矩形截面微模具通道中熔体的黏性耗散效应

doi:10.11949/j.issn.0438-1157.20161529

摘要/Abstract

摘要：

基于对微注塑成型过程中聚合物熔体充模流动时黏性耗散效应的理论分析，以聚丙烯（PP）和高密度聚乙烯（HDPE）两种聚合物材料，在不同工艺参数作用下流经不同当量直径和长径比矩形截面微模具通道时，由黏性耗散效应引起的微通道中熔体温度变化进行了试验测量和数值模拟。结果显示，微通道出口熔体温度的试验测量和数值模拟值与理论计算值非常吻合，且其平均误差小于1℃。同时研究发现，增大微模具通道当量直径和长径比时，熔体流动时的黏性耗散热量增多，通道出口熔体温度升高；而当微通道几何尺寸一定时，其黏性耗散热量随注射速度和注射压力的升高而增加，随熔体温度和模具温度的升高而降低；但同样试验条件下，对剪切作用敏感性强的PP材料的黏性耗散热量明显高于对剪切敏感性弱的HDPE材料。

关键词: 微通道, 非牛顿流体, 黏性耗散, 试验测量, 数值模拟

Abstract:

Based on the theoretical analysis of viscous dissipation effect when polymer melt flowing in micro injection mold, the change of the melt temperature of the polypropylene (PP) and high density polyethylene (HDPE) caused by the viscous dissipation effect were tested and simulated in the rectangular cross section micro channels with different equivalent diameters and ratios of length to diameter under a variety of process parameters. The results showed that the theoretical calculation and numerical simulation values were highly consistent with the test results, and the average errors were all less than 1℃. The study found that when the equivalent diameter and ratios of length to diameter were increased, the heat of viscous dissipation increased,thus the outlet temperature of channel rose. When the geometry size of the micro channels remains unchanged, the viscous dissipation heat increased with the increase of the injection speed and injection pressure, and decreased with the increase of the melt temperature and mold temperature. But under the same test condition, the viscous dissipation heat of PP material which is more sensitive to shear was obviously higher than that of HDPE.

Key words: microchannels, non-Newtonian fluids, viscous dissipation, experimental measurement, numerical simulation

中图分类号:

TQ311
TG76

于同敏, 张拯恺, 邹德健. 矩形截面微模具通道中熔体的黏性耗散效应[J]. 化工学报, 2017, 68(4): 1306-1317.

YU Tongmin, ZHANG Zhengkai, ZOU Dejian. Viscous dissipation effect of polymer melt in a rectangular cross section micro mold channel[J]. CIESC Journal, 2017, 68(4): 1306-1317.

参考文献 32

[1]	KOO J, KLEINSTREUER C. Liquid flow in microchannels:experimental observations and computational analyses of microfluidics effects[J]. Journal of Micromechanics & Microengineering, 2003, 13(5):568-579.
[2]	MORINI G L. Viscous heating in liquid flows in micro-channels[J]. International Journal of Heat & Mass Transfer, 2005, 48(17):3637-3647.
[3]	XU B, OOI K T, MAVRIPLIS C, et al. Viscous dissipation effects for liquid flow in microchannels[J]. Nanotech, 2002, 6:100-103.
[4]	HASSAN H, REGNIER N, PUJOS C, et al. Effect of viscous dissipation on the temperature of the polymer during injection molding filling[J]. Polymer Engineering & Science, 2008, 48(6):1199-1206.
[5]	庄俭, 于同敏, 王敏杰,等. 微注塑成型中对流换热系数对熔体充模流动的影响[J]. 高分子材料科学与工程, 2007, 23(6):169-172.ZHUANG J, YU T M, WANG M J, et al. Study on effects of heat transfer coefficient between polymer and mold on melt filling flow in micro injection molding[J]. Polymer Materials Science and Engineering, 2007, 23(6):169-172.
[6]	DAISUKE K, YUTAKA A. First law analysis for viscous dissipation in liquid flows in micro-channels[J]. International Journal of Heat and Mass Transfer, 2012, 55(9):2244-2248.
[7]	SADEGHI A, SAIDI M H. Viscous dissipation effects on thermal transport characteristics of combined pressure and electroosmotically driven flow in microchannels[J]. International Journal of Heat and Mass Transfer, 2010, 53(19):3782-3791.
[8]	SHOKOUHMAND H, SOLEIMANI M. The effect of viscous dissipation on temperature profile of a power-law fluid flow over a moving surface with arbitrary injection/suction[J]. Energy Conversion and Management, 2011, 52(1):171-179.
[9]	管宁, 刘志刚, 梁世强. 微管中液态流动的粘性耗散效应研究[J]. 自然科学进展, 2008, 18(11):1298-1303.GUAN N, LIU Z G, LIANG S Q. Study on viscous dissipation effect of liquid flow in micro tubes[J]. Progress in Natural Science, 2008, 18(11):1298-1303.
[10]	贺建坤, 孙立, 梁世强, 等. 粘性耗散对微管内部液体温升影响的实验研究[J].试验流体力学, 2008, 22(4):53-57.HE J K, SUN L, LIANG S Q, et al. Experimental investigation on the influence of viscous dissipation on liquid temperature rise in micro tube[J]. Journal of Experiments in Fluid Mechanics, 2008, 22(4):53-57.
[11]	贺建坤. 石英微管内的流动及换热特性的试验研究[D]. 淄博:山东理工大学, 2008.HE J K. Experimental study on flow and heat transfer characteristics in quartz micro-tube[D]. Zibo:Shandong University of Technology, 2008.
[12]	刘志刚, 赵孝保, 张承武. 黏性耗散效应对微石英管内部对流换热的影响[J]. 化工学报, 2007, 58(9):2194-2199.LIU Z G, ZHAO X B, ZHANG C W. Influence of viscous dissipation on convective heat transfer in quartz glass micro tube[J]. Journal of Chemical Industry and Engineering(China), 2007, 58(9):2194-2199.
[13]	布文峰, 刘志刚, 赵耀华. 微管内部流动粘性耗散的试验研究与数值模拟[J]. 哈尔滨工业大学学报, 2008, 40(1):160-163.BU W F, LIU Z G, ZHAO Y H. Experimental study and numerical simulation of viscous dissipation effect for flow in micro tube[J]. Journal of Harbin Institute of Technology, 2008, 40(1):160-163.
[14]	徐斌, 于同敏, 王敏杰, 等. 微尺度聚合物熔体粘性耗散效应对流变行为的影响[J]. 机械工程学报, 2010, 46(14):47-52.XU B, YU T M, WANG M J, et al. Impact of viscous dissipation effects on micro-scale polymer melts rheological behavior[J]. Journal of Mechanical Engineering, 2010, 46(14):47-52.
[15]	徐斌, 王敏杰, 于同敏, 等. 微通道聚合熔体粘性耗散尺度效应[J]. 高分子材料科学与工程, 2014, 30(7):105-109.XU B, WANG M J, YU T M, et al. Viscous dissipation scale effect on polymer melt in micro channels[J]. Polymer Material Science and Engineering, 2014, 30(7):105-109.
[16]	刘丽昆, 刘赵淼, 申峰. 几何参数对微通道黏性耗散影响的研究[C]//北京力学会第19届学术年会论文集. 北京:北京力学会, 2013:131-132.LIU L K, LIU Z M, SHEN F. Study on the effect of micro channel geometric parameters on the viscous dissipation[C]//Proceedings of the 19 Annual Academic Conference of Beijing Society of Theoretical and Applied Mechanics. Beijing:Beijing Society of Theoretical and Applied Mechanics, 2013:131-132.
[17]	于同敏, 武永强, 王敏杰. 超声外场对微通道中熔体黏性耗散效应的影响[J]. 机械工程学报, 2015, 51(29):79-85.YU T M, WU Y Q, WANG M J. Impact of ultrasonic field on viscous dissipation effects of polymer melts in micro channel[J]. Journal of Mechanical Engineering, 2015, 51(29):79-85.
[18]	于同敏, 贝海鑫. 微注塑充模流动中的粘性耗散效应[J]. 高分子材料科学与工程, 2012, 28(12):164-168.YU T M, BEI H X. Viscous dissipation effects in micro-injection molding filling flow[J]. Polymer Material Science and Engineering, 2012, 28(12):164-168.
[19]	于同敏, 永恒, 贝海鑫, 等. 微尺度通道中聚合物熔体的黏性耗散效应[J]. 化工学报, 2013, 64(8):2781-2787.YU T M, YONG H, BEI H X, et al. Viscous dissipation effects of polymer melts in micro-channels[J]. CIESC Journal, 2013, 64(8):2781-2787.
[20]	徐华, 于同敏, 徐斌. 微注塑成型充模流动中的对流换热实验[J]. 高分子材料科学与工程, 2012, 28(1):109-112.XU H, YU T M, XU B. Experiment of convective heat transfer of filling flow in micro injection molding[J]. Polymer Material Science and Engineering, 2012, 28(1):109-112.
[21]	HUNG Y M. A comparative study of viscous dissipation effect on entropy generation in single-phase liquid flow in microchannels[J]. International Journal of Thermal Sciences, 2009, 48(5):1026-1035.
[22]	RIJ J V, AMEEL T, HARMAN T. An evaluation of secondary effects on microchannel frictional and convective heat transfer characteristics[J]. International Journal of Heat & Mass Transfer, 2009, 52(11/12):2792-2801.
[23]	杜东兴, 李志信, 过增元,等. 微细管内压力功及粘性耗散对流动特性的影响[J]. 清华大学学报(自然科学版), 1999, 39(11):58-60.DU D X, LI Z X, GUO Z Y, et al. Effect of reversible work and viscous dissipation on gas flow characteristics in a microtube[J]. Journal of Tsinghua University (Science and Technology), 1999, 39(11):58-60.
[24]	HOOMAN K, GORJI-BANDPY M. Laminar dissipative flow in a porous channel bounded by isothermal parallel plates[J]. Applied Mathematics and Mechanics (English Edition), 2005, 26(5):587-593.
[25]	魏玉新. 微注塑成型充模流动中粘性耗散与对流传热研究[D]. 大连:大连理工大学, 2006.WEI Y X. Research on viscous dissipation and heat transfer in micro injection molding[D]. Dalian:Dalian University of Technology, 2006.
[26]	张小华, 欧阳洁, 张林. 圆管聚合物热流中黏性耗散分析的无网格模拟[J]. 化工学报, 2007, 58(1):15-20.ZHANG X H, OUYANG J, ZHANG L. Meshless analysis on heat transfer with viscous dissipation in polymer flow in tube[J]. Journal of Chemical Industry and Engineering(China), 2007, 58(1):15-20.
[27]	贝海鑫. 微注塑充模流动中粘性耗散的研究[D]. 大连:大连理工大学, 2010.BEI H X. Viscous dissipation of the filling process in micro injection molding[J]. Dalian:Dalian University of Technology, 2010.
[28]	武永强. 超声对微熔体黏性耗散及对流换热影响的研究[D]. 大连:大连理工大学, 2015.WU Y Q. Study for the effect of ultrasonic on viscous dissipation and convective heat transfer of micro melt[D]. Dalian:Dalian University of Technology, 2015.
[29]	永恒. 基于超声外场的微注塑成型中粘性耗散的研究[D]. 大连:大连理工大学, 2013.YONG H. Effect of ultrasonic vibration on viscous dissipation in micro injection molding process[D]. Dalian:Dalian University of Technology, 2013.
[30]	DAWAON A, RIDES M, ALLEN C R G, et al. Polymer-mould interface heat transfer coefficient measurements for polymer processing[J]. Polymer Testing, 2008, 27(5):555-565.
[31]	NAKAO M, TSUCHIYA K, SADAMITSU T, et al. Heat transfer in injection molding for reproduction of sub-micron-sized features[J]. The International Journal of Advanced Manufacturing Technology, 2008, 38(3):426-432.
[32]	唐俊. 微注塑成型充模流动中熔体粘度和壁面滑移的研究[D]. 大连:大连理工大学, 2008.TANG J. Research on melt viscosity and wall-slip in micro-injection molding filling flow[D]. Dalian:Dalian University of Technology, 2008.