化工学报 ›› 2015, Vol. 66 ›› Issue (7): 2464-2473.DOI: 10.11949/j.issn.0438-1157.20150204

• 流体力学与传递现象 • 上一篇    下一篇

基于数值模拟的自泵送机械密封正交试验

顾东升, 孙见君, 马晨波, 陆建花   

  1. 南京林业大学机械电子工程学院, 江苏 南京 210037
  • 收稿日期:2015-02-09 修回日期:2015-03-16 出版日期:2015-07-05 发布日期:2015-07-05
  • 通讯作者: 孙见君
  • 基金资助:

    国家级大学生实践创新训练计划资助项目(201410298051Z)。

Orthogonal test of self-pumping mechanical seals based on numerical simulation

GU Dongsheng, SUN Jianjun, MA Chenbo, LU Jianhua   

  1. College of Mechanical and Electrical Engineering, Nanjing Forestry University, Nanjing 210037, Jiangsu, China
  • Received:2015-02-09 Revised:2015-03-16 Online:2015-07-05 Published:2015-07-05
  • Supported by:

    supported by the National Practice Innovation Training Program Funded Projects for the College Students (201410298051Z).

摘要:

提出了一种进液槽设置于静环、动压槽分布于动环的自泵送流体动压型机械密封;运用正交试验法设计了自泵送机械密封试验方案,并基于Fluent进行了数值模拟试验,探讨了各试验参数对端面开启力和泄漏率影响的显著性。研究结果表明:在试验参数范围内,影响端面开启力FO的显著因素为槽数Ng、槽长坝长比g、槽台宽比d和压差p;影响泄漏量Q的显著因素为槽数Ng、槽长坝长比g、槽台宽比d、转速n和压差p;具体表现为开启力随着槽长坝长比、槽台宽比、密封端面内外压差的增大呈上升趋势,随着槽数的增多呈下降趋势;泄漏量随着槽长坝长比、槽台宽比、转速、密封端面内外压差的增大呈上升趋势,随着槽数的增多而呈下降趋势。依据正交试验分析结果,提出了初步优化的密封端面型槽结构。

关键词: 自泵送机械密封, 正交试验, 数值模拟, 计算流体力学, 优化

Abstract:

A kind of self-pumping hydrodynamic mechanical seal, that the liquid inlet groove was arranged on the stationary ring and the dynamic pressure groove was distributed on the rotating ring, was put forward based on the principle of centrifugal pump. The experimental scheme of the self-pumping mechanical seals was designed by orthogonal test. The numerical simulation experiments were carried out based on Fluent, including discussing the significant effects of every parameter on the face opening force and the leakage rate. The numerical results showed that the groove number Ng, the ratio of groove length and dam length γ, the ratio of groove width and ridge width d, and the pressure p were the significant factors affecting the opening force FO and the leakage rate Q within the experimental ranges. Besides, the rotate speed n also affected Q significantly. Specifically, FO was increased with increasing g, d and p, while decreased with increasing Ng. The influence of g, d, p and Ng on Q was similar to that on FO. But Q was also increased with increasing n. The preliminary optimization of sealing structure was brought forward by analyzing the results of orthogonal test.

Key words: self-pumping mechanical seal, orthogonal test, numerical simulation, CFD, optimization

中图分类号: