组合约束型提升管出口气固分布器的压降

doi:10.3969/j.issn.0438-1157.2014.09.009

化工学报 ›› 2014, Vol. 65 ›› Issue (9): 3375-3382.DOI: 10.3969/j.issn.0438-1157.2014.09.009

组合约束型提升管出口气固分布器的压降

贾梦达^1,2, 王德武¹, 张少峰^1,2, 赵立军¹, 李睿¹, 吴广恒¹

1 河北工业大学化工学院, 天津 300130;
2 河北工业大学海水资源高效利用化工技术教育部工程研究中心, 天津 300130

收稿日期:2013-12-29 修回日期:2014-03-13 出版日期:2014-09-05 发布日期:2014-09-05
通讯作者: 王德武
基金资助:
国家自然科学基金项目（21106028）；河北省自然科学基金项目（B2013202125）。

Pressure drop of gas-solids distributor located at outlet of riser with combined restraint

JIA Mengda^1,2, WANG Dewu¹, ZHANG Shaofeng^1,2, ZHAO Lijun¹, LI Rui¹, WU Guangheng¹

1 School of Chemical Engineering, Hebei University of Technology, Tianjin 300130, China;
2 Engineering Research Center of Seawater Utilization Technology of Ministry of Education, Hebei University of Technology, Tianjin 300130, China

Received:2013-12-29 Revised:2014-03-13 Online:2014-09-05 Published:2014-09-05
Supported by:
supported by the National Natural Science Foundation of China (21106028) and the Natural Science Foundation of Hebei Province (B2013202125).

摘要/Abstract

摘要： 在一套组合约束型提升管冷态实验装置上，通过实验研究了不同操作条件下提升管出口气固分布器的压降，并与常规气体分布器压降进行了对比。实验结果表明，在零床层及有床层的操作模式下，气固分布器压降均随提升管内表观气速和颗粒循环强度的增加而增大，在颗粒循环强度较低时，气固分布器压降曲线变化的斜率随着表观气速的增加而增大，在颗粒循环强度较高时，气固分布器压降曲线变化的斜率随着表观气速的增加而减小；随着开孔率及上部流化床层压降增加，气固分布器压降呈降低趋势，当流化床层压降达到一定程度后，分布器各孔方可实现有效布气，此后气固分布器压降趋于近似不变；在相同表观气速及开孔率下，气固分布器压降大于常规气体分布器压降。

关键词: 流化床, 提升管, 出口结构, 气固分布器, 压降

Abstract: Based on a cold model experimental setup of riser reactor with combined restraint outlet, an experiment was conducted to analyze pressure drop of gas-solids distributor at the outlet of riser under different circumstances. Gas-solids distributor's pressure drop increased with increasing superficial gas velocity and solids flux, with or without active operating bed. The slope of gas-solids distributor's pressure drop curve increased with increasing superficial gas velocity at lower solids flux, while decreased at higher solids flux. Pressure drop of the distributor declined with increasing distributor's aperture ratio and increasing pressure drop of the upper fluidized bed. When the pressure drop of the upper fluidized bed increased to a specific value, the holes of the distributor were all able to be passed through by gas-solids flow, with the distributor pressure drop approximately unchangeable. At the same superficial gas velocity, pressure drop of gas-solids distributor was bigger than that of conventional gas distributor.

Key words: fluidized-bed, riser, exit constructure, gas-solids distributor, pressure drop

中图分类号:

贾梦达, 王德武, 张少峰, 赵立军, 李睿, 吴广恒. 组合约束型提升管出口气固分布器的压降[J]. 化工学报, 2014, 65(9): 3375-3382.

JIA Mengda, WANG Dewu, ZHANG Shaofeng, ZHAO Lijun, LI Rui, WU Guangheng. Pressure drop of gas-solids distributor located at outlet of riser with combined restraint[J]. CIESC Journal, 2014, 65(9): 3375-3382.

参考文献 21

[1]	Richardson D R. How to design fluid flow distributors [J]. Chemical Engineering, 1961, 68 (9): 83-88
[2]	Geldart D, Baeyens J. The design of distributors for gas fluidized beds [J]. Powder Technology, 1985, 42 (1): 6-12
[3]	Zhao Tong, Takei M. Discussion of the solids distribution behavior in a downer with new designed distributor based on concentration images obtained by electrical capacitance tomography [J]. Powder Technology, 2010, 1 (198): 120-130
[4]	Siegel R. Effect of distributor plate-to-bed resistance ratio on onset of fluidized-bed channeling [J]. AIChE J., 1976, 22 (3): 590-596
[5]	Kumar A, Roy G K. Distributor to bed pressure drop ratio in promoted gas-solid fluidized beds [J]. Journal of the Institution of Engineers, 2007, 87 (3): 11-15
[6]	Feng Bingxiao (冯冰潇), Miao Zhengqing (缪正清), Pan Jiaquan (潘家泉), Yu Zhongyi (于忠义), Zhang Min (张民), Zheng Dianbin (郑殿斌). Test obtained pressure drop characteristics of three typical distributor plate nozzles in circulating fluidized bed boilers [J]. Power Engineering (动力工程), 2008, 28 (1) : 24-27
[7]	Zhang Cuiyu (张翠玉), Zhao Yuemin (赵跃民), Luo Zhenfu (骆振福), Duan Chenlong (段晨龙), Xing Hongbo (邢洪波). Study on fluidized feature of gas distributor applied to dry coal preparation [J]. Coal Engineering (煤炭工程), 2011 (2): 91-93
[8]	Wang Zhangmao (王樟茂), Zhang Nianying (张年英), Lü Dewei (吕德伟), Chen Gantang (陈甘棠), Liu Qing (刘青), Jiang Yinrui (江银瑞), Lai Chenglie (赖成烈). Study on combined porous gas distributor of fluidized bed [J]. Petrochemical Engineering (石油化工), 1986, 15 (7): 399-405
[9]	Dong Shuqin (董淑芹), Si Chongdian (司崇殿), Cao Changqing (曹长青). Flow characteristics in gas-solid fluidized bed affected by perforated ratios of distributor [J]. Chemical Reaction Engineering and Technology (化学反应工程与工艺), 2008, 24 (5): 433-439
[10]	Sathiyamoorthy D, Rao Ch S. Gas distributors in fluidized bed [J]. Powder Technology, 1978, 20 (2): 47-53
[11]	Shilapuram V, Sai P S T. Axial solids holdup distribution in a liquid-solid circulating fluidized bed: effect of the liquid distributor, method of operation, and viscosity of the fluidizing media [J]. Industrial and Engineering Chemistry Research, 2012, 50 (51): 16242-16250
[12]	Soria-Verdugo A, Garcia H N, Almendros-Ibanez J A, Ruiz-Rivas U. Motion of a large object in a bubbling fluidized bed with a rotating distributor [J]. Chemical Engineer and Processing: Process Intensification, 2011, 8 (50): 859-868
[13]	Lu Bona (鲁波娜), Cheng Congli (程从礼), Lu Weimin (鲁维民), Wang Wei (王维), Xu Youhao (许友好). Numerical simulation of reaction process in MIP riser based on multi-scale model [J]. CIESC Journal (化工学报), 2013, 64 (6): 1983-1992
[14]	Wang Wei (王巍), Xie Chaogang (谢朝钢). Development and application of DCC new technology [J]. Techno-Economics in Petrochemicals (石油化工技术经济), 2005, 21 (1): 8-12
[15]	Bai Yuehua (白跃华), Gao Jinsen (高金森), Li Shengchang (李盛昌), Xu Chunming (徐春明). Commercial application of subsidary riser for FCC naphtha olefin reduction [J]. Petroleum Processing and Petrochemicals (石油炼制与化工), 2004, 35 (10): 17-21
[16]	Wang Dewu (王德武), Lu Chunxi (卢春喜). Study on particle flow behavior and restriction in back mixing region of a riser fluidized bed coupled reactor [J]. Journal of Chemical Industry and Engineering (China) (化工学报), 2008, 59 (4): 859-865
[17]	Wang Dewu (王德武), Zhang Haiguang (张海光), Lu Chunxi (卢春喜). Particle velocity distribution and restriction in riser section of a riser fluidized bed coupled reactor [J]. Journal of Chemical Industry and Engineering (China) (化工学报), 2008, 59 (12): 3042-3049
[18]	Wang Dewu (王德武), Lu Chunxi (卢春喜). Radial distribution and axial development of solids hold up in the riser coupled with fluidized bed [J]. The Chinese Journal of Process Engineering (过程工程学报), 2008, 8 (2): 86-92
[19]	Zhang Aiguo (张爱国), Zhao Yubing (赵予兵), Lu Chunxi (卢春喜), Wang Dewu (王德武).Comparison of flow characteristics between compound and conventional gas-solid loop fluidized beds [J]. Petroleum Processing and Petrochemicals (石油炼制与化工), 2007, 42 (9): 17-23
[20]	Issangya A S. Flow dynamics in high density circulating fluidized beds [D]. Vancouver: University of British Columbia, 1998
[21]	Lu Chunxi (卢春喜), Wang Zhu'an (王祝安). Technology of Catalytic Cracking Fluidization (催化裂化流态化技术) [M]. Beijing: Chine Petrochemical Press, 2002: 70

组合约束型提升管出口气固分布器的压降

Pressure drop of gas-solids distributor located at outlet of riser with combined restraint

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献 21

相关文章 15

编辑推荐

Metrics

本文评价

[1]	江河, 袁俊飞, 王林, 邢谷雨. 均流腔结构对微细通道内相变流动特性影响的实验研究[J]. 化工学报, 2023, 74(S1): 235-244.
[2]	高金明, 郭玉娇, 鄂承林, 卢春喜. 一种封闭罩内顺流多旋臂气液分离器的分离特性研究[J]. 化工学报, 2023, 74(7): 2957-2966.
[3]	张媛媛, 曲江源, 苏欣欣, 杨静, 张锴. 循环流化床燃煤机组SNCR脱硝过程气液传质和反应特性[J]. 化工学报, 2023, 74(6): 2404-2415.
[4]	杨峥豪, 何臻, 常玉龙, 靳紫恒, 江霞. 生物质快速热解下行式流化床反应器研究进展[J]. 化工学报, 2023, 74(6): 2249-2263.
[5]	郑志航, 马郡男, 闫子涵, 卢春喜. 提升管射流影响区内压力脉动特性研究[J]. 化工学报, 2023, 74(6): 2335-2350.
[6]	陈巨辉, 张谦, 舒崚峰, 李丹, 徐鑫, 刘晓刚, 赵晨希, 曹希峰. 基于DEM方法的旋转流化床纳米颗粒流动特性研究[J]. 化工学报, 2023, 74(6): 2374-2381.
[7]	袁子涵, 王淑彦, 邵宝力, 谢磊, 陈曦, 马一玫. 基于幂律液固曳力模型流化床内湿颗粒流动特性的研究[J]. 化工学报, 2023, 74(5): 2000-2012.
[8]	白剑钊, 郭子轩, 王德武, 刘燕, 王若瑾, 唐猛, 张少峰. 摇摆对气液并流模式立体旋流筛板压降的影响研究[J]. 化工学报, 2023, 74(2): 707-720.
[9]	王凯玥, 马永丽, 李琛, 刘明言. 气液固微型流化床的气液传质系数[J]. 化工学报, 2022, 73(8): 3529-3540.
[10]	张东旺, 杨海瑞, 周托, 黄中, 李诗媛, 张缦. 生物质锅炉对流受热面积灰冷态模拟实验研究[J]. 化工学报, 2022, 73(8): 3731-3738.
[11]	刘新华, 韩振南, 韩健, 梁斌, 张楠, 胡善伟, 白丁荣, 许光文. 基于热解与燃烧反应重构的低NO _x 解耦燃烧原理与技术[J]. 化工学报, 2022, 73(8): 3355-3368.
[12]	王刚, 夏志豪, 李希艳, 张虹, 韩振南, 宋兴飞, 许光文. 不同气氛下流化床菱镁矿轻烧产物特性研究[J]. 化工学报, 2022, 73(8): 3699-3707.
[13]	禹言芳, 刘桓辰, 孟辉波, 刘励图, 李毓, 吴剑华. Lightnin静态混合器内气泡分散流体动力学特性实验研究[J]. 化工学报, 2022, 73(8): 3565-3575.
[14]	朱莲峰, 王超, 张梦娟, 刘方正, 贾鑫, 安萍, 许光文, 韩振南. 水蒸气/氧流化床两段煤气化制备低焦油合成气工艺实验[J]. 化工学报, 2022, 73(8): 3720-3730.
[15]	牛犁, 刘梦溪, 王海北. 密相流化床中介尺度流动结构的流体力学特性研究[J]. 化工学报, 2022, 73(6): 2622-2635.