低温预制钛系催化剂合成cis-1,4-聚异戊二烯

doi:10.11949/j.issn.0438-1157.20150032

化工学报 ›› 2015, Vol. 66 ›› Issue (7): 2521-2527.DOI: 10.11949/j.issn.0438-1157.20150032

• 催化、动力学与反应器 • 上一篇下一篇

低温预制钛系催化剂合成cis-1,4-聚异戊二烯

汪昭玮^1,2, 于俊伟³, 李兴², 刘晓暄¹

1 广东工业大学材料与能源学院高分子材料与工程系, 广东广州 510006;
2 中国广州分析测试中心, 广东省分析测试技术公共实验室, 广东广州 510070;
3 茂名鲁华化工有限公司, 广东茂名 525000

收稿日期:2015-01-09 修回日期:2015-04-27 出版日期:2015-07-05 发布日期:2015-07-05
通讯作者: 刘晓暄
基金资助:
省部产学研合作重大专项(入库)鲁华分项(2012A090300006)。

Synthesis of cis-1,4-polyisoprene with low-temperature prepared Ti-Al catalysts

WANG Zhaowei^1,2, YU Junwei³, LI Xing², LIU Xiaoxuan¹

1 Department of Polymeric Materials and Engineering, School of Materials and Energy, Guangdong University of Technology, Guangzhou 510006, Guangdong, China;
2 Guangdong Provincial Public Laboratory of Analysis and Testing Technology, China National Analytical Center, Guangzhou 510070, Guangdong, China;
3 Maoming Luhua Chemical Engineering Ltd. Co., Maoming 525000, Guangdong, China

Received:2015-01-09 Revised:2015-04-27 Online:2015-07-05 Published:2015-07-05

摘要/Abstract

摘要：

采用Ziegler-Natta配位聚合制备了高顺式聚异戊二烯,主要考察了非均相催化体系四氯化钛-三异丁基铝二组分催化剂的预制方法以及催化剂预制条件对异戊二烯体系聚合规律的影响。讨论了催化剂配比、预制催化剂温度和陈化温度对催化剂活性及聚合物的凝胶含量、特征黏度、微观结构含量等方面的影响。同时讨论了催化剂用量、聚合温度和聚合时间对聚合活性及聚合物的凝胶含量、特征黏度、微观含量等方面的影响。研究结果表明,合成高cis-1,4-聚异戊二烯的最佳实验条件为:Al/Ti摩尔比1.0,催化剂预制温度-40℃,陈化2 h,Ti/Ip摩尔比6×10^-3,聚合温度50℃,聚合时间5 h。所得聚合物最高转化率为87.1%,cis-1,4结构含量为91.76%。

关键词: 催化剂, 配位聚合, cis-1,4-聚异戊二烯, 低温, 多相反应, 活性

Abstract:

The high cis-1,4-polyisoprene is prepared by Ziegler-Natta coordination polymerization. The effect of preparation method and condition of heterogeneous TiCl₄-Al(i-Bu)₃ two component catalyst on isoprene polymerization are investigated. The influence of several parameters on the catalytic activity, the gel content, intrinsic viscosity, microstructure and cis-1,4-content of the polyisoprene is examined in detail, including mole ratio of catalyst component, prefabricate temperature and aging time as well as catalyst dosage, polymerization temperature and time. The results show that the optimum conditions of catalyst preparation are as follows: the molar ratio of Al/Ti is 1.0, the temperature of prefabricate is at -40℃, the aging time is 2 h at room temperature, molar ratio of Ti/Ip(catalyst content)is 6×10^-3, the polymerization for 5 h at 50℃. Under these condition, the monomer conversion is 87.1% in the polymerization, the microstructure cis-1,4 content in obtained polymer is up to 91.76%.

Key words: catalyst, Ziegler-Natta polymerization, cis-1,4-polyisoprene, low-temperature, multiphase reaction, reactivity

中图分类号:

TQ333.3

汪昭玮, 于俊伟, 李兴, 刘晓暄. 低温预制钛系催化剂合成cis-1,4-聚异戊二烯[J]. 化工学报, 2015, 66(7): 2521-2527.

WANG Zhaowei, YU Junwei, LI Xing, LIU Xiaoxuan. Synthesis of cis-1,4-polyisoprene with low-temperature prepared Ti-Al catalysts[J]. CIESC Journal, 2015, 66(7): 2521-2527.

参考文献 19

[1]	Cao Jianming(曹建明), Ren Meihong(任美红), Zhao Yuzhong(赵玉中). Development situation and proposal on isoprene rubber at home and abroad [J]. New Chemical Materials(化工新型材料), 2007, 35(5): 84-86.
[2]	Qian Bozhang(钱伯章). Current situation and development outlook of IR market in China [J]. China Rubber(中国橡胶), 2006, 22(23): 26-28.
[3]	Li Jinling(李金玲), Li Shufeng(李树丰), Dong Changhe(董长河), Wan Xiaojun(万晓军). Production status & market analysis of epoxy resin at home and abroad [J]. China Elastomerics(弹性体), 2012, 22(5): 80-83.
[4]	Huang Yuan(黄源), Cao Kun(曹堃), Li Baofang (李宝芳), Li Bogeng(李伯耿). Kinetics of bulk graft copolymerization of styrene onto rubber [J]. Journal of Chemical Industry and Engineering(China) (化工学报), 2004, 55(6):985-990.
[5]	Sun Yuxiao(孙欲晓), Li Jiangli(李江利), Guo Binshi(郭滨诗), Fei Jiaming(费家明), Wei Jingjiang(魏井江), Dong Wu(董武). Current situation and development proposal on isoprene rubber at home and abroad [J]. China Elastomerics(弹性体), 2009, 19(6): 60-64.
[6]	Adams H E, Stearns R S, Smith W A. cis-1, 4-Polyisoprene prepared with alkyl aluminum and titanium tetrachloride [J]. Rubber Chemistry and Technology, 1958, 31(4): 838-846.
[7]	Saltman W M, Link T H. Catalytic species in some alkyl aluminum titanium iodide catalysts for cis-1, 4-polybutadiene [J]. Industrial & Engineering Chemistry Product Research and Development, 1964, 3(3): 199-203.
[8]	Schoenberg E, Chalfant D L, Mayor R H. Preformed aluminum triisobutyl-titanium tetrachloride catalysts for isoprene polymerization [J]. Rubber Chemistry and Technology, 1964, 37(1): 103-120.
[9]	Castner, Kenneth Floyd. Synthesis of cis-1,4-polyisoprene rubber[P]: US, 5919876. 1999-07-06.
[10]	Wang Peng(王鹏), Xu Zhaolai(徐召来), Shao Huafeng(邵华锋), Yao Wei(姚薇), Huang Baochen(黄宝琛). Polymerization of isoprene catalyzed by titanates-TiCl4/MgCl2 and AlEt3 [J]. Journal of Qingdao University of Science and Technology: Natural Science Edition (青岛科技大学学报:自然科学版), 2010, (1): 61-66.
[11]	Huang Baochen(黄宝琛), He Jidong(贺继东), Xu Ling(徐玲), Zhou Jiansong(周健松), Cai Ming(蔡明), Tang Xueming(唐学明). Study on synthesis of trans-1,4-polyisoprene with supported titanium catalyst [J]. Journal of Qingdao University of Science and Technology: Natural Science Edition (青岛化工学院学报:自然科学版), 1990, (4): 1-8.
[12]	Yu Tao(于涛), Gao Rong(高榕), Yao Wei(姚薇), Zhao Yongxian(赵永仙), Huang Baochen(黄宝琛). Polymerization of isoprene with supported titanium catalyst modified by n-octanol [J]. China Elastomerics(弹性体), 2005, 15(4): 38-42
[13]	Bi Lei(毕磊), Zhang Hexia(张合霞), Wang Tao(王涛), Qu Henghui(曲恒辉), Yao Wei(姚薇), Huang Baochen(黄宝琛). Polymerization of isoprene with supported TiCl3(OC4H9) catalysts [J]. Chemical Propellants & Polymeric Materials(化学推进剂与高分子材料), 2007, 5(2): 60-61.
[14]	Wang Peng(王鹏), Shao Huafeng(邵华锋), Yao Wei(姚薇), Huang Baochen(黄宝琛). Polymerization of isoprene initiated with tetra-n-butyl titanate, supported titanium catalyst and triethylaluminium (Ⅰ): Effect of polymerization conditions [J]. China Synthetic Rubber Industry(合成橡胶工业), 2009, 32(4): 284-289.
[15]	Zhu Han(朱寒), Bai Zhixin(白志欣), Zhao Jiangwei(赵姜维), Ling Ping(零萍), Wu Yixuan(吴一弦). Synthesis of polyisoprene with high cis-1,4-content and narrow molecular weight distribution and polymerization kinetics [J]. Acta Polymerica Sinica(高分子学报), 2012, (5): 571-579.
[16]	Hu Jing(胡婧), Bo Lin(柏林), Liu Qinghua(刘庆华), Shao Huafeng(邵华锋), Yao Wei(姚薇), Huang Baochen(黄宝琛). Polymerizaton of isoprene in the presence of supported titanium catalyst and Al(Et)3 [J]. China Elastomerics(弹性体), 2010, 20(1): 30-33.
[17]	Xu Shaolai(徐召来), Shao Fenghua(邵华锋), Yao Wei(姚薇), Huang Baochen(黄宝琛). Synthesis of trans-1,4-polyisoprene/3,4- polyisoprene compounded rubber with two-component titanium- based catalysts [J]. China Synthetic Rubber Industry(合成橡胶工业), 2010, 33(6): 418-423.
[18]	He A, Huang B, Jiao S. Synthesis of a high trans-1,4-butadiene/ isoprene copolymers with supported titanium catalysts [J]. Journal of Applied Polymer Science, 2003, 89(7): 1800-18
[19]	Jin Yingtai(金鹰泰), Sun Yufen(孙玉芬), Liu Xiaoxuan(刘晓暄), Li Xingmin(李兴民), Ouyang Jun(欧阳钧). Investigation on polymerization of conjugated dienes with the homogeneous rare earth catalyst [J]. Journal of Molecular Science(分子科学学报), 1984, (2): 247-252.

低温预制钛系催化剂合成cis-1,4-聚异戊二烯

Synthesis of cis-1,4-polyisoprene with low-temperature prepared Ti-Al catalysts

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献 19

相关文章 15

编辑推荐

Metrics

本文评价

[1]	杨学金, 杨金涛, 宁平, 王访, 宋晓双, 贾丽娟, 冯嘉予. 剧毒气体PH₃的干法净化技术研究进展[J]. 化工学报, 2023, 74(9): 3742-3755.
[2]	李艺彤, 郭航, 陈浩, 叶芳. 催化剂非均匀分布的质子交换膜燃料电池操作条件研究[J]. 化工学报, 2023, 74(9): 3831-3840.
[3]	陈杰, 林永胜, 肖恺, 杨臣, 邱挺. 胆碱基碱性离子液体催化合成仲丁醇性能研究[J]. 化工学报, 2023, 74(9): 3716-3730.
[4]	杨菲菲, 赵世熙, 周维, 倪中海. Sn掺杂的In₂O₃催化CO₂选择性加氢制甲醇[J]. 化工学报, 2023, 74(8): 3366-3374.
[5]	李凯旋, 谭伟, 张曼玉, 徐志豪, 王旭裕, 纪红兵. 富含零价钴活性位点的钴氮碳/活性炭设计及甲醛催化氧化应用研究[J]. 化工学报, 2023, 74(8): 3342-3352.
[6]	杨欣, 彭啸, 薛凯茹, 苏梦威, 吴燕. 分子印迹-TiO₂光电催化降解增溶PHE废水性能研究[J]. 化工学报, 2023, 74(8): 3564-3571.
[7]	吕龙义, 及文博, 韩沐达, 李伟光, 高文芳, 刘晓阳, 孙丽, 王鹏飞, 任芝军, 张光明. 铁基导电材料强化厌氧去除卤代有机污染物：研究进展及未来展望[J]. 化工学报, 2023, 74(8): 3193-3202.
[8]	余娅洁, 李静茹, 周树锋, 李清彪, 詹国武. 基于天然生物模板构建纳米材料及集成催化剂研究进展[J]. 化工学报, 2023, 74(7): 2735-2752.
[9]	屈园浩, 邓文义, 谢晓丹, 苏亚欣. 活性炭/石墨辅助污泥电渗脱水研究[J]. 化工学报, 2023, 74(7): 3038-3050.
[10]	王杰, 丘晓琳, 赵烨, 刘鑫洋, 韩忠强, 许雍, 蒋文瀚. 聚电解质静电沉积改性PHBV抗氧化膜的制备与性能研究[J]. 化工学报, 2023, 74(7): 3068-3078.
[11]	李盼, 马俊洋, 陈志豪, 王丽, 郭耘. Ru/α-MnO₂催化剂形貌对NH₃-SCO反应性能的影响[J]. 化工学报, 2023, 74(7): 2908-2918.
[12]	涂玉明, 邵高燕, 陈健杰, 刘凤, 田世超, 周智勇, 任钟旗. 钙基催化剂的设计合成及应用研究进展[J]. 化工学报, 2023, 74(7): 2717-2734.
[13]	张琦钰, 高利军, 苏宇航, 马晓博, 王翊丞, 张亚婷, 胡超. 碳基催化材料在电化学还原二氧化碳中的研究进展[J]. 化工学报, 2023, 74(7): 2753-2772.
[14]	张谭, 刘光, 李晋平, 孙予罕. Ru基氮还原电催化剂性能调控策略[J]. 化工学报, 2023, 74(6): 2264-2280.
[15]	朱风, 陈凯琳, 黄小凤, 鲍银珠, 李文斌, 刘嘉鑫, 吴玮强, 高王伟. KOH改性电石渣脱除羰基硫的性能研究[J]. 化工学报, 2023, 74(6): 2668-2679.