洗涤冷却环内液体冷态流动行为数值模拟

doi:10.3969/j.issn.0438-1157.2014.08.011

化工学报 ›› 2014, Vol. 65 ›› Issue (8): 2927-2933.DOI: 10.3969/j.issn.0438-1157.2014.08.011

洗涤冷却环内液体冷态流动行为数值模拟

颜留成, 王亦飞, 王灵萍, 潘飞, 郭强强, 于广锁

煤气化及能源化工教育部重点实验室, 华东理工大学洁净煤技术研究所, 上海 200237

收稿日期:2013-09-26 修回日期:2013-12-31 出版日期:2014-08-05 发布日期:2014-08-05
通讯作者: 王亦飞
基金资助:
国家重点基础研究发展计划项目（2010CB22700）。

Numerical simulation of cold state liquid flow in scrubbing-cooling ring

YAN Liucheng, WAN Yifei, WANG Lingping, PAN Fei, GUO Qiangqiang, YU Guangsuo

Key Laboratory of Coal Gasification and Energy Chemical Engineering of Ministry of Education, Institute of Clean Coal Technology, East China University of Science and Technology, Shanghai 200237, China

Received:2013-09-26 Revised:2013-12-31 Online:2014-08-05 Published:2014-08-05
Supported by:
supported by the National Basic Research Program of China (2010CB22700).

摘要/Abstract

摘要： 为了研究洗涤冷却环内冷却水流动的情况，借助计算流体力学软件Fluent建立了洗涤冷却环流体冷态流动的数学模型，同时为了验证模型的可靠性，对洗涤冷却环出口处的流动情况进行了实验研究，实验结果与模拟结果基本吻合。结果表明：因为洗涤冷却环的结构限制，其内部存在多处涡旋区域；内室入水口周向位置处的涡旋运动最为剧烈；受其影响，入水口周向位置的射流孔出口平均速度最小，两入水口之间周向位置的射流孔出口平均流速最大；槽缝出口的平均流速在周向上的分布与射流孔出口平均流速分布相同。

关键词: 计算流体力学, 数值模拟, 湍流, 洗涤冷却环, 速度分布

Abstract: In order to investigate the flow behavior of cooling water in scrubbing-cooling ring, especially at the outlet of the ring, a mathematical model for the fluid flow in scrubbing-cooling ring was established with Fluent, a software of computational fluid dynamics. The experimental study was carried out to measure the average velocity at the outlet of scrubbing-cooling ring to verify the mathematical model. The velocity of jet hole and slot was obtained from experiment and simulation. The numerical simulation result fits the experimental result well. It suggests that vortex exists inside the scrubbing-cooling ring because of the structure of the ring. The motion of vortex is most violent along the circumference of inlet in the inner chamber, so that the average outlet velocity of jet hole at the circumference of inlet is the minimum and the velocity at the circumferential position between two inlets is the maximum. The distribution of average outlet velocity of slot at circumferential position is the same with that of jet hole.

Key words: CFD, numerical simulation, turbulent flow, scrubbing-cooling ring, velocity distribution

中图分类号:

TQ021

颜留成, 王亦飞, 王灵萍, 潘飞, 郭强强, 于广锁. 洗涤冷却环内液体冷态流动行为数值模拟[J]. 化工学报, 2014, 65(8): 2927-2933.

YAN Liucheng, WAN Yifei, WANG Lingping, PAN Fei, GUO Qiangqiang, YU Guangsuo. Numerical simulation of cold state liquid flow in scrubbing-cooling ring[J]. CIESC Journal, 2014, 65(8): 2927-2933.

参考文献 21

[1]	Wang Fuchen (王辅臣), Yu Guangsuo (于广锁), Gong Xin (龚欣), Liu Haifeng (刘海峰), Wang Yifei (王亦飞), Liang Qinfeng (梁钦锋). Research and development of large-scale coal gasification technology[J]. Chemical Industry and Engineering Progress (化工进展), 2009, 28 (2): 173-180
[2]	Yu Zunhong (于遵宏), Wang Yifei (王亦飞), Zhou Zhijie (周志杰), Liu Haifeng (刘海峰), Gong Xin (龚欣), Yu Guangsuo (于广锁), Wang Fuchen (王辅臣), Liu Xiaojun (刘小军). A compound bed high temperature gas cooling and washing equipment and its industrial application [P]: CN, 01112880.1. 2001-11-12
[3]	Lu Ruihua (卢瑞华), Wang Yifei (王亦飞), Su Yifeng (苏宜丰), Wu Hongtao (吴宏涛), Li Wei (李伟), Yu Zunhong (于遵宏). Droplets statistics model for water entrainment in the separation zone of the compound bubbling chamber [J]. Chemical Reaction Engineering and Technology (化学反应工程与工艺), 2006, 22 (1): 37-42
[4]	Wang Yifei (王亦飞), Chen Yixin(陈意心), Liu Xia(刘霞), Liang Tie(梁铁), Yao Yongchun(姚永春), Yu Zunhong (于遵宏). Entraining liquid problem in a new type of scrubbing-cooling chamber [J]. Chemical Reaction Engineering and Technology (化学反应工程与工艺), 2008, 24 (1): 24-28
[5]	Wu Xuan (吴晅), Cai Jie (蔡杰), Li Tie (李铁), Yuan Zhulin (袁竹林). Numerical study of gravity separation of droplets in gas-liquid separation space of scrubbing-cooling chamber [J]. Journal of Southeast University: Natural Science Edition (东南大学学报: 自然科学版), 2008, 38 (6): 1017-1023
[6]	Lin Lan (林岚), Wang Yifei (王亦飞), Guo Qiangqiang (郭强强), Wang Fuchen (王辅臣). Effects of liquid properties on liquid entrainment in a new scrubbing-cooling chamber [J]. The Chinese Journal of Process Engineering (过程工程学报), 2011, 11 (5): 742-746
[7]	Wu Xuan (吴晅), Li Tie (李铁), Cai Jie (蔡杰), Yuan Zhulin (袁竹林). Study on simulating characteristics of gas-liquid flow in liquid cistern of the scrubbing-cooling chamber [J]. Thermal Power Generation (热力发电), 2008, 37 (5): 10-15
[8]	Wu Xuan (吴晅), Wu Wenfei (武文斐), Li Tie (李铁), Yuan Zhulin (袁竹林). Numerical simulation of influence of demarcation plates on gas-liquid two-phase flow characteristics in scrubbing-cooling chamber of gasifier [J]. Clean Coal Technology (洁净煤技术), 2012, 18 (3): 84-88
[9]	Li Tie (李铁), Li Weili (李伟力), Yuan Zhulin (袁竹林). Flowing characteristics of liquid film in vertical pipe [J]. Journal of Southeast University: Natural Science Edition (东南大学学报: 自然科学版), 2006, 36 (6): 962-966
[10]	Chen Yixin(陈意心), Wang Yifei(王亦飞), Liang Tie(梁铁), Yao Yongchun(姚永春), Liu Xia(刘霞), Yu Zunhong (于遵宏). Characteristic of phase distribution of gas-liquid two-phase flow in new scrubbing-cooling chamber [J]. Journal of Chemical Industry and Engineering (China) (化工学报), 2008, 59 (2): 322-327
[11]	Fu Bihua (付碧华), Wang Yifei (王亦飞), Lin Lan (林岚), Xu Jianliang (许建良), Wang Jian (王俭), Luo Chuntao (罗春桃), Wang Fuchen (王辅臣). Penetration depth and characteristics of interface fluctuation at quenching pipe outlet [J]. CIESC Journal (化工学报), 2011, 62 (7): 1817-1823
[12]	Meza C E, Balakotaiah V. Modeling and experimental studies of large amplitude waves on vertically falling films [J]. Chemical Engineering Science, 2008, 63 (19): 4704-4734
[13]	Wang Lingping (王灵萍), Wang Yifei (王亦飞), Guo Qiangqiang (郭强强), Yan Liucheng (颜留成), Yu Guangsuo (于广锁). Flow characteristics of vertical falling film in scrubbing-cooling pipe [J]. CIESC Journal (化工学报), 2013, 64 (6): 1959-1968
[14]	Li Yun (李云), Gu Zhaolin (顾兆林), Yu Yongzhang (郁永章), Feng Xiao (冯霄), Wang Hongjin (王洪金), He Zuwei (贺祖蔚), Tang Yingjie (唐应杰). Simulation of heat and mass transfer process in vertical pipe in quench chamber of TEXACO gasifier [J]. Chemical Engineering (China) (化学工程), 2000, 28 (4): 22-24
[15]	Liu Xia (刘霞), Wang Yifei (王亦飞), Zhao Xiaohui (赵晓辉), Gong Xin (龚欣), Yu Zunhong (于遵宏). Experimental study and numerical simulation of heat and mass transfer in scrubbing-cooling pipe [J]. Chemical Engineering (China) (化学工程), 2009, 37 (6): 12-15
[16]	Li Tie (李铁), Li Weili (李伟力), Yuan Zhulin (袁竹林). Different radiative models for heat and mass transfer characteristics in vertical pipe [J]. Proceedings of the CSEE (中国电机工程学报), 2007, 27 (2): 92-98
[17]	Li Tie (李铁), Wu Xuan (吴晅), Yuan Zhulin (袁竹林). Numercial research on gas-solid two-phase flow and heat transfer in cooling pipe coal-water-slurry of gasifier [J]. Proceedings of the CSEE (中国电机工程学报), 2010, 30 (14): 77-82
[18]	Wang Yifei (王亦飞), Wu Hongtao (吴宏涛), He Biyun (贺必云), Lu Ruihua (卢瑞华), Yu Zunhong (于遵宏). Development of a new rotary falling film quench ring for scrubbing and cooling hit syngas [J]. Journal of East China University of Science and Technology (华东理工大学学报), 2005, 31 (6): 752-755
[19]	Xu Ming (徐明), Zhang Zhongxiao (张忠孝), Fan Junjie (樊俊杰), Lou Tong (娄彤). Numerical simulation of cold flow field in quench ring of entrained-bed gasifier [J]. Clean Coal Technology (洁净煤技术), 2012, 18 (1): 75-94
[20]	Dai Gance (戴干策), Chen Minheng (陈敏恒). Chemical Engineering Hydrodynamics (化工流体力学) [M]. 2nd ed. Beijing: Chemical Industry Press, 2005: 77
[21]	Li Jinliang (李进良), Li Chengxi (李承曦), Hu Renxi (胡仁喜). Proficient in Flow Field Analysis of FLUENT 6.3 (精通FLUENT6.3流场分析) [M]. Beijing: Chemical Industry Press, 2009: 44

洗涤冷却环内液体冷态流动行为数值模拟

Numerical simulation of cold state liquid flow in scrubbing-cooling ring

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献 21

相关文章 15

编辑推荐

Metrics

本文评价

[1]	叶展羽, 山訸, 徐震原. 用于太阳能蒸发的折纸式蒸发器性能仿真[J]. 化工学报, 2023, 74(S1): 132-140.
[2]	张义飞, 刘舫辰, 张双星, 杜文静. 超临界二氧化碳用印刷电路板式换热器性能分析[J]. 化工学报, 2023, 74(S1): 183-190.
[3]	王志国, 薛孟, 董芋双, 张田震, 秦晓凯, 韩强. 基于裂隙粗糙性表征方法的地热岩体热流耦合数值模拟与分析[J]. 化工学报, 2023, 74(S1): 223-234.
[4]	宋嘉豪, 王文. 斯特林发动机与高温热管耦合运行特性研究[J]. 化工学报, 2023, 74(S1): 287-294.
[5]	张思雨, 殷勇高, 贾鹏琦, 叶威. 双U型地埋管群跨季节蓄热特性研究[J]. 化工学报, 2023, 74(S1): 295-301.
[6]	肖明堃, 杨光, 黄永华, 吴静怡. 浸没孔液氧气泡动力学数值研究[J]. 化工学报, 2023, 74(S1): 87-95.
[7]	温凯杰, 郭力, 夏诏杰, 陈建华. 一种耦合CFD与深度学习的气固快速模拟方法[J]. 化工学报, 2023, 74(9): 3775-3785.
[8]	何松, 刘乔迈, 谢广烁, 王斯民, 肖娟. 高浓度水煤浆管道气膜减阻两相流模拟及代理辅助优化[J]. 化工学报, 2023, 74(9): 3766-3774.
[9]	邢雷, 苗春雨, 蒋明虎, 赵立新, 李新亚. 井下微型气液旋流分离器优化设计与性能分析[J]. 化工学报, 2023, 74(8): 3394-3406.
[10]	汪林正, 陆俞冰, 张睿智, 罗永浩. 基于分子动力学模拟的VOCs热氧化特性分析[J]. 化工学报, 2023, 74(8): 3242-3255.
[11]	程小松, 殷勇高, 车春文. 不同工质在溶液除湿真空再生系统中的性能对比[J]. 化工学报, 2023, 74(8): 3494-3501.
[12]	刘文竹, 云和明, 王宝雪, 胡明哲, 仲崇龙. 基于场协同和耗散的微通道拓扑优化研究[J]. 化工学报, 2023, 74(8): 3329-3341.
[13]	洪瑞, 袁宝强, 杜文静. 垂直上升管内超临界二氧化碳传热恶化机理分析[J]. 化工学报, 2023, 74(8): 3309-3319.
[14]	岳林静, 廖艺涵, 薛源, 李雪洁, 李玉星, 刘翠伟. 凹坑缺陷对厚孔板喉部空化流动特性影响研究[J]. 化工学报, 2023, 74(8): 3292-3308.
[15]	韩晨, 司徒友珉, 朱斌, 许建良, 郭晓镭, 刘海峰. 协同处理废液的多喷嘴粉煤气化炉内反应流动研究[J]. 化工学报, 2023, 74(8): 3266-3278.