化工学报 ›› 2014, Vol. 65 ›› Issue (8): 3261-3267.DOI: 10.3969/j.issn.0438-1157.2014.08.056

• 材料化学工程与纳米技术 • 上一篇    下一篇

ARGET ATRP法合成聚氯乙烯接枝丙烯酸丁酯共聚物

刘克勇, 包永忠   

  1. 浙江大学化学工程与生物工程学系, 化学工程联合国家重点实验室, 浙江 杭州 310027
  • 收稿日期:2013-11-08 修回日期:2014-01-25 出版日期:2014-08-05 发布日期:2014-08-05
  • 通讯作者: 包永忠

Synthesis of poly(vinyl chloride)-butyl acrylate graft copolymer by ARGET ATRP method

LIU Keyong, BAO Yongzhong   

  1. State Key Laboratory of Chemical Engineering, Department of Chemical and Biological Engineering, Zhejiang University, Hangzhou 310027, Zhejiang, Cina
  • Received:2013-11-08 Revised:2014-01-25 Online:2014-08-05 Published:2014-08-05

摘要: 以不稳定氯含量高的聚氯乙烯(U-PVC)和氯乙烯-溴代异丁酸烯丙酯共聚物(PVC-co-ABrMP)为大分子引发剂,使用电子转移催化再生原子转移自由基聚合(ARGET ATRP)进行丙烯酸丁酯(BA)的溶液接枝共聚。在固定CuCl2:三(2-吡啶甲基)胺:辛酸亚锡(摩尔比)时,当CuCl2用量(相对于氯乙烯链节数)小于0.1%时,BA转化率随CuCl2用量增加而明显增加;辛酸亚锡与CuCl2摩尔比大于50时,辛酸亚锡用量对聚合速率的影响较小;相同催化体系用量下,采用PVC-co-ABrMP为引发剂,可获得更高的BA转化率。通过PVC-co-ABrMP酯基水解得到PBA支链,其分子量分布指数为1.29,符合“活性”自由基聚合的特征。接枝PBA对PVC有明显的内增塑效果,PBA摩尔分数为32.75%的PVC-g-BA的玻璃化温度为8.34℃。

关键词: 聚合, 反应动力学, 催化剂, 聚氯乙烯, 丙烯酸丁酯, 接枝

Abstract: The grafting copolymerization of butyl acrylate (BA) onto poly(vinyl chloride) (PVC) was conducted through the method of activators regenerated by electron transfer atom transfer radical polymerization (ARGET ATRP), using PVC with higher labile chlorine content (U-PVC) and vinyl chloride/allyl 2-bromo-2-methylpropionate random copolymer (PVC-co-ABrMP) as an initiator. The polymerization conversion of BA was obviously increased as CuCl2 concentration (based on number of vinyl chloride unit) increased when CuCl2 concentration was lower than 0.1%. The increase of BA polymerization rate was not obvious when Sn(EH)2/CuCl2 molar ratio exceeded 50. The greater BA polymerization rate and PBA grafting degree were achieved when PVC-co-ABrMP was used as the initiator with the same catalyst. The side PBA chains were cleaved from the ester group of PVC-co-ABrMP and the molecular weight distribution index of PBA was 1.29, verifying the “living” nature of this graft copolymerization. The grafted PBA showed good internal plasticization effect on PVC, and the glass temperature of PVC-g-BA copolymer with 32.75%(mol) PBA was reduced to 8.34℃.

Key words: polymerization, reaction kinetics, catalyst, poly(vinyl chloride), butyl acrylate, grafting

中图分类号: