CaO-Ca9Al6O18吸收剂的碳酸化反应动力学

doi:10.3969/j.issn.0438-1157.2013.02.017

化工学报 ›› 2013, Vol. 64 ›› Issue (2): 532-538.DOI: 10.3969/j.issn.0438-1157.2013.02.017

• 催化、动力学与反应器 • 上一篇下一篇

CaO-Ca₉Al₆O₁₈吸收剂的碳酸化反应动力学

谢苗苗, 周志明, 祁阳, 程振民

华东理工大学, 化学工程联合国家重点实验室, 上海 200237

收稿日期:2012-07-18 修回日期:2012-08-20 出版日期:2013-02-05 发布日期:2013-02-05
通讯作者: 周志明
作者简介:谢苗苗(1987—),男,硕士研究生。
基金资助:
国家自然科学基金项目(21276076);化学工程联合国家重点实验室开放课题项目(SKL-ChE-10C06);中央高校基本科研业务费项目(WA1014003)。

Carbonation kinetics of CO₂ with CaO-Ca₉Al₆O₁₈ sorbent

XIE Miaomiao, ZHOU Zhiming, QI Yang, CHENG Zhenmin

State Key Laboratory of Chemical Engineering, East China University of Science and Technology, Shanghai 200237, China

Received:2012-07-18 Revised:2012-08-20 Online:2013-02-05 Published:2013-02-05
Supported by:
supported by the National Natural Science Foundation of China(21276076), the State Key Laboratory of Chemical Engineering(SKL-ChE-10C06) and the Fundamental Research Funds for the Central Universities(WA1014003).

摘要/Abstract

摘要： 以柠檬酸钙和硝酸铝为前体,采用湿法混合法制备了CaO质量分数为80%的CaO-Ca₉Al₆O₁₈吸收剂,并对其CO₂吸收性能进行了研究。结果表明,CaO-Ca₉Al₆O₁₈具有优异的CO₂吸收容量和长周期循环使用稳定性,经过50次循环使用后,其转化率仍保持在78%以上,远优于传统的CaO吸收剂。在500～700℃和CO₂分压为0.005～0.015 MPa条件下,研究了CaO-Ca₉Al₆O₁₈吸收剂的碳酸化反应动力学,分别采用离子反应模型和表观模型描述化学反应动力学控制阶段(快反应段)和产物层扩散阶段(慢反应段)。实验测得的吸收剂转化率与模型预测值吻合较好,快慢反应段的活化能分别为25.6、57.7 kJ·mol^-1。该动力学模型可准确模拟CaO-Ca₉Al₆O₁₈吸收剂在长周期循环使用条件下的碳酸化反应。

关键词: CaO-Ca₉Al₆O₁₈, CO₂吸收剂, 稳定性, 碳酸化反应, 动力学模型

Abstract: A CaO-Ca₉Al₆O₁₈ sorbent with a mass fraction of CaO of 80% was prepared by the wet mixing method.Calcium citrate and aluminum nitrate were used as calcium and aluminum precursors, respectively. The CO₂ capture performance of the sorbent was investigated by using thermogravimetry.The results showed that the CaO-Ca₉Al₆O₁₈ sorbent exhibited excellent CO₂ capture capacity and long-term cyclic stability, and its conversion remained above 77% after 50 consecutive cyclic operations, which was much better than that of conventional CaO sorbent.The carbonation kinetics between CO₂ and the CaO-Ca₉Al₆O₁₈ sorbent was then studied over a temperature range of 500—700℃ and CO₂ partial pressure of 0.005—0.015 MPa.The fast reaction regime (controlled by chemical reaction) and the slow reaction regime (controlled by diffusion) of the carbonation reaction were successfully described by an ion reaction model and an apparent model, respectively, and the corresponding activation energies were 25.6 kJ·mol^-1 and 57.7 kJ·mol^-1, respectively.The predicted conversions of the CaO-Ca₉Al₆O₁₈ sorbent agreed well with the experimental data.Finally, the kinetic model established was successfully used to predict the carbonation reaction of long-term cyclic operation.

Key words: CaO-Ca₉Al₆O₁₈, CO₂ sorbent, stability, carbonation, kinetic model

中图分类号:

TQ530
TQ037

谢苗苗, 周志明, 祁阳, 程振民. CaO-Ca₉Al₆O₁₈吸收剂的碳酸化反应动力学[J]. 化工学报, 2013, 64(2): 532-538.

XIE Miaomiao, ZHOU Zhiming, QI Yang, CHENG Zhenmin. Carbonation kinetics of CO₂ with CaO-Ca₉Al₆O₁₈ sorbent[J]. CIESC Journal, 2013, 64(2): 532-538.

参考文献 18

[1]	Blamey J, Anthony E J, Wang J, Fennell P S.The calcium looping cycle for large-scale CO2 capture[J].Prog. Energy Combust.Sci., 2010, 36:260-279
[2]	Manovic V, Anthony E J.Lime-based sorbents for high-temperature CO2 capture － a review of sorbent modification methods[J].Int.J.Environ.Res.Public Health, 2010, 7:3129-3140
[3]	Liu W Q, Feng B, Wu Y Q, Wang G X, Barry J, Diniz Da,Costa J C.Synthesis of sintering-resistant sorbents for CO2 capture[J].Environ.Sci.Technol., 2010, 44:3093-3097
[4]	Gruene P, Belova A G, Yegulalp T M, Farrauto R J, Castaldi M J.Dispersed calcium oxide as a reversible and efficient CO2-sorbent at intermediate temperatures[J].Ind.Eng.Chem.Res., 2011, 50:4042-4049
[5]	Li Z S, Cai N S, Huang Y Y, Han H J.Synthesis, experimental studies, and analysis of a new calcium-based carbon dioxide absorbent[J].Energy & Fuels, 2005, 19:1447-1452
[6]	Li Y J, Zhao C S, Chen H C, Duan L B, Chen X P.Cyclic CO2 capture behavior of KMnO4-doped CaO-based sorbent[J].Fuel, 2010, 89:642-649
[7]	Wu S F, Zhu Y Q.Behavior of CaTiO3/nano-CaO as a CO2 reactive adsorbent[J].Ind.Eng.Chem.Res., 2010, 49:2701-2706
[8]	Martavaltzi C S, Lemonidou A A.Parameter study of the CaO-Ca12Al14O33 synthesis with respect to high CO2 sorption capacity and stability on multicycle operation[J].Ind.Eng.Chem.Res., 2008, 47:9537-9543
[9]	Zhou Z M, Qi Y, Xie M M, Cheng Z M, Yuan W K.Synthesis of CaO-based sorbents through incorporation of alumina/aluminate and their CO2 capture performance[J].Chem.Eng.Sci., 2012, 74:172-180
[10]	Li Zhenshan(李振山),Cai Ningsheng(蔡宁生),Zhao Xudong(赵旭东),Huang Yuyu(黄煜煜).Kinetic characteristic of the multiple carbonation cycle reactions of CaO with CO2[J].Journal of Combustion Science and Technology(燃烧科学与技术), 2006, 12(6):481-485
[11]	Bhatia S K, Perlmutter D D.Effect of the product layer on the kinetics of the CO2-lime reaction[J].AIChE J., 1983, 29:79-86
[12]	Lee D K.An apparent kinetic model for the carbonation of calcium oxide by carbon dioxide[J].Chem.Eng.J., 2004, 100:71-77
[13]	Wu S F, Lan P Q.A kinetic model of nano-CaO reactions with CO2 in a sorption complex catalyst[J].AIChE J., 2012, 58:1570-1577
[14]	Xie M M, Zhou Z M, Qi Y, Cheng Z M, Yuan W K. Sorption-enhanced steam methane reforming by in situ CO2 capture on a CaO-Ca9Al6O18 sorbent[J].Chem. Eng. J., 2012, 207/208:142-150
[15]	Grasa G, Murillo R, Alonso M, Abanades J C.Application of the random pore model to the carbonation cyclic reaction[J].AIChE J., 2009, 55:1246-1255
[16]	Sun P, Grace J R, Lim C J, Anthony E J.Determination of intrinsic rate constants of the CaO-CO2 reaction[J].Chem.Eng.Sci., 2008, 63:47-56
[17]	Gupta H, Fan L S.Carbonation-calcination cycle using high reactivity calcium oxide for carbon dioxide separation from flue gas[J].Ind.Eng.Chem.Res., 2002, 41:4035-4042
[18]	Shi Qi(师琦),Wu Sufang(吴素芳),Jiang Mingzhe(蒋明哲),Li Qinghui(李清辉).Reactive sorption-decomposition kinetics of nano Ca-based CO2 sorbents[J].CIESC Journal(化工学报), 2009, 60(3):641-648

CaO-Ca₉Al₆O₁₈吸收剂的碳酸化反应动力学

Carbonation kinetics of CO₂ with CaO-Ca₉Al₆O₁₈ sorbent

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献 18

相关文章 15

编辑推荐

Metrics

本文评价

[1]	江河, 袁俊飞, 王林, 邢谷雨. 均流腔结构对微细通道内相变流动特性影响的实验研究[J]. 化工学报, 2023, 74(S1): 235-244.
[2]	金正浩, 封立杰, 李舒宏. 氨水溶液交叉型再吸收式热泵的能量及分析[J]. 化工学报, 2023, 74(S1): 53-63.
[3]	李锦潼, 邱顺, 孙文寿. 煤浆法烟气脱硫中草酸和紫外线强化煤砷浸出过程[J]. 化工学报, 2023, 74(8): 3522-3532.
[4]	郑玉圆, 葛志伟, 韩翔宇, 王亮, 陈海生. 中高温钙基材料热化学储热的研究进展与展望[J]. 化工学报, 2023, 74(8): 3171-3192.
[5]	孟令玎, 崇汝青, 孙菲雪, 孟子晖, 刘文芳. 改性聚乙烯膜和氧化硅固定化碳酸酐酶[J]. 化工学报, 2023, 74(8): 3472-3484.
[6]	蔡斌, 张效林, 罗倩, 党江涛, 左栗源, 刘欣梅. 导电薄膜材料的研究进展[J]. 化工学报, 2023, 74(6): 2308-2321.
[7]	李艳辉, 丁邵明, 白周央, 张一楠, 于智红, 邢利梅, 高鹏飞, 王永贞. 非常规服役超临界锅炉的微纳尺度腐蚀动力学模型建立及应用[J]. 化工学报, 2023, 74(6): 2436-2446.
[8]	毛磊, 刘冠章, 袁航, 张光亚. 可捕集CO₂的纳米碳酸酐酶粒子的高效制备及性能研究[J]. 化工学报, 2023, 74(6): 2589-2598.
[9]	徐文超, 孙志高, 李翠敏, 李娟, 黄海峰. 静态条件下表面活性剂E-1310对HCFC-141b水合物生成的影响[J]. 化工学报, 2023, 74(5): 2179-2185.
[10]	王承泽, 顾凯丽, 张晋华, 石建轩, 刘艺娓, 李锦祥. 硫化协同老化零价铁增效去除水中Cr（Ⅵ）的作用机制[J]. 化工学报, 2023, 74(5): 2197-2206.
[11]	王子健, 柯明, 李佳涵, 李舒婷, 孙巾茹, 童燕兵, 赵治平, 刘加英, 任璐. 短b轴ZSM-5分子筛制备方法及应用研究进展[J]. 化工学报, 2023, 74(4): 1457-1473.
[12]	刘润竹, 储甜甜, 张孝阿, 王成忠, 张军营. α，ω-端羟基亚苯基氟硅聚合物的合成及性能[J]. 化工学报, 2023, 74(3): 1360-1369.
[13]	陈向上, 马振杰, 任希华, 贾悦, 吕晓龙, 陈华艳. 三维网络萃取膜的制备及传质效率研究[J]. 化工学报, 2023, 74(3): 1126-1133.
[14]	郑杰元, 张先伟, 万金涛, 范宏. 丁香酚环氧有机硅树脂的制备及其固化动力学研究[J]. 化工学报, 2023, 74(2): 924-932.
[15]	周桓, 张梦丽, 郝晴, 吴思, 李杰, 徐存兵. 硫酸镁型光卤石转化钾盐镁矾的过程机制与动态规律[J]. 化工学报, 2022, 73(9): 3841-3850.