化工学报 ›› 2015, Vol. 66 ›› Issue (7): 2521-2527.DOI: 10.11949/j.issn.0438-1157.20150032

• 催化、动力学与反应器 • 上一篇    下一篇

低温预制钛系催化剂合成cis-1,4-聚异戊二烯

汪昭玮1,2, 于俊伟3, 李兴2, 刘晓暄1   

  1. 1 广东工业大学材料与能源学院高分子材料与工程系, 广东 广州 510006;
    2 中国广州分析测试中心, 广东省分析测试技术公共实验室, 广东 广州 510070;
    3 茂名鲁华化工有限公司, 广东 茂名 525000
  • 收稿日期:2015-01-09 修回日期:2015-04-27 出版日期:2015-07-05 发布日期:2015-07-05
  • 通讯作者: 刘晓暄
  • 基金资助:

    省部产学研合作重大专项(入库)鲁华分项(2012A090300006)。

Synthesis of cis-1,4-polyisoprene with low-temperature prepared Ti-Al catalysts

WANG Zhaowei1,2, YU Junwei3, LI Xing2, LIU Xiaoxuan1   

  1. 1 Department of Polymeric Materials and Engineering, School of Materials and Energy, Guangdong University of Technology, Guangzhou 510006, Guangdong, China;
    2 Guangdong Provincial Public Laboratory of Analysis and Testing Technology, China National Analytical Center, Guangzhou 510070, Guangdong, China;
    3 Maoming Luhua Chemical Engineering Ltd. Co., Maoming 525000, Guangdong, China
  • Received:2015-01-09 Revised:2015-04-27 Online:2015-07-05 Published:2015-07-05

摘要:

采用Ziegler-Natta配位聚合制备了高顺式聚异戊二烯,主要考察了非均相催化体系四氯化钛-三异丁基铝二组分催化剂的预制方法以及催化剂预制条件对异戊二烯体系聚合规律的影响。讨论了催化剂配比、预制催化剂温度和陈化温度对催化剂活性及聚合物的凝胶含量、特征黏度、微观结构含量等方面的影响。同时讨论了催化剂用量、聚合温度和聚合时间对聚合活性及聚合物的凝胶含量、特征黏度、微观含量等方面的影响。研究结果表明,合成高cis-1,4-聚异戊二烯的最佳实验条件为:Al/Ti摩尔比1.0,催化剂预制温度-40℃,陈化2 h,Ti/Ip摩尔比6×10-3,聚合温度50℃,聚合时间5 h。所得聚合物最高转化率为87.1%,cis-1,4结构含量为91.76%。

关键词: 催化剂, 配位聚合, cis-1,4-聚异戊二烯, 低温, 多相反应, 活性

Abstract:

The high cis-1,4-polyisoprene is prepared by Ziegler-Natta coordination polymerization. The effect of preparation method and condition of heterogeneous TiCl4-Al(i-Bu)3 two component catalyst on isoprene polymerization are investigated. The influence of several parameters on the catalytic activity, the gel content, intrinsic viscosity, microstructure and cis-1,4-content of the polyisoprene is examined in detail, including mole ratio of catalyst component, prefabricate temperature and aging time as well as catalyst dosage, polymerization temperature and time. The results show that the optimum conditions of catalyst preparation are as follows: the molar ratio of Al/Ti is 1.0, the temperature of prefabricate is at -40℃, the aging time is 2 h at room temperature, molar ratio of Ti/Ip(catalyst content)is 6×10-3, the polymerization for 5 h at 50℃. Under these condition, the monomer conversion is 87.1% in the polymerization, the microstructure cis-1,4 content in obtained polymer is up to 91.76%.

Key words: catalyst, Ziegler-Natta polymerization, cis-1,4-polyisoprene, low-temperature, multiphase reaction, reactivity

中图分类号: