高气液密度比的传热相变复合模型

doi:10.11949/j.issn.0438-1157.20180021

化工学报 ›› 2018, Vol. 69 ›› Issue (8): 3418-3427.DOI: 10.11949/j.issn.0438-1157.20180021

高气液密度比的传热相变复合模型

刘冰冰¹, 王明雨¹, 高洪涛², 张少君¹

1 山东交通学院船舶与轮机工程学院, 山东威海 264310;
2 大连海事大学轮机工程学院, 辽宁大连 116026

收稿日期:2018-01-09 修回日期:2018-05-21 出版日期:2018-08-05 发布日期:2018-08-05
通讯作者: 张少君
基金资助:
国家自然科学基金项目（51609131）；山东省自然科学基金项目（ZR2014JL038，ZR2017MEE031）。

Composite model of heat transfer and phase transition with high gas and liquid density ratio

LIU Bingbing¹, WANG Mingyu¹, GAO Hongtao², ZHANG Shaojun¹

1 College of Naval Architecture and Marine Engineering, Shandong Jiaotong University, Weihai 264310, Shandong, China;
2 Institute of Marine Engineering, Dalian Maritime University, Dalian 116026, Liaoning, China

Received:2018-01-09 Revised:2018-05-21 Online:2018-08-05 Published:2018-08-05
Supported by:
supported by the National Natural Science Foundation of China (51609131) and the Natural Science Foundation of Shandong Province (ZR2014JL038, ZR2017MEE031).

摘要/Abstract

摘要：

为研究两相流动中热量传递机制，基于格子Boltzmann热模型及大密度比模型，将相变源项引入到控制两相密度分布函数中，来描述温度场对气液相变的影响，提出了一个可以描述气液密度比达到2778的传热相变复合模型。通过对压力速度分布函数的回归修正克服了气液密度比过大造成的数值不稳定问题。模拟了溴化锂水溶液中双气泡的上升运动过程及周围的温度场分布，研究发现：双气泡上升时，碰撞前上方气泡温度高于下方气泡，碰撞时，两气泡间液桥打开，发生热量传递，气泡内部温度变得均匀；双气泡体积先减小再增大，碰撞时体积达到最大值，在融合成一个气泡后体积逐渐缩小，最终趋于稳定；初始气泡的体积越大，气泡上升过程中的速度越大。

关键词: 格子Boltzmann方法, 数值模拟, 气泡, 流动, 传热

Abstract:

Based on lattice Boltzmann thermal model and large density ratio model, a phase transition source term was introduced into two-phase density distribution control function to describe effect of temperature field on gas-liquid phase transition. A composite lattice Boltzmann thermal model, which can describe heat transfer and phase transition at gas-liquid ratio up to 2778, was proposed to study two-phase heat transfer mechanism. Numerical instability caused by extremely large gas-liquid density ratio was resolved by regress correction of pressure velocity distribution function. Double bubble rising movement and the surrounding temperature field distribution in lithium bromide solution was simulated using the model. Upper bubble temperature was higher than that of lower bubble prior to collision during moving up. Upon coalescence, liquid bridge between the two bubbles was open, heat transfer started and temperature inside the bubble became uniform. The volume of the double bubbles decreased first and then increased with maximum at time of two bubbles collision. After bubble coalescence, the volume gradually decreased and eventually stabilized to certain value. The larger the initial bubble volume is, the greater the velocity of the bubble rises.

Key words: lattice Boltzmann method, numerical simulation, bubble, flow, heat transfer

中图分类号:

O359

刘冰冰, 王明雨, 高洪涛, 张少君. 高气液密度比的传热相变复合模型[J]. 化工学报, 2018, 69(8): 3418-3427.

LIU Bingbing, WANG Mingyu, GAO Hongtao, ZHANG Shaojun. Composite model of heat transfer and phase transition with high gas and liquid density ratio[J]. CIESC Journal, 2018, 69(8): 3418-3427.

参考文献 31

[1]	SHEN B, YAMADA M, HIDAKA S, et al. Early onset of nucleate boiling on gas-covered biphilic surfaces[J]. Scientific Reports, 2017, 7(1):2036.
[2]	KHESTANOVA E, GUINEA F, FUMAGALLI L, et al. Universal shape and pressure inside bubbles appearing in van der Waals heterostructures[J]. Nature Communications, 2016, 7:12587.
[3]	吴迎亚, 彭丽, 高金森, 等. 基于EMMS模型的气固鼓泡床的模拟及气泡特性的分析[J]. 化工学报, 2016, 67(8):3259-3267. WU Y Y, PENG L, GAO J S, et al. Numerical simulation of gas-solid bubbling bed and bubble characteristics based on EMMS drag model[J]. CIESC Journal, 2016, 67(8):3259-3267.
[4]	吕雅琪, 聂德明, 林建忠. 三维双气泡融合的格子Boltzmann模拟[J]. 计算物理, 2015, (5):553-560. LÜ Y Q, NIE D M, LIN J Z. Lattice Boltzmann simulation of gas bubble merging in three dimensions[J]. Chinese Journal of Computational Physics, 2015, (5):553-560.
[5]	WANG Y, CAI J, LI Q, et al. Diffuse interface simulation of bubble rising process:a comparison of adaptive mesh refinement and arbitrary Lagrange-Euler methods[J]. Heat & Mass Transfer, 2018, 54(6):1767-1778.
[6]	ROUDET M, BILLE A, CAZIN S, et al. Experimental investigation of interfacial mass transfer mechanisms for a confined high-Reynolds number bubble rising in a thin gap[J]. AIChE Journal, 2017, 63(6):2394-2408.
[7]	HUANG J, SAITO T. Discussion about the differences in mass transfer, bubble motion and surrounding liquid motion between a contaminated system and a clean system based on consideration of three-dimensional wake structure obtained from LIF visualization[J]. Chemical Engineering Science, 2017, 170:105-115.
[8]	GUNSTENSEN A K, ROTHMAN D H, ZALESKI S, et al. Lattice Boltzmann model of immiscible fluids[J]. Physical Review A, 1991, 43(8):4320-4327.
[9]	SHAN X, CHEN H. Lattice Boltzmann model for simulating flows with multiple phases and components[J]. Physical Review E Statistical Physics Plasmas Fluids & Related Interdisciplinary Topics, 1993, 47(3):1815-1819.
[10]	QIAN Y H, CHEN S Y. Finite size effect in lattice-BGK model[J]. International Journal of Modern Physics C, 1997, 8(4):763-771.
[11]	SWIFT M, OBSBOME W, YEOMANS J. Lattice Boltzmann simulation of nonideal fluids[J]. Physical Review Letter, 1995, 75(5):830-833.
[12]	HE X Y, SHAN X W, DOOLEN G D. Discrete Boltzmann equation model for nonideal gases[J]. Physical Review E, 1998, 57(1):13-16.
[13]	GUO Z L, ZHAO T S. Discrete velocity and lattice Boltzmann models for binary mixtures of nonideal fluids[J]. Physical Review E, 2003, 68(3):035302-035312.
[14]	张潇丹, 雍玉梅, 李文军, 等. REV尺度多孔介质格子Boltzmann方法的数学模型及应用的研究进展[J]. 化工进展, 2016, 35(6):1698-1712. ZHANG X D, YONG Y M, LI W J, et al. Models and application of lattice Boltzmann method at REV-scale in porous media[J]. Chemical Industry and Engineering Progress, 2016, 35(6):1698-1712.
[15]	TENG S, CHEN Y, OHASHI H. Lattice Boltzmann simulation of multiphase fluid flows through the total variation diminishing artificial compression scheme[J]. International Journal of Heat and Fluid Flow, 2000, 21(1):112-121.
[16]	WERZNER X, MIGUEL A, MENDES A, et al. Numerical investigation on the depth filtration of liquid metals:influence of process conditions and inclusion properties[J]. Advanced Engineering Materials, 2015, 15(12):1037-1314.
[17]	LEE T, LIN C L. A stable discretization of the lattice Boltzmann equation for simulation of incompressible two-phase flows at high density ratio[J]. Journal of Computational Physics, 2005, 206(1):16-47.
[18]	INAMURO T, OGATA T, TAJIMA S, et al. A lattice Boltzmann method for incompressible two-phase flows with large density differences[J]. Journal of Computational Physics, 2004, 198(2):628-644.
[19]	KATAOKA T, TSUTAHARA M. Lattice Boltzmann model for the compressible Navier-Stokes equations with flexible specific-heat ratio[J]. Physical Review E, 2004, 69(2):035701.
[20]	孙涛, 李维仲, 杨柏丞, 等. 气泡群上升过程相互作用的格子Boltzmann三维数值模拟[J]. 化工学报, 2013, 64(5):1586-1591. SUN T, LI W Z, YANG B C, et al. Three-dimensional numerical simulation of multiple bubbles rising and interaction with lattice Boltzmann method[J]. CIESC Journal, 2013, 64(5):1586-1591.
[21]	CHEN H N, SUN D K, DAI T, et al. Modeling of the interaction between solidification interface and bubble using the lattice Boltzmann method with large density ratio[J]. Acta Phys. Sin., 2013, 62(12):120502.
[22]	ALEXANDER F J, CHEN S, STERLING J D. Lattice Boltzmann thermohydrodynamics[J]. Physical Review E Statistical Physics Plasmas Fluids & Related Interdisciplinary Topics, 1993, 47(4):R2249.
[23]	QIAN Y H. Simulating thermohydrodynamics with lattice BGK models[J]. Journal of Scientific Computing, 1993, 8(3):231-242.
[24]	CHEN Y, OHASHI H, AKIYAMA M. Two-parameter thermal lattice BGK model with a controllable Prandtl number[J]. Journal of Scientific Computing, 1997, 12(2):169-185.
[25]	BARTOLONI A, BATTISTA C, CABASINO S, et al. Lbe simulations of Rayleigh-Bénard convection on the ape100 parallel processor[J]. International Journal of Modern Physics C, 2011, 4(5):993-1006.
[26]	SHAN X. Simulation of Rayleigh-Bénard convection using lattice Boltzmann method[J]. Physical Review E Statistical Physics Plasmas Fluids & Related Interdisciplinary Topics, 1998, 55(3):2780-2788.
[27]	PALMER B J, RECTOR D R. Lattice-Boltzmann algorithm for simulating thermal two-phase flow[J]. Phys. Rev. E Stat. Phys. Plasmas Fluids Relat. Interdiscip. Topics, 2000, 61(5A):5295-5306.
[28]	GUO Z, SHI B, ZHENG C. A coupled lattice BGK model for the Boussinesq equations[J]. International Journal for Numerical Methods in Fluids, 2002, 39(4):325-342.
[29]	王佐, 张家忠, 王恒. 非正交多松弛系数轴对称热格子Boltzmann方法[J]. 物理学报, 2017, 66(4):156-168. WANG Z, ZHANG J Z, WANG H. Non-orthogonal multiple-relaxation time lattice Boltzmann method for axisymmetric thermal flows[J]. Acta Phys. Sin., 2017, 66(4):156-168.
[30]	INAMURO T, YOSHINO M, INOUE H, et al. A lattice Boltzmann method for a binary miscible fluid mixture and its application to a heat-transfer problem[J]. Journal of Computational Physics, 2002, 179(1):201-215.
[31]	CHORIN A J. Numerical solution of the Navier-Stokes equations[J]. Math. Comput., 1968, 22(104):745-762.

高气液密度比的传热相变复合模型

Composite model of heat transfer and phase transition with high gas and liquid density ratio

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献 31

相关文章 15

编辑推荐

Metrics

本文评价

[1]	宋嘉豪, 王文. 斯特林发动机与高温热管耦合运行特性研究[J]. 化工学报, 2023, 74(S1): 287-294.
[2]	张思雨, 殷勇高, 贾鹏琦, 叶威. 双U型地埋管群跨季节蓄热特性研究[J]. 化工学报, 2023, 74(S1): 295-301.
[3]	晁京伟, 许嘉兴, 李廷贤. 基于无管束蒸发换热强化策略的吸附热池的供热性能研究[J]. 化工学报, 2023, 74(S1): 302-310.
[4]	程成, 段钟弟, 孙浩然, 胡海涛, 薛鸿祥. 表面微结构对析晶沉积特性影响的格子Boltzmann模拟[J]. 化工学报, 2023, 74(S1): 74-86.
[5]	肖明堃, 杨光, 黄永华, 吴静怡. 浸没孔液氧气泡动力学数值研究[J]. 化工学报, 2023, 74(S1): 87-95.
[6]	宋瑞涛, 王派, 王云鹏, 李敏霞, 党超镔, 陈振国, 童欢, 周佳琦. 二氧化碳直接蒸发冰场排管内流动沸腾换热数值模拟分析[J]. 化工学报, 2023, 74(S1): 96-103.
[7]	周绍华, 詹飞龙, 丁国良, 张浩, 邵艳坡, 刘艳涛, 郜哲明. 短管节流阀内流动噪声的实验研究及降噪措施[J]. 化工学报, 2023, 74(S1): 113-121.
[8]	叶展羽, 山訸, 徐震原. 用于太阳能蒸发的折纸式蒸发器性能仿真[J]. 化工学报, 2023, 74(S1): 132-140.
[9]	邵苛苛, 宋孟杰, 江正勇, 张旋, 张龙, 高润淼, 甄泽康. 水平方向上冰中受陷气泡形成和分布实验研究[J]. 化工学报, 2023, 74(S1): 161-164.
[10]	张双星, 刘舫辰, 张义飞, 杜文静. R-134a脉动热管相变蓄放热实验研究[J]. 化工学报, 2023, 74(S1): 165-171.
[11]	张义飞, 刘舫辰, 张双星, 杜文静. 超临界二氧化碳用印刷电路板式换热器性能分析[J]. 化工学报, 2023, 74(S1): 183-190.
[12]	陈爱强, 代艳奇, 刘悦, 刘斌, 吴翰铭. 基板温度对HFE7100液滴蒸发过程的影响研究[J]. 化工学报, 2023, 74(S1): 191-197.
[13]	刘明栖, 吴延鹏. 导光管直径和长度对传热影响的模拟分析[J]. 化工学报, 2023, 74(S1): 206-212.
[14]	王志国, 薛孟, 董芋双, 张田震, 秦晓凯, 韩强. 基于裂隙粗糙性表征方法的地热岩体热流耦合数值模拟与分析[J]. 化工学报, 2023, 74(S1): 223-234.
[15]	李艺彤, 郭航, 陈浩, 叶芳. 催化剂非均匀分布的质子交换膜燃料电池操作条件研究[J]. 化工学报, 2023, 74(9): 3831-3840.