绕管式换热器壳侧降膜流动和相变传热的数值模拟

doi:10.11949/j.issn.0438-1157.20150841

化工学报 ›› 2015, Vol. 66 ›› Issue (S2): 40-49.DOI: 10.11949/j.issn.0438-1157.20150841

绕管式换热器壳侧降膜流动和相变传热的数值模拟

李剑锐¹, 陈杰², 浦晖², 李恩道², 丁国良¹, 庄大伟¹, 胡海涛¹

1. 上海交通大学制冷与低温工程研究所, 上海 200240;
2. 中海石油气电集团技术研发中心, 北京 100028

收稿日期:2015-06-05 修回日期:2015-06-13 出版日期:2015-08-31 发布日期:2015-08-31
通讯作者: 丁国良
基金资助:
国家高技术研究发展计划项目(2013AA09A216)。

Simulation of falling film flow and heat transfer at shell-side of coil-wound heat exchanger

LI Jianrui¹, CHEN Jie², PU Hui², LI Endao², DING Guoliang¹, ZHUANG Dawei¹, HU Haitao¹

1. Institude of Refrigeration and Cryogenics, Shanghai Jiao Tong University, Shanghai 200240, China;
2. R & D Center, CNOOC Gas & Power Group, Beijing 100028, China

Received:2015-06-05 Revised:2015-06-13 Online:2015-08-31 Published:2015-08-31
Supported by:
supported by the National High Technology Research and Development Program of China(2013AA09A216).

摘要/Abstract

摘要：

为了定量描述绕管式换热器壳侧降膜蒸发特性并进而优化换热器结构,建立了绕管式换热器壳侧降膜蒸发过程流动与传热的数值模型。首先对降膜流动过程中流型变化和传热传质机理进行分析;通过对降膜流动过程液膜所受表面张力、重力和剪切力的计算,实现层状流、柱状流和滴状流等不同流型的模拟;通过管壁面和气液交界面的组分守恒建立降膜蒸发过程的传质子模型,并基于传质速率计算得出潜热传热速率。将数值模拟结果与已有文献中实验数据进行了对比,结果显示89%的模拟数据与实验数据偏差不超过25%;模拟结果与实验数据吻合较好。基于提出的模型,对不同工况下的绕管式换热器壳侧降膜蒸发传热传质规律进行了分析。

关键词: 绕管式换热器, 两相流, 液膜, 相变, 数值模拟

Abstract:

The objective of this paper is to develop a numerical model to predict the two-phase flow,heat transfer and mass transfer at shell-side of coil-wound heat exchangers(CWHEs),which can predict the performance of heat exchangers and optimize the structure of CWHE.To achieve this goal,the mechanism of the status of shell-side two-phase flow should be analyzed.Then,a model for simulating flow pattern,including the droplet flow,the column flow and the sheet flow,is developed by employing the volume of fluid-continuous surface force method;the mass transfer model is developed and mass transfer rate can be predicted on tube surface and liquid-gas interface;then the latent heat during evaporation and condensation can be calculated based on the mass transfer rates;the forces and the heat and mass transfer rates are introduced into the control equations as the source terms.The proposed model is validated by the experimental data from the existing references.There is good agreement between experimental data and predictions.The validation results show that 89% of the predicted data can agree with the experimental data within a deviation of ±25%. The heat and mass transfer coefficients obtained by the model are also analyzed.

Key words: coil-wound heat exchanger, two-phase flow, falling film, phase change, numerical model

中图分类号:

TK124

李剑锐, 陈杰, 浦晖, 李恩道, 丁国良, 庄大伟, 胡海涛. 绕管式换热器壳侧降膜流动和相变传热的数值模拟[J]. 化工学报, 2015, 66(S2): 40-49.

LI Jianrui, CHEN Jie, PU Hui, LI Endao, DING Guoliang, ZHUANG Dawei, HU Haitao. Simulation of falling film flow and heat transfer at shell-side of coil-wound heat exchanger[J]. CIESC Journal, 2015, 66(S2): 40-49.

参考文献 33

[1]	Shukri T.LNG technology selection[J].Hydrocarbon Engineering,2004,9(2):71-76.
[2]	Neeraas B O.Condensation of hydrocarbon mixtures in coil-wound LNG heat exchangers,tube-side heat transfer and pressure drop[D].Trondheim:Norwegian Institute of Technology,1993.
[3]	Pacio J C,Dorao C A.A review on heat exchanger thermal hydraulic models for cryogenic applications[J]. Cryogenics,2011,51(7):366-379.
[4]	Linde A G.Aluminium plate-fin heat exchangers[R].
[5]	Crawford D B,Eschenbrenner G P.Heat transfer equipment for LNG projects[J].Chem.Eng.Process,1972,68(9):62-70.
[6]	McKeever J,Pillarella M,Bower R.An ever evolving tech-nology[J].LNG Industry,2008:44-49.
[7]	Fredheim A O.Thermal design of coil-wound LNG heat exchangers shell-side heat transfer and pressure drop[D].Trondheim:University of Trondheim,1994.
[8]	Shokouhmand H,Salimpour M R,Akhavan-Behabadi M A.Experimental investigation of shell and coiled tube heat exchangers using Wilson plots[J].International Communi-cations in Heat and Mass Transfer,2008,35(1):84-92.
[9]	Aunan B.Shell-side heat transfer and pressure drop in coil-wound LNG heat exchangers,laboratory measurements and modeling[D].Trondheim:Norwegian University of Science and Technology,2000.
[10]	Neeraas B O,Fredheim A O,Aunan B.Experimental shell-side heat transfer and pressure drop in gas flow for spiral-wound LNG heat exchanger[J].International Journal of Heat and Mass Transfer,2004,47(2):353-361.
[11]	Neeraas B O,Fredheim A O,Aunan B.Experimental data and model for heat transfer,in liquid falling film flow on shell-side,for spiral-wound LNG heat exchanger[J].International Journal of Heat and Mass Transfer,2004,47(14):3565-3572.
[12]	Lu Xing,Du Xueping,Zeng Min,Zhang Sen,Wang Qiuwang.Shell-side thermal-hydraulic performances of multi-layer spiral-wound heat exchangers under different wall thermal boundary conditions[J].Applied Thermal Engineering,2014,70(2):1216-1227.
[13]	Killion J D,Garimella S.Simulation of pendant droplets and falling films in horizontal tube absorbers[J].Journal of Heat Transfer,2004,126(6):1003-1013.
[14]	Lei Xianliang(雷贤良),Li Huixiong(李会雄),Yan Libo(颜利波),et al.Numerical investigation on the offset characteristics of falling liquid columns over horizontal tubes under the interaction of inter-tube gas flows[J].Journal of Engineering Thermophysics(工程热物理学报),2010,31(11):1875-1878.
[15]	Wang Xiaofei(王小飞),He Maogang(何茂刚),Zhang Ying(张颖).Numerical simulation of the liquid flowing outside the tube of the horizontal-tube falling film evaporator[J].Journal of Engineering Thermophysics(工程热物理学报),2008,29(8):1347-1350.
[16]	Qiu Qinggang(邱庆刚),Chen Jinbo(陈金波).Nume-rical simulation of film formation on horizontal-tube falling film evaporators[J].Journal of Chinese Society of Power Engineering(动力工程学报),2011,31(5):357-361.
[17]	Luo L,Zhang G,Pan J,et al.Flow and heat transfer characteristics of falling water film on horizontal circular and non-circular cylinders[J].Journal of Hydrodynamics,2013,25(3):404-414.
[18]	Luo Lincong(罗林聪),Zhang Guanmin(张冠敏),Tian Maocheng(田茂诚),et al.Numerical simulation of liquid film flow on horizontal circular and shaped cylinders for falling film evaporation[J].Journal of Chinese Society of Power Engineering(动力工程学报),2013,34(4):710-714.
[19]	Luo L,Zhang G,Pan J,et al.Influence of oval-shaped tube on falling film flow characteristics on horizontal tube bundle[J].Desalination and Water Treatment,2015,54(11):2939.
[20]	Pise A T,Korde N U,Salunkhe R H.Numerical simulation of falling droplets/jets over horizontal tubes[J].Inter-national Journal of Fluid Mechanics Research,2013,40(3):266.
[21]	Chen J,Zhang R,Niu R.Numerical simulation of horizontal tube bundle falling film flow pattern transformation[J].Renewable Energy,2015, 73:62-68.
[22]	Inaoka H,Ito N.Numerical simulation of pool boiling of a Lennard-Jones liquid[J].Physica A:Statistical Mechanics and Its Applications,2013,392(18):3863-3868.
[23]	Gong S,Cheng P.Numerical simulation of pool boiling heat transfer on smooth surfaces with mixed wettability by lattice Boltzmann method[J].International Journal of Heat and Mass Transfer,2015,80:206-216.
[24]	Lal S,Sato Y,Niceno B.Direct numerical simulation of bubble dynamics in subcooled and near-saturated convective nucleate boiling[J].International Journal of Heat and Fluid Flow,2015,51:16.
[25]	Sun T,Li W,Yang S.Numerical simulation of bubble growth and departure during flow boiling period by lattice Boltzmann method[J].International Journal of Heat and Fluid Flow,2013,44:120-129.
[26]	Chen Z,Utaka Y.On heat transfer and evaporation charac-teristics in the growth process of a bubble with microlayer structure during nucleate boiling[J].International Journal of Heat and Mass Transfer,2015,81:750-759.
[27]	Tsui Y Y,Lin S W,Lai Y N,et al.Phase change calcula-tions for film boiling flows[J].International Journal of Heat and Mass Transfer,2014,70:745-757.
[28]	Kuang Y W,Wang W,Zhuan R,et al.Simulation of boiling flow in evaporator of separate type heat pipe with low heat flux[J].Annals of Nuclear Energy,2015,75:158-167.
[29]	Lee W,Son G,Yoon H Y.Direct numerical simulation of flow boiling in a finned microchannel[J].International Communications in Heat and Mass Transfer,2012,39(9):1460-1466.
[30]	Zhuan R,Wang W.Flow pattern of boiling in micro-channel by numerical simulation[J].International Journal of Heat and Mass Transfer,2012,55(5):1741-1753.
[31]	Wu H L,Peng X F,Ye P,et al.Simulation of refrigerant flow boiling in serpentine tubes[J].International Journal of Heat and Mass Transfer,2007,50(5):1186-1195.
[32]	Xie L,Xie Y,Yu J.Phase distributions of boiling flow in helical coils in high gravity[J].International Journal of Heat and Mass Transfer,2015,80:7-15.
[33]	Zhuan R,Wang W.Simulation on nucleate boiling in micro-channel[J].International Journal of Heat and Mass Transfer,2010,53(1):502-512.

绕管式换热器壳侧降膜流动和相变传热的数值模拟

Simulation of falling film flow and heat transfer at shell-side of coil-wound heat exchanger

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献 33

相关文章 15

编辑推荐

Metrics

本文评价

[1]	周绍华, 詹飞龙, 丁国良, 张浩, 邵艳坡, 刘艳涛, 郜哲明. 短管节流阀内流动噪声的实验研究及降噪措施[J]. 化工学报, 2023, 74(S1): 113-121.
[2]	叶展羽, 山訸, 徐震原. 用于太阳能蒸发的折纸式蒸发器性能仿真[J]. 化工学报, 2023, 74(S1): 132-140.
[3]	张双星, 刘舫辰, 张义飞, 杜文静. R-134a脉动热管相变蓄放热实验研究[J]. 化工学报, 2023, 74(S1): 165-171.
[4]	张义飞, 刘舫辰, 张双星, 杜文静. 超临界二氧化碳用印刷电路板式换热器性能分析[J]. 化工学报, 2023, 74(S1): 183-190.
[5]	王志国, 薛孟, 董芋双, 张田震, 秦晓凯, 韩强. 基于裂隙粗糙性表征方法的地热岩体热流耦合数值模拟与分析[J]. 化工学报, 2023, 74(S1): 223-234.
[6]	江河, 袁俊飞, 王林, 邢谷雨. 均流腔结构对微细通道内相变流动特性影响的实验研究[J]. 化工学报, 2023, 74(S1): 235-244.
[7]	吴延鹏, 刘乾隆, 田东民, 陈凤君. 相变材料与热管耦合的电子器件热管理研究进展[J]. 化工学报, 2023, 74(S1): 25-31.
[8]	宋嘉豪, 王文. 斯特林发动机与高温热管耦合运行特性研究[J]. 化工学报, 2023, 74(S1): 287-294.
[9]	张思雨, 殷勇高, 贾鹏琦, 叶威. 双U型地埋管群跨季节蓄热特性研究[J]. 化工学报, 2023, 74(S1): 295-301.
[10]	肖明堃, 杨光, 黄永华, 吴静怡. 浸没孔液氧气泡动力学数值研究[J]. 化工学报, 2023, 74(S1): 87-95.
[11]	温凯杰, 郭力, 夏诏杰, 陈建华. 一种耦合CFD与深度学习的气固快速模拟方法[J]. 化工学报, 2023, 74(9): 3775-3785.
[12]	王玉兵, 李杰, 詹宏波, 朱光亚, 张大林. R134a在菱形离散肋微小通道内的流动沸腾换热实验研究[J]. 化工学报, 2023, 74(9): 3797-3806.
[13]	袁佳琦, 刘政, 黄锐, 张乐福, 贺登辉. 泡状入流条件下旋流泵能量转换特性研究[J]. 化工学报, 2023, 74(9): 3807-3820.
[14]	何松, 刘乔迈, 谢广烁, 王斯民, 肖娟. 高浓度水煤浆管道气膜减阻两相流模拟及代理辅助优化[J]. 化工学报, 2023, 74(9): 3766-3774.
[15]	韩晨, 司徒友珉, 朱斌, 许建良, 郭晓镭, 刘海峰. 协同处理废液的多喷嘴粉煤气化炉内反应流动研究[J]. 化工学报, 2023, 74(8): 3266-3278.