双层配碳烧结过程的传热传质分析

doi:10.11949/j.issn.0438-1157.20161334

摘要/Abstract

摘要：

为了研究双层配碳下的铁矿石烧结过程及其节能效益，建立了铁矿石烧结过程的二维非稳态数学模型。模型基于多孔介质理论，考虑了烧结过程中的主要物理变化和化学反应，以烧结杯为求解对象，利用FLUENT软件及C语言自定义编程对烧结过程进行了数值模拟，并利用烧结杯实验数据对模型进行了验证。通过对常规均匀配碳和双层非均匀配碳烧结的传热传质过程进行仿真计算，分析了两种烧结方式下床层温度和物料熔化分数分布，并通过熔化分数对烧结矿成品率进行判定。研究结果表明：在不改变整个床层配碳量的条件下，相对于单层均匀配碳，双层配碳条件下热效率更高，床层温度和物料熔化分数沿料层高度分布更加均匀；上下层物料配碳分别为5%和3.4%且料层厚度相同时，烧结成品率提高10%；降低上层高配碳区料层厚度，即当上下层厚度比为5：9，配碳为5%和3.756%时，成品率能够进一步提高。

关键词: 烧结, 数值模拟, 传热传质, 分层配碳, 熔化分数, 成品率

Abstract:

In order to analyze two-layer sintering process and its energy-saving benefit, a two-dimensional unsteady mathematical model of iron ore sintering process, which considered major physical changes and chemical reactions was developed based on porous media theory. Employed with FLUENT software and C language programming via custom code, the sintering process was simulated and a sinter pot test was used to validate the model. Both conventional sintering process and two-layer sintering process were simulated. Distributions of temperature and melt fraction in sintering bed were analyzed. Results showed that heat efficiency became higher, temperature and melt fraction distributed more evenly in two-layer sintering when coke rate was kept the same as in one-layer sintering. Besides, the yield increased 10% when coke rates were 5% in the upper layer and 3.4% in the lower layer while two layers had the same heights. Reducing the height of the upper layer the yield of the sintering could be further increased when the height ratio of the upper and lower layer was 5:9 and coke rates were 5% and 3.756% respectively.

Key words: sintering, numerical simulation, heat and mass transfer, multi-load coke in charge, melting fraction, yield

中图分类号:

TF046

张斌, 周孑民, 李茂. 双层配碳烧结过程的传热传质分析[J]. 化工学报, 2017, 68(5): 1811-1822.

ZHANG Bin, ZHOU Jiemin, LI Mao. Analysis of heat and mass transfer in two-layer sintering process[J]. CIESC Journal, 2017, 68(5): 1811-1822.

参考文献 32

[1]	郜学. 中国烧结行业的发展现状和趋势分析[J]. 钢铁, 2008, 43(1): 88-91. GAO X. Development situation and trend analysis of sintering industry in China[J]. Iron and Steel, 2008, 43(1): 88-91.
[2]	MASAAKI N, KANJI T, YOSHIYUKI M. Ironmaking technology for the last 100 years: deployment to advanced technologies from introduction of technological know-how, and evolution to next-generation process[J]. ISIJ International, 2015, 55 (1): 7-35.
[3]	付菊英, 姜涛, 朱德庆. 烧结球团学[M]. 长沙: 中南工业大学出版社, 1996. FU J Y, JIANG T, ZHU D Q. Sintering and Pelletizing[M]. Changsha: Central South University of Technology Press, 1996.
[4]	白晨光, 谢皓, 邱贵宝, 等. 烧结料层中的蓄热模型[J]. 重庆大学学报, 2008, 31(9): 1002-1007. BAI C G, XIE H, QIU G B, et al. An accumulation heat model and its application in iron ore sintering[J]. Journal of Chongqing University, 2008, 31(9): 1002-1007.
[5]	黄柱成, 江源, 毛晓明, 等. 铁矿烧结中燃料合理分布研究[J]. 中南大学学报(自然科学版), 2006, 37(5): 884-890. HUANG Z C, JIANG Y, MAO X M, et al. Fuel appropriate distribution in iron ore sintering[J]. Journal of Central South University(Science and Technology), 2006, 37(5): 884-890.
[6]	李法社, 张小辉, 张家元, 等. 基于料层最高温度控制的铁矿烧结燃料合理分布[J]. 中南大学学报(自然科学版), 2015, 46(2): 386-393. LI F S, ZHANG X H, ZHANG J Y, et al. Fuel appropriate distribution based on the highest temperature control in iron ore sintering[J]. Journal of Central South University(Science and Technology), 2015, 46(2): 386-393.
[7]	NATH N K, MITRA K. Mathematical modeling and optimization of two-layer sintering process for quality and fuel efficiency using genetic algorithm[J]. Manufacturing Processes, 2005, 20(3): 335-349.
[8]	陈林根, 夏少军, 谢志辉, 等. 钢铁冶金过程动态数学模型的研究进展[J]. 热科学与技术, 2014, 13(2): 95-125. CHEN L G, XIA S J, XIE Z H, et al. Progress in study on dynamic mathematical modeling of iron and steel metallurgy processes[J]. Journal of Thermal Science and Technology, 2014, 13(2): 95-125.
[9]	YOUNG R W. Dynamic mathematical model of sintering process[J]. Ironmaking and Steelmaking, 1977, 4(6): 321-324.
[10]	CUMMING M J, THURLBY J A. Developments in modeling and simulation of iron ore sintering[J]. Ironmaking and Steelmaking, 1990, 17(4): 245-248.
[11]	YANG W, RYU C, CHOI S. Unsteady one-dimensional model for a bed combustion of solid fuels[J]. Proceedings of the Institution of Mechanical Engineers Part A—Journal of Power and Energy, 2004, 218(A8): 589-598.
[12]	ZHOU H, ZHAO J P, LOO C E, et al. Numerical modeling of the iron ore sintering process[J]. ISIJ International, 2012, 52(9): 1550-1558.
[13]	ZHOU H, ZHAO J P, LOO C E, et al. Model prediction of important bed and gas properties during iron ore sintering[J]. ISIJ International, 2012, 52(12): 2168-2176.
[14]	YANG W, RYU C, CHOI S. Combustion characteristics in an iron ore sintering bed-evaluation of fuel substitution[J]. Combustion and Flame, 2006, 145(3): 447-463.
[15]	刘斌, 冯妍卉, 姜泽毅, 等. 烧结床层的热质分析[J]. 化工学报, 2012, 63(5): 1344-1353. LIU B, FENG Y H, JIANG Z Y, et al. Heat and mass transfer in sintering process[J]. CIESC Journal, 2012, 63(5): 1344-1353.
[16]	凌忠钱, 周昊, 钱欣平, 等. 自由堆积多孔介质内预混燃烧火焰传播[J]. 化工学报, 2008, 59(2): 456-460. LING Z Q, ZHOU H, QIAN X P, et al. Propagation of premixed combustion wave of methane/air in packed bed[J]. Journal of Chemical Industry and Engineering(China), 2008, 59(2): 456-460.
[17]	ZHOU H, LIU Z H, CHENG M, et al. Effect of flame-front speed on the pisolite-ore sintering process[J]. Applied Thermal Engineering, 2015, 75(22): 307-314.
[18]	MASOUD P, MOHSEN D E, MASOUD P. The effects of kinetic parameters on combustion characteristics in a sintering bed[J]. Energy, 2014, 73 (6): 160-176.
[19]	RAMOS M V, KASAI E, KANO J, et al. Numerical simulation model of the iron ore sintering directly describing the agglomeration phenomenon of granules in the packed bed[J]. ISIJ International, 2000, 40(5): 448-484.
[20]	CASTROA J A, PEREIRAA J L, GUILHERMEA V S, et al. Model predictions of PCDD and PCDF emissions on the iron ore sintering process based on alternative gaseous fuels[J]. Journal of Materials Research and Technology, 2013, 2(4): 323-331.
[21]	PATISSON F, BELLOT J P, ABLIZER D. Study of moisture transfer during the strand sintering process[J]. Metallurgical Transactions, 1990, 21B: 37-47.
[22]	李菊香, 涂善东. 考虑局部非热平衡的流体层流横掠多孔介质中恒热流平板的传热分析[J]. 化工学报, 2010, 61(1): 448-451. LI J X, TU S D. Heat transfer of laminar flow over a plate embedded in porous medium with a constant heat flux under local non-equilibrium condition[J]. CIESC Journal, 2010, 61(1): 448-454.
[23]	ALAZMI B, VAFAI K. Analysis of fluid flow and heat transfer interfacial conditions between a porous medium and a fluid layer[J]. International Journal of Heat and Mass Transfer, 2001, 44(9): 1735-1749.
[24]	KIM S J, JANG S P. Effects of the Darcy number, the Prandtl number, and the Reynolds number on local thermal non-equilibrium[J]. International Journal of Heat and Mass Transfer, 2002, 45(19): 3885-3896.
[25]	李茂, 母玉同, 张家元, 等. 烧结环冷机分层布料的数值模拟与优化[J]. 中南大学学报(自然科学版), 2013, 44(3): 1228-1234. LI M, MU Y T, ZHANG J Y, et al. Numerical simulation and optimization of sinter cooler in multilayered burden distribution[J]. Journal of Central South University(Science and Technology), 2013, 44(3): 1228-1234.
[26]	THUNMAN H, LECKNER B. Ignition and propagation of a reaction front in cross-current bed combustion of wet biofuels[J]. Fuel, 2001, 80(4): 473-481
[27]	PATISSON F, BELLOT J P, ABLIZER D, et al. Mathematical modeling of iron ore sintering process[J]. Ironmaking and Steelmaking, 1991, 18(2): 89-95.
[28]	俞昌铭. 多孔材料传热传质及其数值分析[M]. 北京: 清华大学出版社, 2011: 16-31. YU C M. Numerical Analysis of Heat and Mass Transfer for Porous Materials[M]. Beijing: Tsinghua University Press, 2011: 16-31.
[29]	CASTRO J A, SASAKI Y, YAGI J. Three dimensional mathematical model of the iron ore sintering process based on multiphase theory[J]. Materials Research, 2012, 15(2): 848-858.
[30]	ZHAO J P, LOO C E, DUKINO R D. Modeling fuel combustion in iron ore sintering[J]. Combustion and Flame, 2015, 162(4): 1019-1034.
[31]	LOO C E, TAME N, PENNY G C. Effect of iron ore and sintering conditions on flame front properties[J]. ISIJ International, 2012, 52(6): 967-976.
[32]	CHENG Z L, YANG J, ZHOU L, et al. Sinter strength evaluation using process parameters under different conditions in iron ore sintering process[J]. Applied Thermal Engineering, 2016, 105(1): 894-904.