含气泡油滴撞击矩形沟槽壁面的数值分析

doi:10.11949/j.issn.0438-1157.20180620

化工学报 ›› 2018, Vol. 69 ›› Issue (12): 5011-5023.DOI: 10.11949/j.issn.0438-1157.20180620

含气泡油滴撞击矩形沟槽壁面的数值分析

周剑宏¹, 童宝宏¹, 王伟², 刘焜², 苏家磊¹

1. 安徽工业大学机械工程学院, 安徽马鞍山 243032;
2. 合肥工业大学机械工程学院摩擦学研究所, 安徽合肥 230009

收稿日期:2018-06-06 修回日期:2018-08-22 出版日期:2018-12-05 发布日期:2018-12-05
通讯作者: 童宝宏
基金资助:
国家自然科学基金项目（51475135，11472096）；摩擦学国家重点实验室开放基金项目（SKLTKF17B01）；安徽工业大学研究生创新基金项目（2017014）。

Numerical analysis of hollow oil droplet impact on rectangular groove surface

ZHOU Jianhong¹, TONG Baohong¹, WANG Wei², LIU Kun², SU Jialei¹

1. School of Mechanical Engineering, Anhui University of Technology, Maanshan 243032, Anhui, China;
2. Institute of Tribology, School of Mechanical Engineering, Hefei University of Technology, Heifei 230009, Anhui, China

Received:2018-06-06 Revised:2018-08-22 Online:2018-12-05 Published:2018-12-05
Supported by:
supported by the National Natural Science Foundation of China (51475135, 11472096), the Tribology Science Fund of State Key Laboratory of Tribology (SKLTKF17B01) and the Graduate Innovation Foundation of Anhui University of Technology (2017014).

摘要/Abstract

摘要：

采用耦合水平集-体积分数（CLSVOF）方法对含气泡油滴撞击矩形沟槽壁面现象进行数值模拟研究，考察了油滴撞击壁面后的形态演化过程，分析了中心射流形成机理和气体夹带的分布规律，并探究了沟槽宽度、沟槽深度和撞击位置对油滴铺展特性的影响。研究表明：含气泡油滴在矩形沟槽壁面铺展时会形成中心射流，沟槽内部存在气体夹带现象。气泡底部的速度旋涡是形成中心射流的主要原因，沟槽内的气体夹带受油滴铺展速度影响呈现规律性分布。沟槽宽度对含气泡油滴在垂直沟槽方向和平行沟槽方向的铺展长度影响较大，但对铺展高度影响较小。当无量纲沟槽宽度为0.3时，油滴形成颈部射流并在运动后期使垂直沟槽方向的铺展长度迅速增加。此外，沟槽深度也对含气泡油滴在各方向的铺展有重要影响，沟槽深度越大，中心射流现象越难形成。撞击位置变化不改变油滴在沟槽壁面上的运动演化过程，但对沟槽内部的气体夹带规律有一定影响。

关键词: 油滴撞壁, 气泡, 中心射流, 气体夹带, 动力学, 数值模拟

Abstract:

The behavior of the hollow oil droplets impinging on the rough surface often take place in the oil-gas lubricating system, which will affect the quality of the oil film formation on the surface of the friction pairs. The coupled level set and volume-of-fraction (CLSVOF) method is used to simulate this behavior. The formation mechanism of the central jet and the distribution of air entrainment are analyzed. And the effects of grooved width, grooved depth and impact position on the oil droplet spreading process are investigated. The results show that the central jet and air entrainment can be formed after the hollow oil droplet rectangular groove surface. The formation of the central jet originates from the velocity vortex at the bottom of impacting on the bubble. The position of air entrainment in the grooves is influenced by the spreading velocity of the hollow oil droplet. When the dimensionless grooved width A_g is less than 0.2 or equal to 0.4, the spreading coefficient of vertical grooves D_x of the hollow oil droplet is approximately same. However, when the dimensionless grooved width is equal to 0.3, the spreading coefficient of vertical grooves D_x increases rapidly in the later period of movement due to the formation of a neck jet on the grooved surface. In addition, the spreading coefficient of parallel grooves D_z increases with the increase of grooved width. The spreading height coefficient D_y of the oil droplet is consistent on each surface and is not affected by the grooved width. When the dimensionless grooved depth H_g ≤ 0.2, the spreading coefficient of vertical groove D_x decreases with the depth of groove increasing. When the dimensionless grooved depth H_g>0.2, the spreading coefficient of vertical grooves D_x is almost equal. However, with the increase of grooved depth, the spreading coefficient of parallel grooves D_z is decreased. The spreading height coefficient D_y of the hollow oil droplet decreases with the increase of the grooved depth, and the increase of the grooved depth can prevent the formation of the central jet. The effects of the impact position on the distribution of air entrainment are significant, while the movement of hollow oil droplet plays a negligible role in them.

Key words: oil droplet impact, bubble, central jet, air entrainment, kinetics, numerical simulation

中图分类号:

O359

周剑宏, 童宝宏, 王伟, 刘焜, 苏家磊. 含气泡油滴撞击矩形沟槽壁面的数值分析[J]. 化工学报, 2018, 69(12): 5011-5023.

ZHOU Jianhong, TONG Baohong, WANG Wei, LIU Kun, SU Jialei. Numerical analysis of hollow oil droplet impact on rectangular groove surface[J]. CIESC Journal, 2018, 69(12): 5011-5023.

参考文献 30

[1]	王建文, 安琦. 油气润滑输送中两相流的形成[J]. 华东理工大学学报, 2009, 35(2):324-327. WANG J W, AN Q. Investigation of two-phase flow regimes in transport pipe in oil-air lubrication system[J]. J. East China Univ. Sci. Techno.(Nat. Sci. Ed.), 2009, 35(2):324-327.
[2]	GULYAEV I P, SONLONENKO O P. Hollow droplets impacting onto a solid surface[J]. Experiments in Fluids, 2013, 54(1):1432.
[3]	GULYAEV I P, SOLONENKO O P, GULYAEV P Y, et al. Hydrodynamic features of the impact of a hollow spherical drop on a flat surface[J]. Technical Physics Letters, 2009, 35(10):885-888.
[4]	CHEREPANOV A N, SOLONENKO O P, BUBLIK V V. Numerical and analytic investigation of the dynamics of hollow droplet impact onto substrate[J]. Thermophysics and Aeromechanics, 2008, 15(4):631-641.
[5]	郑志伟, 李大树, 仇性启, 等. 中空液滴碰撞水平壁面数值分析[J]. 物理学报, 2017, 66(1):014704. ZHENG Z W, LI D S, QIU X Q, et al. Numerical analysis of hollow droplet impact on a flat Surface[J]. Acta Phys. Sin., 2017, 66(1):014704.
[6]	KUMAR A, GU S, KAMNIS S. Simulation of impact of a hollow droplet on a flat surface[J]. Applied Physics A, 2012, 109(1):101-109.
[7]	LI X, MA X, LAN Z. Dynamic behavior of the water droplet impact on a textured hydrophobic/superhydrophobic surface:the effect of the remaining liquid film arising on the pillars' tops on the contact time[J]. Langmuir, 2010, 26(7):4831-4838.
[8]	KANNAN R, SIVAKUMAR D. Impact of liquid drops on a rough surface comprising microgrooves[J]. Experiments in Fluids, 2008, 44(6):927-938.
[9]	PEARSON J T, MAYNES D, WEBB B W. Droplet impact dynamics for two liquids impinging on anisotropic superhydrophobic surface[J]. Experiments in Fluids, 2012, 53(3):603-618.
[10]	林林, 袁儒强, 张欣欣, 等. 液滴在梯度微结构表面上的铺展动力学分析[J]. 物理学报, 2015, 64(15):154705. LIN L, YUAN R Q, ZHANG X X, et al. Spreading dynamics of liquid droplet on gradient micro-structured surfaces[J]. Acta Phys. Sin., 2015, 64(15):154705.
[11]	罗黎明, 贾志海. 液滴撞击高温梯度表面的动态行为特性[J]. 化工进展, 2018, 37(3):906-912. LUO L M, JIA Z H. Dynamic behavior of droplets impact on a hot microstructured surface with wetting gradient[J]. Chemical Industry and Engineering Progress, 2018, 37(3):906-912.
[12]	LIU Y, WHYMAN G, BORMASHENKO E, et al. Controlling drop bouncing using surfaces with gradient features[J]. Applied Physics Letters, 2015, 107(5):051604.
[13]	TANGUY S, BERLEMONT A. Application of a level set method for simulation of droplet collisions[J]. International Journal of Multiphase Flow, 2005, 31(9):1015-1035.
[14]	SANG H L, HUR N, KANG S. A numerical analysis of drop impact on liquid film by using a level set method[J]. Journal of Mechanical Science and Technology, 2011, 25(10):2567-2572.
[15]	NIKOLOPOULOS N, THEODORAKAKOS A, BERGELES G. A numerical investigation of the evaporation process of a liquid droplet impinging onto a hot substrate[J]. International Journal of Heat and Mass Transfer, 2007, 50(1/2):303-319.
[16]	梁超, 王宏, 朱恂, 等. 液滴撞击不同浸润性壁面动态过程的数值模拟[J]. 化工学报, 2013, 64(8):2745-2751. LIANG C, WANG H, ZHU X, et al. Numerical simulation of droplet impact on surface with different wettabilities[J]. CIESC Journal, 2013, 64(8):2745-2751.
[17]	LUNKAD S F, BUWA V V, NIGAM K D P. Numerical simulations of drop impact and spreading on horizontal and inclined surfaces[J]. Chemical Engineering Science, 2007, 62(24):7214-7224.
[18]	HIRT C W, NICHOLS B D. Volume of fluid (VOF) method for the dynamics of free boundaries[J]. Journal of Computational Physics, 1981, 39(1):201-225.
[19]	OSHER S, SETHIAN J A. Fronts propagating with curvature-dependent speed:algorithms based on Hamilton-Jacobi formulations[J]. Journal of Computational Physics, 1988, 79(1):12-49.
[20]	SUSSMAN M, PUCKETT E G. A coupled level set and volume-of-fluid method for computing 3D and axisymmetric incompressible two-phase flows[J]. Journal of Computational Physics, 2000, 162(2):301-307.
[21]	BRACKBILL J U, KOTHE D B, ZEMACH C. A continuum method for modeling surface tension[J]. Journal of Computational Physics, 1992, 100(2):335-354.
[22]	LI D, ZHANG D, ZHENG Z, et al. Numerical analysis on air entrapment during a droplet impacts on a dry flat surface[J]. International Journal of Heat and Mass Transfer, 2017, 115:186-193.
[23]	LI D, DUAN X, ZHENG Z, et al. Dynamics and heat transfer of a hollow droplet impact on a wetted solid surface[J]. International Journal of Heat and Mass Transfer, 2018, 122:1014-1023.
[24]	梁刚涛, 郭亚丽, 沈胜强. 液滴撞击液膜的射流与水花形成机理分析[J]. 物理学报, 2013, 62(2):024705. LIANG G T, GUO Y L, SHEN S Q. Analysis of liquid sheet and jet flow mechanism after droplet impinging onto liquid film[J]. Acta Phys. Sin., 2013, 62(2):024705.
[25]	SHEN S, BI F, GUO Y. Simulation of droplets impact on curved surfaces with lattice Boltzmann method[J]. International Journal of Heat and Mass Transfer, 2012, 55(23/24):6938-6943.
[26]	郑志伟, 李大树, 仇性启, 等. 液滴碰撞球形凹曲面复合level set-VOF法的数值分析[J]. 化工学报, 2015, 66(5):1667-1675. ZHENG Z W, LI D S, QIU X Q, et al. Numerical analysis of coupled level set-VOF method on droplet impact on spherical concave surface[J]. CIESC Journal, 2015, 66(5):1667-1675.
[27]	KUMAR A, GU S, TABBARA H, et al. Study of impingement of hollow ZrO2, droplets onto a substrate[J]. Surface and Coatings Technology, 2013, 220(15):164-169.
[28]	LEE J S, WEON B M, JE J H, et al. How does an air film evolve into a bubble during drop impact?[J]. Physical Review Letters, 2012, 109(20):204501.
[29]	LIU Y, TAN P, XU L. Compressible air entrapment in high-speed drop impacts on solid surfaces[J]. Journal of Fluid Mechanics, 2013, 716(2):R9.
[30]	LI E Q, THORODDSEN S T. Time-resolved imaging of a compressible air-disc under a drop impacting on a solid surface[J]. Journal of Fluid Mechanics, 2015, 780:636-648.

含气泡油滴撞击矩形沟槽壁面的数值分析

Numerical analysis of hollow oil droplet impact on rectangular groove surface

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献 30

相关文章 15

编辑推荐

Metrics

本文评价

[1]	宋嘉豪, 王文. 斯特林发动机与高温热管耦合运行特性研究[J]. 化工学报, 2023, 74(S1): 287-294.
[2]	张思雨, 殷勇高, 贾鹏琦, 叶威. 双U型地埋管群跨季节蓄热特性研究[J]. 化工学报, 2023, 74(S1): 295-301.
[3]	金正浩, 封立杰, 李舒宏. 氨水溶液交叉型再吸收式热泵的能量及分析[J]. 化工学报, 2023, 74(S1): 53-63.
[4]	程成, 段钟弟, 孙浩然, 胡海涛, 薛鸿祥. 表面微结构对析晶沉积特性影响的格子Boltzmann模拟[J]. 化工学报, 2023, 74(S1): 74-86.
[5]	肖明堃, 杨光, 黄永华, 吴静怡. 浸没孔液氧气泡动力学数值研究[J]. 化工学报, 2023, 74(S1): 87-95.
[6]	叶展羽, 山訸, 徐震原. 用于太阳能蒸发的折纸式蒸发器性能仿真[J]. 化工学报, 2023, 74(S1): 132-140.
[7]	邵苛苛, 宋孟杰, 江正勇, 张旋, 张龙, 高润淼, 甄泽康. 水平方向上冰中受陷气泡形成和分布实验研究[J]. 化工学报, 2023, 74(S1): 161-164.
[8]	毕丽森, 刘斌, 胡恒祥, 曾涛, 李卓睿, 宋健飞, 吴翰铭. 粗糙界面上纳米液滴蒸发模式的分子动力学研究[J]. 化工学报, 2023, 74(S1): 172-178.
[9]	张义飞, 刘舫辰, 张双星, 杜文静. 超临界二氧化碳用印刷电路板式换热器性能分析[J]. 化工学报, 2023, 74(S1): 183-190.
[10]	王志国, 薛孟, 董芋双, 张田震, 秦晓凯, 韩强. 基于裂隙粗糙性表征方法的地热岩体热流耦合数值模拟与分析[J]. 化工学报, 2023, 74(S1): 223-234.
[11]	于宏鑫, 邵双全. 水结晶过程的分子动力学模拟分析[J]. 化工学报, 2023, 74(S1): 250-258.
[12]	范孝雄, 郝丽芳, 范垂钢, 李松庚. LaMnO₃/生物炭催化剂低温NH₃-SCR催化脱硝性能研究[J]. 化工学报, 2023, 74(9): 3821-3830.
[13]	何松, 刘乔迈, 谢广烁, 王斯民, 肖娟. 高浓度水煤浆管道气膜减阻两相流模拟及代理辅助优化[J]. 化工学报, 2023, 74(9): 3766-3774.
[14]	郑佳丽, 李志会, 赵新强, 王延吉. 离子液体催化合成2-氰基呋喃反应动力学研究[J]. 化工学报, 2023, 74(9): 3708-3715.
[15]	袁佳琦, 刘政, 黄锐, 张乐福, 贺登辉. 泡状入流条件下旋流泵能量转换特性研究[J]. 化工学报, 2023, 74(9): 3807-3820.