, 29(3):881-891.
[17]	CHEN X, KONG L, DONG D, et al. Fabrication of functionalized copper compound hierarchical structure with bionic superhydrophobic properties[J]. J. Phys. Chem. C, 2009, 113(14):5396-5401.
[18]	GAO L, MCCARTHY T J. Wetting 101°[J]. Langmuir, 2009, 25(24):14105-14115.
[19]	WANG F C, YANG F, ZHAO Y P. Size effect on the coalescence-induced self-propelled droplet[J]. Appl. Phys. Lett., 2011, 98(5):053112.
[20]	FUCHIKAMI N, ISHIOKA S, KIYONO K. Simulation of a dripping faucet[J]. J. Phys. Soc. Japan, 1999, 68(4):1185-1196.
[21]	PITTS E. The stability of pendent liquid drops(2):Axial symmetry[J]. J. Fluid Mech., 1974, 63(3):487-508.

辐射吊顶表面冷凝液滴脱落尺寸分析

Size of departing condensate droplets from radiant cooling ceiling

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献 21

相关文章 15

编辑推荐

Metrics

本文评价

[1]	苏伟, 马东旭, 金旭, 刘忠彦, 张小松. 表面润湿性对霜层传递特性影响可视化实验研究[J]. 化工学报, 2023, 74(S1): 122-131.
[2]	叶展羽, 山訸, 徐震原. 用于太阳能蒸发的折纸式蒸发器性能仿真[J]. 化工学报, 2023, 74(S1): 132-140.
[3]	张义飞, 刘舫辰, 张双星, 杜文静. 超临界二氧化碳用印刷电路板式换热器性能分析[J]. 化工学报, 2023, 74(S1): 183-190.
[4]	王志国, 薛孟, 董芋双, 张田震, 秦晓凯, 韩强. 基于裂隙粗糙性表征方法的地热岩体热流耦合数值模拟与分析[J]. 化工学报, 2023, 74(S1): 223-234.
[5]	杨欣, 王文, 徐凯, 马凡华. 高压氢气加注过程中温度特征仿真分析[J]. 化工学报, 2023, 74(S1): 280-286.
[6]	宋嘉豪, 王文. 斯特林发动机与高温热管耦合运行特性研究[J]. 化工学报, 2023, 74(S1): 287-294.
[7]	张思雨, 殷勇高, 贾鹏琦, 叶威. 双U型地埋管群跨季节蓄热特性研究[J]. 化工学报, 2023, 74(S1): 295-301.
[8]	常明慧, 王林, 苑佳佳, 曹艺飞. 盐溶液蓄能型热泵循环特性研究[J]. 化工学报, 2023, 74(S1): 329-337.
[9]	张化福, 童莉葛, 张振涛, 杨俊玲, 王立, 张俊浩. 机械蒸汽压缩蒸发技术研究现状与发展趋势[J]. 化工学报, 2023, 74(S1): 8-24.
[10]	何松, 刘乔迈, 谢广烁, 王斯民, 肖娟. 高浓度水煤浆管道气膜减阻两相流模拟及代理辅助优化[J]. 化工学报, 2023, 74(9): 3766-3774.
[11]	胡建波, 刘洪超, 胡齐, 黄美英, 宋先雨, 赵双良. 有机笼跨细胞膜易位行为的分子动力学模拟研究[J]. 化工学报, 2023, 74(9): 3756-3765.
[12]	韩晨, 司徒友珉, 朱斌, 许建良, 郭晓镭, 刘海峰. 协同处理废液的多喷嘴粉煤气化炉内反应流动研究[J]. 化工学报, 2023, 74(8): 3266-3278.
[13]	张曼铮, 肖猛, 闫沛伟, 苗政, 徐进良, 纪献兵. 危废焚烧处理耦合有机朗肯循环系统工质筛选与热力学优化[J]. 化工学报, 2023, 74(8): 3502-3512.
[14]	程小松, 殷勇高, 车春文. 不同工质在溶液除湿真空再生系统中的性能对比[J]. 化工学报, 2023, 74(8): 3494-3501.
[15]	刘文竹, 云和明, 王宝雪, 胡明哲, 仲崇龙. 基于场协同和耗散的微通道拓扑优化研究[J]. 化工学报, 2023, 74(8): 3329-3341.