T型管内油水分离特性的CFD-PBM数值模拟

doi:10.11949/j.issn.0438-1157.20161536

化工学报 ›› 2017, Vol. 68 ›› Issue (4): 1326-1335.DOI: 10.11949/j.issn.0438-1157.20161536

T型管内油水分离特性的CFD-PBM数值模拟

安杉¹, 陈家庆², 蔡小垒², 王强强², 孟迪³, 邵天泽³

1 北京化工大学机电工程学院, 北京 100029;
2 北京石油化工学院机械工程学院, 北京 102617;
3 中海石油环保服务(天津)有限公司, 天津 300456

收稿日期:2016-10-31 修回日期:2017-01-04 出版日期:2017-04-05 发布日期:2017-04-05
通讯作者: 陈家庆
基金资助:
国家自然科学基金项目(51079006)；北京市自然科学基金重点项目(KZ201410017019)。

CFD-PBM numerical simulation of oil-water separation performance inside T junction

AN Shan¹, CHEN Jiaqing², CAI Xiaolei², WANG Qiangqiang², MENG Di³, SHAO Tianze³

1 School of Mechanical and Electrical Engineering, Beijing University of Chemical Technology, Beijing 100029, China;
2 School of Mechanical Engineering, Beijing Institute of Petrochemical Technology, Beijing 102617, China;
3 CNOOC Environmental Protection Services(Tianjin) Company, Tianjin 300456, China

Received:2016-10-31 Revised:2017-01-04 Online:2017-04-05 Published:2017-04-05
Supported by:
supported by the National Natural Science Foundation of China (51079006) and the Key Program of Beijing Municipal Natural Science Foundation (KZ201410017019).

摘要/Abstract

摘要：

目前关于T型管内油水分离特性的数值模拟大多采用Euler-Euler多相流模型，考虑管内油滴粒径分布及其对油水分离特性影响的研究工作尚未见报道。对T型管内的油水两相流动情况和分离特性进行了CFD-PBM数值模拟，并进行了室内实验以验证模拟结果的准确性。结果表明，T型管内油滴粒径随流体流动方向具有逐渐增大的趋势；增大来液中的油滴粒径分布可以有效提高油水分离效率，反之当来液中的油滴粒径较小时，油水两相在T型管内不易分离，相分配比始终与分流比几乎相同；分流比、Reynolds数等操作条件对油水分离效率的影响程度与油滴粒径密切相关，应慎重选取适当的操作条件以保证T型管的油水分离效率。

关键词: T型管, 数值模拟, 计算流体力学, 相群平衡模型, 分离效率, 粒度分布

Abstract:

The Euler-Euler multi-fluid model has been widely used to simulate numerically the separation performance of oil-water mixture inside the T junction, while no study has been conducted on the oil droplet size distribution and its influence on separation performance. The CFD-PBM numerical simulation of oil-water mixture flow inside a specific T junction was carried out, and experiments were conducted in laboratory to verify the accuracy of the simulation results. It is indicated that the oil droplet size in the T junction appears a gradually increasing trend along the flow direction. With the increase of oil droplet size, the oil-water separation efficiency can be effectively promoted. On the contrary, the smaller oil droplet size leads to the difficulty of oil-water separation inside the T junction, and the fraction of phase distribution is nearly identical to the split ratio. The influence degree of operation conditions such as split ratio and Reynolds number on the separation efficiency is tightly related to the oil droplet size. Appropriate operating conditions should be selected carefully to achieve high separation efficiency for the T junction.

Key words: T junction, numerical simulation, computational fluid dynamics, population balance model, separation efficiency, size distribution

中图分类号:

TQ028.4

安杉, 陈家庆, 蔡小垒, 王强强, 孟迪, 邵天泽. T型管内油水分离特性的CFD-PBM数值模拟[J]. 化工学报, 2017, 68(4): 1326-1335.

AN Shan, CHEN Jiaqing, CAI Xiaolei, WANG Qiangqiang, MENG Di, SHAO Tianze. CFD-PBM numerical simulation of oil-water separation performance inside T junction[J]. CIESC Journal, 2017, 68(4): 1326-1335.

参考文献 32

[1]	陈家庆, 韩旭, 梁存珍, 等. 海上油田含油污水旋流气浮一体化处理设备及其应用[J]. 环境工程学报, 2012, 6(1):87-93.CHEN J Q, HAN X, LIANG C Z, et al. Compact flotation unit and its application in offshore produced water treatment[J]. Chinese Journal of Environmental Engineering, 2012, 6(1):87-93.
[2]	陈家庆, 蔡小垒, 尚超, 等. 旋流气浮一体化技术在低含油污水处理中的应用[J]. 石油机械, 2013, 41(9):62-66.CHEN J Q, CAI X L, SHANG C, et al. Application of cyclonic floatation integrated technology in low oil content sewage treatment[J]. China Petroleum Machinery, 2013, 41(9):62-66.
[3]	HART J, HAMERSMA P J, FORTUIN J M H. A model for predicting liquid route preference during gas-liquid flow through horizontal branched pipelines[J]. Chemical Engineering Science, 1991, 46(7):1609-1622.
[4]	赵立新, 徐保蕊, 叶大建, 等. 支管方向对T型管气液分离效果影响的数值模拟分析[J]. 石油化工设备, 2012, 4(5):10-13.ZHAO L X, XU B R, YE D J, et al. Numerical simulation analysis on effect of branch pipe direction to T-junction gas-liquid separator's performance[J]. Petro-Chemical Equipment, 2012, 4(5):10-13.
[5]	DAS G, DAS P K, AZZOPARDI B J. The split of stratified gas-liquid flow at a small diameter T-junction[J]. International Journal of Multiphase Flow, 2005, 31(4):514-528.
[6]	MENG Z M, WANG L S, TIAN W X, et al. Entrainment at T-junction:a review work[J]. Progress in Nuclear Energy, 2014, 70(1):221-241.
[7]	MORIKAWA Y, KONDO T, HIRAMOTO T. Pressure drop and solids distribution of air-solids mixture in horizontal unsymmetric branches[J]. International Journal of Multiphase Flow, 1978, 4(4):397-404.
[8]	NASR-EI-DIN H, SHOOK C A. Particle segregation in slurry flow through vertical tees[J]. International Journal of Multiphase Flow, 1986, 12(3):427-443.
[9]	RODRIGUEZ O M H, OLIEMANS R V A. Experimental study on oil-water flow in horizontal and slightly inclined pipes[J]. International Journal of Multiphase Flow, 2006, 32(3):323-343.
[10]	YANG L, AZZOPARDI B J, BELGHAZI A, et al. Phase separation of liquid-liquid two-phase flow at a T-junction[J]. AIChE Journal, 2006, 52(1):141-149.
[11]	YANG L, AZZOPARDI B J. Phase split of liquid-liquid two-phase flow at a horizontal T-junction[J]. International Journal of Multiphase Flow, 2007, 33(2):207-216.
[12]	AHMED W H, BADR H M, AI-SARKHI A. Experimental investigation of oil-water partial separation using a controlled tee junction[J]. Journal of Petroleum Science & Engineering, 2016, 143:187-198.
[13]	于爽, 阿斯汉, 孙策,等. T型集输管路油水两相流数值模拟[J]. 石油化工高等学校学报, 2015, 28(4):94-98.YU S, A S H, SUN C, et al. Numerical simulation on oil-water two-phase flow in T-tube of gathering pipeline[J]. Journal of Petrochemical Universities, 2015, 28(4):94-98.
[14]	范开峰, 王卫强, 阿斯汗, 等. 水平T型管中油水两相流流动数值模拟研究[J]. 石油化工高等学校学报, 2013, 26(5):75-77.FAN K F, WANG W Q, A S H, et al. The numerical simulation study of two-phase oil-water flow in horizontal T-tube[J]. Journal of Petrochemical Universities, 2013, 26(5):75-77.
[15]	杨利民, 赵振莹, 沈小明,等. 新型复合T型管对液液二相流的分离[J]. 化学工程, 2012, 40(1):43-47.YANG L M, ZHAO Z Y, SHEN X M, et al. Phase separation of liquid-liquid two-phase flow by multi-tube T-junction separator[J]. Chemical Engineering(China), 2013, 26(5):75-77.
[16]	王立洋, 郭军, 张军, 等. T型多分岔管路中的油水两相流实验研究[C]//朱德祥. 第二十一届全国水动力学研讨会暨第八届全国水动力学学术会议暨两岸船舶与海洋工程水动力学研讨会文集. 北京:海洋出版社, 2008:582-588.WANG L Y, GUO J, ZHANG J, et al. Experimental study on oil-water two-phase flow inside T-shaped pipes[C]//ZHU D X. Proceedings of Twenty-first National Water Dynamics Symposium and the Eighth National Water Dynamics Academic Conference and the Marine Engineering Water Dynamics Seminar on Cross-straits. Beijing:China Ocean Press, 2008:582-588.
[17]	WANG L Y, WU Y X, ZHENG Z C, et al. Oil-water two-phase flow inside T-junction[J]. Journal of Hydrodynamics, 2008, 20(2):147-153.
[18]	魏丛达, 许晶禹, 王立洋, 等. T型管内油水两相流动规律及其应用[J]. 油气储运, 2012, 31(12):923-926.WEI C D, XU J Y, WANG L Y, et al. The law of oil-water two-phase flow in T-shaped pipeline and its application[J]. Oil & Gas Storage & Transportation, 2012, 31(12):923-926.
[19]	丛娟, 于昭东, 黄辉才,等. T型管油水分离效率的影响因素研究[J]. 中国给水排水, 2013, 29(3):74-76.CONG J, YU Z D, HUANG H C, et al. Factors influencing oil-water separation efficiency of T-type tube[J]. China Water & Wastewater, 2013, 29(3):74-76.
[20]	CHEN J L, HE L M, LUO X M, et al. Simulation of oil-water two phase flow and separation behaviors in combined T junction[J]. Journal of Hydrodynamics, 2010, 24(6):848-857.
[21]	梅洛洛, 何利民, 许仁辞. 复合T形管内稠油-水预分离性能的研究[J]. 流体机械, 2016, 44(2):1-6.MEI L L, HE L M, XU R C. Study of heavy oil-water pre-separation performance in combined T-junctions[J]. Fluid Machinery, 2016, 44(2):1-6.
[22]	TRALLERO J L, SARICA C, ILL J P. A study of oil/water flow patterns in horizontal pipes[J]. SPE Production & Facilities, 1997, 12(3):165-172.
[23]	陈阿强, 王振波, 孙治谦. 基于相群平衡模型的浮选气泡聚并模拟[J]. 化工学报, 2015, 66(12):4780-4887.CHEN A Q, WANG Z B, SUN Z Q. Numerical simulation of bubble coalescence in dissolved air flotation tank based on population balance model[J]. CIESC Journal, 2015, 66(12):4780-4887.
[24]	陈阿强, 王振波, 王晨, 等. 气浮接触区气泡聚并行为的数值模拟[J]. 化工学报, 2016, 67(6):2301-2307.CHEN A Q, WANG Z B, WANG C, et al. Numerical simulation of bubble coalescence behavior in contact zone of dissolved air flotation tank[J]. CIESC Journal, 2016, 67(6):2301-2307.
[25]	李少伟, 景山, 张琦, 等. 萃取柱内液-液两相流CFD-PBM模拟研究进展[J]. 过程工程学报, 2012, 12(4):702-711.LI S W, JING S, ZHANG Q, et al. Advances in simulation of liquid-liquid two-phase flow in extraction columns with CFD-PBM[J]. The Chinese Journal of Process Engineering, 2012, 12(4):702-711.
[26]	李孟, 李向阳, 王宏智, 等. 鼓泡塔气液两相流不同曳力模型的数值模拟[J]. 过程工程学报, 2015, 15(2):181-189.LI M, LI X Y, WANG Z H, et al. Numerical simulation of gas-liquid two-phase flow in a bubble column with various drag models[J]. The Chinese Journal of Process Engineering, 2015, 15(2):181-189.
[27]	KLINK I M, PHILLIPS R J, DUNGAN S R. Effect of emulsion drop-size distribution upon coalescence in simple shear flow:a population balance study[J]. Journal of Colloid and Interface Science, 2011, 353(2):467-475.
[28]	ENGL W, BACKOV R, PANIZZA P. Controlled production of emulsions and particles by milli-and microfluidic techniques[J]. Current opinion in Colloid & Interface Science, 2008, 13(4):206-216.
[29]	覃成鹏, 杨宁. 多相分散体系中气泡/液滴聚并和破碎的群平衡模拟[J]. 化学进展, 2016, 28(8):1207-1223.QIN C P, YANG N. Population balance modeling of breakage and coalescence of dispersed bubbles or droplets in multiphase system[J]. Progress in Chemistry, 2016, 28(8):1207-1223.
[30]	刘世平, 李佟茗, 贾绍义. 两个液滴之间的聚并[J]. 物理化学学报, 1995, 11(11):997-1003.LIU S P, LI T M, JIA S Y. Coalescence between two small liquid drops[J]. Acta Physico-Chimica Sinica, 1995, 11(11):997-1003.
[31]	桑义敏, 陈家庆, 易国庆, 等. 水包油型乳化液油滴的管内节流破碎行为与机理[J]. 过程工程学报, 2015, 15(6):940-944.SANG Y M, CHEN J Q, YI G Q, et al. Break-up behaviors and mechanism of oil-in-water emulsion droplets through a pipe restriction[J]. The Chinese Journal of Process Engineering, 2015, 15(6):940-944.
[32]	王艺, 陈雷. 聚结除油反应机理及其动力学分析[J]. 环境工程学报, 2006, 7(1):59-63.WANG Y, CHEN L. Analysis of coalescence mechanism and coalescence reaction dynamics[J]. Chinese Journal of Environmental Engineering, 2006, 7(1):59-63.

T型管内油水分离特性的CFD-PBM数值模拟

CFD-PBM numerical simulation of oil-water separation performance inside T junction

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献 32

相关文章 15

编辑推荐

Metrics

本文评价

[1]	叶展羽, 山訸, 徐震原. 用于太阳能蒸发的折纸式蒸发器性能仿真[J]. 化工学报, 2023, 74(S1): 132-140.
[2]	张义飞, 刘舫辰, 张双星, 杜文静. 超临界二氧化碳用印刷电路板式换热器性能分析[J]. 化工学报, 2023, 74(S1): 183-190.
[3]	王志国, 薛孟, 董芋双, 张田震, 秦晓凯, 韩强. 基于裂隙粗糙性表征方法的地热岩体热流耦合数值模拟与分析[J]. 化工学报, 2023, 74(S1): 223-234.
[4]	宋嘉豪, 王文. 斯特林发动机与高温热管耦合运行特性研究[J]. 化工学报, 2023, 74(S1): 287-294.
[5]	张思雨, 殷勇高, 贾鹏琦, 叶威. 双U型地埋管群跨季节蓄热特性研究[J]. 化工学报, 2023, 74(S1): 295-301.
[6]	肖明堃, 杨光, 黄永华, 吴静怡. 浸没孔液氧气泡动力学数值研究[J]. 化工学报, 2023, 74(S1): 87-95.
[7]	温凯杰, 郭力, 夏诏杰, 陈建华. 一种耦合CFD与深度学习的气固快速模拟方法[J]. 化工学报, 2023, 74(9): 3775-3785.
[8]	何松, 刘乔迈, 谢广烁, 王斯民, 肖娟. 高浓度水煤浆管道气膜减阻两相流模拟及代理辅助优化[J]. 化工学报, 2023, 74(9): 3766-3774.
[9]	邢雷, 苗春雨, 蒋明虎, 赵立新, 李新亚. 井下微型气液旋流分离器优化设计与性能分析[J]. 化工学报, 2023, 74(8): 3394-3406.
[10]	汪林正, 陆俞冰, 张睿智, 罗永浩. 基于分子动力学模拟的VOCs热氧化特性分析[J]. 化工学报, 2023, 74(8): 3242-3255.
[11]	韩晨, 司徒友珉, 朱斌, 许建良, 郭晓镭, 刘海峰. 协同处理废液的多喷嘴粉煤气化炉内反应流动研究[J]. 化工学报, 2023, 74(8): 3266-3278.
[12]	程小松, 殷勇高, 车春文. 不同工质在溶液除湿真空再生系统中的性能对比[J]. 化工学报, 2023, 74(8): 3494-3501.
[13]	刘文竹, 云和明, 王宝雪, 胡明哲, 仲崇龙. 基于场协同和耗散的微通道拓扑优化研究[J]. 化工学报, 2023, 74(8): 3329-3341.
[14]	洪瑞, 袁宝强, 杜文静. 垂直上升管内超临界二氧化碳传热恶化机理分析[J]. 化工学报, 2023, 74(8): 3309-3319.
[15]	岳林静, 廖艺涵, 薛源, 李雪洁, 李玉星, 刘翠伟. 凹坑缺陷对厚孔板喉部空化流动特性影响研究[J]. 化工学报, 2023, 74(8): 3292-3308.