制冷剂在微通道扁平T型管内的气液两相流相分配特性研究

doi:10.11949/0438-1157.20200915

化工学报 ›› 2021, Vol. 72 ›› Issue (4): 2057-2064.DOI: 10.11949/0438-1157.20200915

制冷剂在微通道扁平T型管内的气液两相流相分配特性研究

徐肖肖¹(),张世杰¹,李怡^1,²,刘朝¹

^1.重庆大学能源与动力工程学院，低品位能源利用技术及系统教育部重点实验室，重庆 400030
^2.海信家电集团股份有限公司，广东佛山 528303

收稿日期:2020-07-07 修回日期:2020-09-26 出版日期:2021-04-05 发布日期:2021-04-05
通讯作者: 徐肖肖
作者简介:徐肖肖（1980—），女，博士，教授，xuxiaoxiao@cqu.edu.cn
基金资助:
国家自然科学基金项目(51776020);中央高校基本科研业务费专项资金(2019CDQYDL035)

Study on phase distribution characteristics of gas-liquid two-phase flow in micro-channel flat T-junction

XU Xiaoxiao¹(),ZHANG Shijie¹,LI Yi^1,²,LIU Chao¹

^1.Key Laboratory of Low-grade Energy Utilization Technologies and Systems, Ministry of Education, College of Energy and Power Engineering, Chongqing University, Chongqing 400030, China
^2.Hisense Kelon Electrical Holdings Company Limited, Foshan 528303, Guangdong, China

Received:2020-07-07 Revised:2020-09-26 Online:2021-04-05 Published:2021-04-05
Contact: XU Xiaoxiao

摘要/Abstract

摘要：

气液两相流在常规T型管内的相分配特性已得到充分研究，但少有文献关注微通道扁平T型管内的两相流分配特性。以两相制冷剂R134a为工质，对扁平T型管内的相分配特性进行了实验研究。实验结果表明，气液两相流在扁平T型管内的液相进口流速增加会使液相分离比减小，气相分离比增大；进口干度增加使液相分离比增大，气相分离比减小；气相进口流速对扁平T型管内泡状流的相分配影响较小。由相分配模型预测值与实验值对比可知，现有的相分配模型还无法准确预测扁平T型管内泡状流的气液相分离比。在进口干度为0.45~0.5时扁平T型管内制冷剂R134a气液相分配比较均匀。

关键词: 两相流, 相分配特性, 扁平管, T型管, 微通道, 气液相分离比

Abstract:

The phase distribution characteristics of gas-liquid two-phase flow in conventional T-junction have been fully studied, but few literatures have paid attention to the distribution characteristics of two-phase flow in micro-channel flat T-junction. Using the two-phase refrigerant R134a as the working fluid, the phase distribution characteristics in the flat T-junction are studied experimentally. The results show that the increase of the liquid-phase inlet flow rate of the two-phase flow in the flat T-junction will decrease the liquid-phase separation ratio and increase the gas-phase separation ratio. The increase of the inlet quality will increase the liquid-phase separation ratio and decrease the gas-phase separation ratio. The gas inlet velocity has little effect on the phase distribution of the bubbly flow in the flat T-junction. It can be seen from the comparison between the predicted phase distribution model and the experimental value that the existing phase distribution model cannot accurately predict the gas-liquid separation ratio of the bubbly flow in the flat T-junction. In the experimental conditions, when the inlet dryness is 0.45—0.5, the refrigerant R134a in the flat T-junction has a relatively uniform gas and liquid distribution.

Key words: two-phase flow, phase distribution characteristics, flat tube, T-junction tube, micro-channel, gas-liquid separation ratio

中图分类号:

TQ 028.8

徐肖肖, 张世杰, 李怡, 刘朝. 制冷剂在微通道扁平T型管内的气液两相流相分配特性研究[J]. 化工学报, 2021, 72(4): 2057-2064.

XU Xiaoxiao, ZHANG Shijie, LI Yi, LIU Chao. Study on phase distribution characteristics of gas-liquid two-phase flow in micro-channel flat T-junction[J]. CIESC Journal, 2021, 72(4): 2057-2064.

参考文献 30

1	Kim N H, Byun H W, Sim Y S. Upward branching of two-phase refrigerant in a parallel flow minichannel heat exchanger[J]. Experimental Thermal and Fluid Science, 2013, 51: 189-203.
2	刘巍, 朱春玲. 分流板结构对微通道平行流蒸发器性能的影响[J]. 化工学报, 2012, 63(3): 761-766.
	Liu W, Zhu C L. Effects of deflector structure on performance of micro-channel evaporator with parallel flow[J]. CIESC Journal, 2012, 63(3): 761-766.
3	徐肖肖, 肖久旻, 陈龙, 等. 平行流换热器两相流分配模型的建立与验证[J]. 化工学报, 2018, 69(5): 1938-1945.
	Xu X X, Xiao J M, Chen L, et al. Establishment and verification of a two-phase flow distribution model in a parallel flow heat exchanger[J]. CIESC Journal, 2018, 69(5): 1938-1945.
4	舒朝晖, 李丛来, 陈焕新, 等. 扁管结构对平行流冷凝器制冷剂侧性能的影响[J]. 化工学报, 2008, 59: 129-133.
	Shu Z H, Li C L, Chen H X, et al. Fiat tube structure on refrigerant-side performance of parallel flow type condenser[J]. Journal of Chemical Industry and Engineering (China), 2008, 59: 129-133.
5	Kulkarni T, Bullard C W, Cho K. Header design tradeoffs in microchannel evaporators[J]. Applied Thermal Engineering, 2004, 24(5/6): 759-776.
6	Saieed A, Pao W, Hashim F M. Effect of T-junction diameter ratio on stratified-wavy flow separation[J]. Journal of Natural Gas Science and Engineering, 2018, 51: 223-232.
7	何奎, 汪双凤, 黄间珍. 气液两相流在微小T型三通中的相分配特性[J]. 化工学报, 2011, 62: 92-96.
	He K, Wang S F, Huang J Z. Phase split characteristic of two-phase flow through a micro-T-junction[J]. CIESC Journal, 2011, 62: 92-96.
8	Tae S J, Cho K. Two-phase split of refrigerants at a T-junction[J]. International Journal of Refrigeration, 2006, 29(7): 1128-1137.
9	Su W, Hwang Y, Deng S, et al. Experimental study on phase separation of refrigerant at horizontal T-junction[J]. International Journal of Multiphase Flow, 2018, 105: 217-233.
10	Shoham O, Brill J P, Taitel Y. Two-phase flow splitting in a tee junction—experiment and modelling[J]. Chemical Engineering Science, 1987, 42(11): 2667-2676.
11	Ballyk J D, Shoukri M. On the development of a model for predicting phase separation phenomena in dividing two-phase flow[J]. Nuclear Engineering and Design, 1990, 123(1): 67-75.
12	Lu P, Zhao L, Deng S, et al. Simulation of two-phase refrigerant separation in horizontal T-junction[J]. Applied Thermal Engineering, 2018, 134: 333-340.
13	Chen J F, He K, Huang J Z, et al. Study of phase splitting at a micro-T-junction[J]. Heat Transfer Engineering, 2014, 35(11/12): 1114-1121.
14	Ren T, Ding G L, Wang T T, et al. A general three-dimensional simulation approach for micro-channel heat exchanger based on graph theory[J]. Applied Thermal Engineering, 2013, 59(1/2): 660-674.
15	Hwang S T, Soliman H M, Lahey R T. Phase separation in dividing two-phase flows[J]. International Journal of Multiphase Flow, 1988, 14(4): 439-458.
16	Azzi A, Al-Attiyah A, Qi L, et al. Gas-liquid two-phase flow division at a micro-T-junction[J]. Chemical Engineering Science, 2010, 65(13): 3986-3993.
17	He K, Wang S F, Huang J Z. The effect of surface tension on phase distribution of two-phase flow in a micro-T-junction[J]. Chemical Engineering Science, 2011, 66(17): 3962-3968.
18	Li H W, Li J W, Zhou Y L, et al. Phase split characteristics of slug and annular flow in a dividing micro-T-junction[J]. Experimental Thermal and Fluid Science, 2017, 80: 244-258.
19	陈龙. 基于微通道扁平管的T型管压降特性和流量分配特性研究[D]. 重庆: 重庆大学, 2018.
	Chen L. Study on pressure drop characteristic and flow separation of the reduced T-junction with microchannel flat tube[D]. Chongqing: Chongqing University, 2018.
20	Usui K, Sato K. Vertically downward two-phase flow (I)[J]. Journal of Nuclear Science and Technology, 1989, 26(7): 670-680.
21	Barnea D, Shoham O, Taitel Y. Flow pattern transition for vertical downward two phase flow[J]. Chemical Engineering Science, 1982, 37(5): 741-744.
22	Kendoush A A, Al-Khatab S A W. Experiments on flow characterization in vertical downward two-phase flow[J]. Experimental Thermal and Fluid Science, 1994, 9(1): 34-38.
23	Goda H, Hibiki T, Kim S, et al. Drift-flux model for downward two-phase flow[J]. International Journal of Heat and Mass Transfer, 2003, 46(25): 4835-4844.
24	Hewitt G F, Roberts D N. Studies of two-phase flow patterns by simultaneous X-ray and flash photography[R]. United Kingdom Atomic Energy Authority Report AERE-M 2159,1969.
25	Weisman J, Kang S Y. Flow pattern transitions in vertical and upwardly inclined lines[J]. International Journal of Multiphase Flow, 1981, 7(3): 271-291.
26	Mak C Y, Omebere-Iyari N K, Azzopardi B J. The split of vertical two-phase flow at a small diameter T-junction[J]. Chemical Engineering Science, 2006, 61(19): 6261-6272.
27	Azzopardi B J. Measurements and observations of the split of annular flow at a vertical T-junction[J]. International Journal of Multiphase Flow, 1988, 14(6): 701-710.
28	Beaver A C, Yin J M, Hrnjak P S, et al. Effects of distribution in headers of microchannel evaporators on transcritical CO₂heat pump performance[C]//Proc. ASME. 2000.
29	Hart J, Hamersma P J, Fortuin J M H. Phase distribution during gas-liquid flow through horizontal dividing junctions[J]. Nuclear Engineering and Design, 1991, 126(3): 293-312.
30	Azzopardi B J, Whalley P B. The effect of flow patterns on two-phase flow in a T junction[J]. International Journal of Multiphase Flow, 1982, 8(5): 491-507.

[1]	周绍华, 詹飞龙, 丁国良, 张浩, 邵艳坡, 刘艳涛, 郜哲明. 短管节流阀内流动噪声的实验研究及降噪措施[J]. 化工学报, 2023, 74(S1): 113-121.
[2]	江河, 袁俊飞, 王林, 邢谷雨. 均流腔结构对微细通道内相变流动特性影响的实验研究[J]. 化工学报, 2023, 74(S1): 235-244.
[3]	肖明堃, 杨光, 黄永华, 吴静怡. 浸没孔液氧气泡动力学数值研究[J]. 化工学报, 2023, 74(S1): 87-95.
[4]	温凯杰, 郭力, 夏诏杰, 陈建华. 一种耦合CFD与深度学习的气固快速模拟方法[J]. 化工学报, 2023, 74(9): 3775-3785.
[5]	王玉兵, 李杰, 詹宏波, 朱光亚, 张大林. R134a在菱形离散肋微小通道内的流动沸腾换热实验研究[J]. 化工学报, 2023, 74(9): 3797-3806.
[6]	何松, 刘乔迈, 谢广烁, 王斯民, 肖娟. 高浓度水煤浆管道气膜减阻两相流模拟及代理辅助优化[J]. 化工学报, 2023, 74(9): 3766-3774.
[7]	袁佳琦, 刘政, 黄锐, 张乐福, 贺登辉. 泡状入流条件下旋流泵能量转换特性研究[J]. 化工学报, 2023, 74(9): 3807-3820.
[8]	刘文竹, 云和明, 王宝雪, 胡明哲, 仲崇龙. 基于场协同和耗散的微通道拓扑优化研究[J]. 化工学报, 2023, 74(8): 3329-3341.
[9]	高燕, 伍鹏, 尚超, 胡泽君, 陈晓东. 基于双流体喷嘴的磁性琼脂糖微球的制备及其蛋白吸附性能探究[J]. 化工学报, 2023, 74(8): 3457-3471.
[10]	邢雷, 苗春雨, 蒋明虎, 赵立新, 李新亚. 井下微型气液旋流分离器优化设计与性能分析[J]. 化工学报, 2023, 74(8): 3394-3406.
[11]	郭雨莹, 敬加强, 黄婉妮, 张平, 孙杰, 朱宇, 冯君炫, 陆洪江. 稠油管道水润滑减阻及压降预测模型修正[J]. 化工学报, 2023, 74(7): 2898-2907.
[12]	高金明, 郭玉娇, 鄂承林, 卢春喜. 一种封闭罩内顺流多旋臂气液分离器的分离特性研究[J]. 化工学报, 2023, 74(7): 2957-2966.
[13]	何宣志, 何永清, 闻桂叶, 焦凤. 磁液液滴颈部自相似破裂行为[J]. 化工学报, 2023, 74(7): 2889-2897.
[14]	牛超, 沈胜强, 杨艳, 潘泊年, 李熠桥. 甲烷BOG喷射器流动过程计算与性能分析[J]. 化工学报, 2023, 74(7): 2858-2868.
[15]	江锦波, 彭新, 许文烜, 门日秀, 刘畅, 彭旭东. 泵出型螺旋槽油气密封泄漏特性及参数影响研究[J]. 化工学报, 2023, 74(6): 2538-2554.

制冷剂在微通道扁平T型管内的气液两相流相分配特性研究

Study on phase distribution characteristics of gas-liquid two-phase flow in micro-channel flat T-junction

RichHTML

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献 30

相关文章 15

编辑推荐

Metrics

本文评价