载体含量对NaNO3/硅藻土复合相变储热材料的性能影响规律

doi:10.11949/j.issn.0438-1157.20170733

摘要/Abstract

摘要：

采用混合烧结工艺，通过改变硅藻土载体材料的质量分数制备5种不同参数的NaNO₃/硅藻土复合相变储热材料（CPCM）样品，并对其进行抗压强度测试、热物性测试、能谱表征、微观形貌观察及热性能分析。当硅藻土质量分数从30%增加到35%和40%时，样品抗压强度随之增加，表现出脆性材料特征，当达到45%和50%时，则表现出塑性材料特征。硅藻土的加入和混合烧结处理对NaNO₃的相变几乎没有影响。样品的热导率随温度升高而降低，在同一温度条件下，样品热导率均随硅藻土质量分数的升高基本呈上升趋势，但从30%增加到35%时，热导率的增幅大于从35%增加到50%时热导率的增幅，前者约为后者的8倍。与NaNO₃相比，样品在常温-相变前温度段和相变结束-最高温度段的平均比热容随硅藻土质量分数变化均出现先下降后上升的变化。硅藻土质量分数为35%时，样品内部结构致密，NaNO₃充分均匀吸附于硅藻土的分离独立小单元中。硅藻土质量分数为35%时样品具有较好的抗压强度和储热效果。

关键词: 硅藻土, NaNO₃, 复合材料, 相变, 抗压强度, 热物性, 吸附

Abstract:

Five NaNO₃/diatomite composite phase change materials (CPCM) for thermal energy storage with different mass content of diatomite were prepared using the mixing and sintering method. Diatomite and NaNO₃ were employed as carrier material and phase change material respectively. The compressive strength, thermal properties, microscopic morphology, photoelectron spectroscopy and thermal analysis were carried out. The compressive strength of the CPCM was enhanced with the mass fraction of diatomite increasing from 30% to 35% and 40% and showed brittle characteristic. When the mass fraction of diatomite reached 45% and 50%, the NaNO₃/diatomite CPCM performed the paddy behavior. The DSC characterization results revealed that diatomite had little effect on the latent heat and phase-change temperature of NaNO₃. The obtained results of LFA tests showed that the thermal conductivity of the CPCM decreased with the increase of the temperature. At the given temperature, the thermal conductivity of the NaNO₃/diatomite CPCM showed upward trend with the mass fraction of diatomite increases. It was also observed that the enhancing rate of the thermal conductivity was eight times larger when increasing the mass fraction of diatomite increased from 30% to 35% compared with the mass fraction increasing from 35% to 50%. Compared with pure NaNO₃, with the diatomite mass fraction increasing from 30% to 50%, the average specific heat capacity of the NaNO₃/diatomite CPCM performed the upward and downward trend within the room temperature-phase transition and the end of the phase transition-the highest temperature range. The SEM and EDS results showed that the NaNO₃/diatomite CPCM have dense structure with NaNO₃ adsorbed uniformly inside the diatomite. The desirable compressive strength and thermal properties of the NaNO₃/diatomite CPCM can be achieved by optimizing the mass ratio of diatomite. The NaNO₃/diatomite CPCM with 35% (mass) diatomite behaved superior overall performance according to the work in this paper.

Key words: diatomite, NaNO₃, composites, phase change, compressive strength, thermophysical properties, adsorption

中图分类号:

TQ33
TK02

郑莉芳, 冷光辉, 聂彬剑, 姜竹, 丁玉龙. 载体含量对NaNO₃/硅藻土复合相变储热材料的性能影响规律[J]. 化工学报, 2017, 68(11): 4428-4436.

ZHENG Lifang, LENG Guanghui, NIE Binjian, JIANG Zhu, DING Yulong. Effects of carrier on characteristics of NaNO₃/diatomite composite phase change materials for thermal energy storage[J]. CIESC Journal, 2017, 68(11): 4428-4436.

参考文献 37

[1]	仵斯, 李廷贤, 闫霆, 等. 高性能定形复合相变储能材料的制备及热性能[J]. 化工学报, 2015, 66(12):5127-5134. WU S, LI T X, YAN T, et al. Preparation and thermal properties of high performance shape-stabilized phase change composites using stearic acid and expanded graphite[J]. CIESC Journal, 2015, 66(12):5127-5134.
[2]	SARLOS G, DAURIAT A. Energy, a challenge for humanity in the 21st century[C]//International Conference on Energy and the Environment. 2003, 1/2:1-11.
[3]	于欣, 胡晓峰, 黄占华. 有机/复合相变储能材料研究进展[J]. 功能材料, 2012, 43(Z1):16-21. YU X, HU X F, HUANG Z H. Research progress of organic/composite phase change energy storage materials[J]. Journal of Functional Materials, 2012, 43(Z1):16-21.
[4]	刘涛, 李月明, 王竹梅, 等. 无机盐/石英基复合相变储能材料多孔陶瓷基体的制备[J]. 硅酸盐通报, 2013, 32(12):2476-2489. LIU T, LI Y M, WANG Z M, et al. Preparation of porous ceramic matrix for inorganic salt/quartz composite phase change energy storage materials[J]. Bulletin of the Chinese Ceramic Society, 2013, 32(12):2476-2489.
[5]	PASUPATHY A, VELRAJ R, SEENIRAJ R V. Phase change material-based building architecture for thermal management in residential and commercial establishments[J]. Renewable & Sustainable Energy Reviews, 2008, 12(1):39-64.
[6]	FARID M M, KHUDHAIR A M, RAZACK S A K, et al. A review on phase change energy storage:materials and applications[J]. Energy Conversion & Management, 2004, 45(9/10):1597-1615.
[7]	邱美鸽, 唐炳涛, 张淑芬, 等. 异丙醇铝溶胶-凝胶掺杂的SiO2-Al2O3/PEG导热增强型定形相变储能材料[J]. 复合材料学报, 2013, 30(3):93-99. QIU M G, TANG B T, ZHANG S F, et al. Thermal conductivity enhanced SiO2-Al2O3/PEG form-stable phase change material based on the sol-gel doping of aluminum isopropanol[J]. Acta Materiae Compositae Sinica, 2013, 30(3):93-99.
[8]	SILAKHORI M, METSELAAR H S C, MAHLIA T M I, et al. Palmitic acid/polypyrrole composites as form-stable phase change materials for thermal energy storage[J]. Energy Conversion & Management, 2014, 80(2):491-497.
[9]	付路军, 董发勤, 杨玉山, 等. 二元脂肪酸/SiO2复合相变储能材料的制备与表征[J]. 功能材料, 2013, 44(4):548-551. FU L J, DONG F Q, YANG Y S, et al. Preparation and characterization of diatomic fatty acids/SiO2 composite phase change energy storage material[J]. Journal of Functional Materials, 2013, 44(4):548-551.
[10]	李爱菊, 王毅. 无机盐/陶瓷基复合蓄热材料高温稳定性的研究[J]. 材料导报, 2011, 25(12):78-81. LI A J, WANG Y. Study on the high temperature stability of salt/ceramic composite heat storage material[J]. Materials Review, 2011, 25(12):78-81.
[11]	林健, 郭郊, 赵宇, 等. 硅藻土/聚氨酯多孔复合材料的组织结构与吸声特性[J]. 复合材料学报, 2014, 31(6):1476-1480. LIN J, GUO J, ZHAO Y, et al. Microstructure and sound absorption property of diatomite/polyurethane porous composites[J]. Acta Materiae Compositae Sinica, 2014, 31(6):1476-1480.
[12]	尚建丽, 麻向龙, 张磊, 等. 多孔载体相变材料的热湿综合性能[J]. 浙江大学学报(工学版), 2016, 50(5):879-886. SHANG J L, MA X L, ZHANG L, et al. Comprehensive properties of temperature and humidity of porous carrier phase change material[J]. Journal of Zhejiang University (Engineering Science), 2016, 50(5):879-886.
[13]	宋兵, 郑水林, 杨涛, 等. 硅藻土基复合材料的研究现状和发展前景[J]. 中国非金属矿工业导刊, 2012, 96(3):1-4. SONG B, ZHENG S L, YANG T, et al. Current situation and development of diatomite-based composites[J]. China Nonmetallic Minerals Industry, 2012, 96(3):1-4.
[14]	HADJAR H, HAMDI B, JABER M, et al. Elaboration and characterisation of new mesoporous materials from diatomite and charcoal[J]. Microporous & Mesoporous Materials, 2008, 107(3):219-226.
[15]	SARI A, BICER A. Thermal energy storage properties and thermal reliability of some fatty acid esters/building material composites as novel form-stable PCMs[J]. Solar Energy Materials & Solar Cells, 2012, 101(6):114-122.
[16]	NOMURA T, OKINAKA N, AKIYAMA T. Impregnation of porous material with phase change material for thermal energy storage[J]. Materials Chemistry & Physics, 2009, 115(2/3):846-850.
[17]	QIAN T, LI J, MIN X, et al. Diatomite:a promising natural candidate as carrier material for low, middle and high temperature phase change material[J]. Energy Conversion & Management, 2015, 98(3):34-45.
[18]	付路军, 董发勤, 何平, 等. 癸酸-肉豆蔻酸/硅藻土定形相变储能材料制备及性能研究[J]. 功能材料, 2013, 44(10):1465-1468. FU L J, DONG F Q, HE P, et al. Study on preparation and properties of decanoic acid-tetradecanoic acid/diatomite phase change energy storage materials[J]. Journal of Functional Materials, 2013, 44(10):1465-1468.
[19]	刘娟红, 宋少民. 硅酸钙石棉复合保温灰的研制[J]. 新型建筑材料, 1994, (1):38-39. LIU J H, SONG S M. Preparation of calcium silicate asbestos composite thermal insulation ash[J]. New Building Materials, 1994, (1):38-39.
[20]	于漧. 我国轻骨料和轻骨料砌块的现状与展望[J]. 建材工业信息, 1996, 23(23):4-5. YU Q. Present situation and prospect of lightweight aggregate and light aggregate block in China[J]. Brick & Tile World, 1996, 23(23):4-5.
[21]	肖力光, 杨艳敏, 常继国. 硅藻土对氯氧镁水泥性能的影响[J]. 吉林建材, 2000, 81(1):23-26. XIAO L G, YANG Y M, CHANG J G. Influence of diatomite on properties of magnesium oxychloride cement[J]. Jilin Building Materials, 2000, 81(1):23-26.
[22]	FRAGOULIS D, STAMATAKIS M G. Characterization of lightweight aggregates produced with clayey diatomite rocks originating from Greece[J]. Materials Characterization, 2004, 53(2):307-316.
[23]	YILMAZ B, EDIZ N. The use of raw and calcined diatomite in cement production[J]. Cement & Concrete Composites, 2008, 30(3):202-211.
[24]	DENG Y, LI J, QIAN T, et al. Preparation and characterization of KNO3/diatomite shape-stabilized composite phase change material for high temperature thermal energy storage[J]. Journal of Materials Science & Technology, 2017, 33(2):198-203.
[25]	KARAMAN S, KARAIPEKLI A, SARI A, et al. Polyethylene glycol (PEG)/diatomite composite as a novel form-stable phase change material for thermal energy storage[J]. Solar Energy Materials & Solar Cells, 2011, 95(7):1647-1653.
[26]	XU B, LI Z. Paraffin/diatomite composite phase change material incorporated cement-based composite for thermal energy storage[J]. Applied Energy, 2013, 105(2):229-237.
[27]	LI X, SANJAYAN J G, WILSON J L. Fabrication and stability of form-stable diatomite/paraffin phase change material composites[J]. Energy & Buildings, 2014, 76(2):284-294.
[28]	NOMURA T, OKINAKA N, AKIYAMA T. Impregnation of porous material with phase change material for thermal energy storage[J]. Materials Chemistry & Physics, 2009, 115(2/3):846-850.
[29]	席国喜, 杨文洁. 硬脂酸/改性硅藻土复合相变储能材料的制备及性能研究[J]. 材料导报, 2009, 23(16):45-50. XI G X, YANG W J. Preparation and study of stearic acid/modified kieselguhr composite phase change material[J]. Materials Review, 2009, 23(16):45-50.
[30]	孙跃枝, 席国喜, 杨文洁, 等. 石蜡/改性硅藻土复合相变储能材料的制备及性能研究[J]. 化工新型材料, 2010, 38(4):46-48. SUN Y Z, XI G X, YANG W J, et al. Preparation and study on paraffin/modified kieselguhr composite phase change material[J]. New Chemical Materials, 2010, 38(4):46-48.
[31]	宋秀龙, 康虹, 高向华, 等. 硅藻土吸附正十八烷高相变焓复合相变材料的制备及其性能研究[J]. 材料导报, 2015, 29(9):40-45. SONG X L, KANG H, GAO X H, et al. Preparation and properties of a composite phase change material of diatomite/n-octadecane with high enthalpy[J]. Materials Review, 2015, 29(9):40-45.
[32]	冷光辉, 秦月, 叶锋, 等. 硅藻土基复合相变储热材料研究现状[J]. 储能科学与技术, 2013, 2(3):199-207. LENG G H, QIN Y, YE F, et al. Recent progress in diatomite based composite phase change materials for thermal energy storage[J]. Energy Storage Science and Technology, 2013, 2(3):199-207.
[33]	XU G Z, LENG G H, YANG C Y, et al. Sodium nitrate-diatomite composite materials for thermal energy storage[J]. Sol. Energy, 2017, 146(4):494-502.
[34]	QIN Y, LENG G H, YU X, et al. Sodium sulfate-diatomite composite materials for high temperature thermal energy storage[J]. Powder Technology, 2015, 282(9):37-42.
[35]	JIANG Z, LENG G H, YE F, et al. Form-stable LiNO3-NaNO3-KNO3-Ca(NO3)2/calcium silicate composite phase change material (PCM) for mid-low temperature thermal energy storage[J]. Energy Conversation Management, 2015, 106(12):165-72.
[36]	ZHAO B, LI C, JIN Y, et al. Heat transfer performance of thermal energy storage components containing composite phase change materials[J]. IET Renewable Power Generation, 2016, 10:1515-1522.
[37]	秦月. 硅藻土基中高温复合相变储能材料工艺及性能的研究[D]. 北京:中国地质大学(北京), 2013. QIN Y. A study of technology and properties for diatomite matrix thermal storage materials[D]. Beijing:China University of Geosciences (Beijing), 2013.

载体含量对NaNO₃/硅藻土复合相变储热材料的性能影响规律

Effects of carrier on characteristics of NaNO₃/diatomite composite phase change materials for thermal energy storage

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献 37

相关文章 15

编辑推荐

Metrics

本文评价

[1]	张双星, 刘舫辰, 张义飞, 杜文静. R-134a脉动热管相变蓄放热实验研究[J]. 化工学报, 2023, 74(S1): 165-171.
[2]	江河, 袁俊飞, 王林, 邢谷雨. 均流腔结构对微细通道内相变流动特性影响的实验研究[J]. 化工学报, 2023, 74(S1): 235-244.
[3]	吴延鹏, 刘乾隆, 田东民, 陈凤君. 相变材料与热管耦合的电子器件热管理研究进展[J]. 化工学报, 2023, 74(S1): 25-31.
[4]	晁京伟, 许嘉兴, 李廷贤. 基于无管束蒸发换热强化策略的吸附热池的供热性能研究[J]. 化工学报, 2023, 74(S1): 302-310.
[5]	杨学金, 杨金涛, 宁平, 王访, 宋晓双, 贾丽娟, 冯嘉予. 剧毒气体PH₃的干法净化技术研究进展[J]. 化工学报, 2023, 74(9): 3742-3755.
[6]	盛冰纯, 于建国, 林森. 铝基锂吸附剂分离高钠型地下卤水锂资源过程研究[J]. 化工学报, 2023, 74(8): 3375-3385.
[7]	张瑞航, 曹潘, 杨锋, 李昆, 肖朋, 邓春, 刘蓓, 孙长宇, 陈光进. ZIF-8纳米流体天然气乙烷回收工艺的产品纯度关键影响因素分析[J]. 化工学报, 2023, 74(8): 3386-3393.
[8]	胡兴枝, 张皓焱, 庄境坤, 范雨晴, 张开银, 向军. 嵌有超小CeO₂纳米粒子的碳纳米纤维的制备及其吸波性能[J]. 化工学报, 2023, 74(8): 3584-3596.
[9]	高燕, 伍鹏, 尚超, 胡泽君, 陈晓东. 基于双流体喷嘴的磁性琼脂糖微球的制备及其蛋白吸附性能探究[J]. 化工学报, 2023, 74(8): 3457-3471.
[10]	史昊鹏, 钟达文, 廉学新, 张君峰. 朝下多尺度沟槽翅片结构表面沸腾换热实验研究[J]. 化工学报, 2023, 74(7): 2880-2888.
[11]	史方哲, 甘云华. 超薄热管启动特性和传热性能数值模拟[J]. 化工学报, 2023, 74(7): 2814-2823.
[12]	陈吉, 洪泽, 雷昭, 凌强, 赵志刚, 彭陈辉, 崔平. 基于分子动力学的焦炭溶损反应及其机理研究[J]. 化工学报, 2023, 74(7): 2935-2946.
[13]	邢美波, 张中天, 景栋梁, 张洪发. 磁调控水基碳纳米管协同多孔材料强化相变储/释能特性[J]. 化工学报, 2023, 74(7): 3093-3102.
[14]	张贲, 王松柏, 魏子亚, 郝婷婷, 马学虎, 温荣福. 超亲水多孔金属结构驱动的毛细液膜冷凝及传热强化[J]. 化工学报, 2023, 74(7): 2824-2835.
[15]	张澳, 罗英武. 低模量、高弹性、高剥离强度丙烯酸酯压敏胶[J]. 化工学报, 2023, 74(7): 3079-3092.