板式换热器相变流动的传热及压降特性

doi:10.11949/j.issn.0438-1157.20170623

化工学报 ›› 2017, Vol. 68 ›› Issue (S1): 133-140.DOI: 10.11949/j.issn.0438-1157.20170623

板式换热器相变流动的传热及压降特性

吴学红, 李灿, 龚毅, 张军, 赵敏

郑州轻工业学院能源与动力工程学院, 河南郑州 450002

收稿日期:2017-05-15 修回日期:2017-05-25 出版日期:2017-08-31 发布日期:2017-08-31
通讯作者: 吴学红,wuxh1212@163.com
基金资助:
国家自然科学基金项目（51476149）；河南省杰出青年基金项目（154100510014）；河南省教育厅创新人才团队项目（17IRTSTHN029）。

Heat transfer and pressure drop characteristic of phase change flow in plate heat exchanger

WU Xuehong, LI Can, GONG Yi, ZHANG Jun, ZHAO Min

School of Energy and Power Engineering, Zhengzhou University of Light Industry, Zhengzhou 450002, Henan, China

Received:2017-05-15 Revised:2017-05-25 Online:2017-08-31 Published:2017-08-31
Supported by:
supported by the National Natural Science Foundation of China (51476149),the Excellent Youth Foundation of Henan Scientific Committee(154100510014) and the Innovative Research Team (in Science and Technology) in University of Henan Province(17IRTSTHN029).

摘要/Abstract

摘要：

建立了三维单流道模型，模拟了波纹倾角和波纹节距对相变流动传热和压降特性的影响。结果表明，沸腾传热和压降特性同时受到流动形式和触点影响，"曲折型"流动有利于液膜蒸发增强传热，触点对气相的扰动作用小于液相，因此在气相体积分数较高的区域的触点处气液相变转化现象不明显。传热系数随波纹倾角的增加而增大，随波纹节距的增加而减小，但在相同入口Reynolds数下波纹节距λ=16 mm比14 mm的传热系数大，主要是因为流动形式的改变在某种程度上减弱了触点数目减少对传热的影响。β=75°和λ=10 mm时传热性能最好。沸腾流动的压降随波纹倾角的增大先升高后降低，在β=65°左右达到峰值，随着波纹节距的增大而降低。

关键词: 板式换热器, 气液两相流, 相变, 传热, 压降, 数值模拟

Abstract:

A three-dimensional one-channel model was established,the effect of corrugated clination angle and corrugated pitch on heat transfer and pressure drop of phase change flow was simulated. The results show that the heat transfer characteristics of the flow boiling are affected by both the flow pattern and the contact point. The “helical flow” promots evaporation of liquid film,and the contact point has less effect on gas than liquid,therefore,the phenomenon of gas-liquid phase transition is not obvious at the higher gas volume fraction. The heat transfer coefficient increases with the increasing of the corrugated inclination angle,and decreases with the increasing of the corrugated pitch. The heat transfer coefficient of λ=16 mm is larger than that of λ=14 mm at same Reynolds number,because the change of the flow pattern may prevent the heat transfer caused by the reduction of the number of contacts. The heat transfer is the best at β=75° and λ=10 mm.The pressure drop of the flow boiling increases at first and then decreases with the increasing of the corrugated inclination angle,and reaches the peak at about β=65°,and decreases with the increasing of the corrugation pitch.

Key words: plate heat exchanger, gas-liquid flow, phase change, heat transfer, pressure drop, numerical simulation

中图分类号:

TK124

吴学红, 李灿, 龚毅, 张军, 赵敏. 板式换热器相变流动的传热及压降特性[J]. 化工学报, 2017, 68(S1): 133-140.

WU Xuehong, LI Can, GONG Yi, ZHANG Jun, ZHAO Min. Heat transfer and pressure drop characteristic of phase change flow in plate heat exchanger[J]. CIESC Journal, 2017, 68(S1): 133-140.

参考文献 30

[1]	程宝华,李先瑞. 板式换热器及换热装置技术应用手册[M]. 北京:中国建筑工业出版社,2005. CHENG B H,LI X R. Technical Application Manual of Plate Heat Exchangers[M]. Beijing:China Architecture and Building Press,2005.
[2]	张灿灿,王定标,韩勇,等. 基于耗散热阻的新型蜂窝板式换热器性能分析[J]. 化工学报,2016,67(S1):111-116. ZHANG C C,WANG D B,HAN Y,et al. Performance analysis of novel honeycombed plate heat exchanger based on entransy dissipation resistance[J].CIESC Journal,2016,67(S1):111-116.
[3]	聂泽森,毕勤成,高彬. 新型板式换热器的传热与流动特性[J]. 工程热物理学报,2014,35(10):2041-2044. NIE Z S,BI Q C,GAO B. Heat transfer and flow characteristics of a new type plate heat exchanger[J]. Journal of Engineering Thermophysics,2014,35(10):2041-2044.
[4]	苏国萍,张建丽,周洪光,等. 板式蒸发器冷凝侧传热及压降性能实验研究[J].中国科学院大学学报,2015,32(3):295-300. SU G P,ZHANG J L,ZHOU H G,et al. Experimental study on the characteristics of heat transfer and pressure drop of steam condensation in desalination plate evaporator[J]. Journal of University of Chinese Academy of Sciences,2015,32(3):295-300.
[5]	乔宏斌,王顺,胡申华. 水-酒精混合蒸汽在板式换热器中凝结时的压降特性[J].动力工程学报,2017,37(1):33-38. QIAO H B,WANG S,HU S H. Pressure drop in plate heat exchanger during condensation of ethanol-water mixed vapor[J].Journal of Chinese Society of Power Engineering,2017,37(1):33-38.
[6]	DEVECEO A?G LU A G,ORUÇ V. The influence of plate-type heat exchanger on energy efficiency and environmental effects of the air-conditioners using R453a as a substitute for R22[J]. Applied Thermal Engineering,2017,112:1364-1372.
[7]	HAYES N,JOKAR A,AYUB Z H. Study of carbon dioxide condensation in chevron plate exchangers; pressure drop analysis[J]. International Journal of Heat and Mass Transfer,2012,55(11/12):2916-2925.
[8]	HU S,MA X,ZHOU W. Condensation heat transfer of ethanol-water vapor in a plate heat exchanger[J]. Applied Thermal Engineering,2017,113:1047-1055.
[9]	MAMOURIAN M,SHIRVAN K M,MIRZAKHANLARI S. Two phase simulation and sensitivity analysis of effective parameters on turbulent combined heat transfer and pressure drop in a solar heat exchanger filled with nanofluid by response surface methodology[J]. Energy,2016,109:49-61.
[10]	WANG P L,LI D C,HUANG Y,et al. Numerical study of solidification in a plate heat exchange device with a zigzag configuration containing multiple phase-change-materials[J]. Energies,2016,9(6):394.
[11]	彭建军,胡申华,木黑提·吾肯. 不同压力下混合蒸气在板式换热器凝结特性[J]. 实验室研究与探索,2015,34(4):53-56. PENG J J,HU S H,MUHIT O. Condensation of water-ethanol mixture in plate heat exchanger under different pressures[J]. Research and Exploration in Laboratory,2015,34(4):53-56.
[12]	徐志明,胡春阳,王景涛,等板式换热器黏液形成菌与CaCO3混合污垢实验[J]. 化工学报,2017,68(1):72-78. XU Z M,HU C Y,WANG J T,et al. Mixed fouling characteristics of CaCO3 and sline forming bacteria in plate heat exchanger[J].CIESC Journal,2017,68(1):72-78.
[13]	李明春,肖刚,史和春,等. 人字形波纹板相变流动及换热特性研究[J]. 工程热物理学报,2016,37(3):581-585. LI M C,XIAO G,SHI H C,et al. Study on phase change flow and heat transfer characteristics of chevron corrugated plate[J]. Journal of Engineering Thermophysics,2016,37(3):581-585.
[14]	SOLOTYCH V,LEE D,KIM J,et al. Boiling heat transfer and two-phase pressure drops within compact plate heat exchangers:experiments and flow visualizations[J]. International Journal of Heat and Mass Transfer,2016,94:239-253.
[15]	董俐言,王宝龙,石文星,等. 板式蒸发式冷凝器传热传质的数值模拟[J]. 制冷学报,2013,34(1):10-17. DONG L Y,WANG B L,SHI W X,et al. Numerical simulation on heat and mass transfer of plate evaporative condenser[J]. Journal of Refrigeration,2013,34(1):10-17.
[16]	AMALFI R L,THOME J R,SOLOTYCH V,et al. High resolution local heat transfer and pressure drop infrared measurements of two-phase flow of R245fa within a compact plate heat exchanger[J]. International Journal of Heat and Mass Transfer,2016,103:791-806.
[17]	KHAN T S,KHAN M S,CHYU M C,et al. Experimental investigation of evaporation heat transfer and pressure drop of ammonia in a 60° chevron plate heat exchanger[J]. International Journal of Refrigeration,2012,35(2):336-348.
[18]	SHI Z Y,CHEN J P,GRABENSTEIN V,et al. Experimental investigation on condensation heat transfer and pressure drop of R134a in a plate heat exchanger[J]. Heat and Mass Transfer,2010,46(10):1177-1185.
[19]	ZHANG J,DESIDERI A,KÆRN M R,et al. Flow boiling heat transfer and pressure drop characteristics of R134a,R1234yf and R1234ze in a plate heat exchanger for organic rankine cycle units[J]. International Journal of Heat and Mass Transfer,2017,108:1787-1801.
[20]	IMRAN M,USMAN M,YANG Y,et al. Flow boiling of R245fa in the brazed plate heat exchanger:thermal and hydraulic performance assessment[J]. International Journal of Heat and Mass Transfer,2017,110:657-670.
[21]	BAMOROVAT A G,KIM D Y,YOON S Y,et al. Thermal performance of a 10-kW phase-change plate heat exchanger with metal foam filled channels[J]. Applied Thermal Engineering,2016,99:790-801.
[22]	LONGO G A. The effect of vapour super-heating on hydrocarbon refrigerant condensation inside a brazed plate heat exchanger[J]. Experimental Thermal and Fluid Science,2011,35(6):978-985.
[23]	MANCIN S,DEL C D,ROSSETTO L. R32 partial condensation inside a brazed plate heat exchanger[J]. International Journal of Refrigeration,2013,36(2):601-611.
[24]	SARRAF K,LAUNAY S,TADRIST L. Analysis of enhanced vapor desuperheating during condensation inside a plate heat exchanger[J]. International Journal of Thermal Sciences,2016,105:96-108.
[25]	ASANO H,TAKENAKA N,WAKABAYASHI T,et al. Visualization and void fraction distribution of downward gas-liquid two-phase flow in a plate heat exchanger by neutron radiography[J]. Nuclear Instruments and Methods in Physics Research Section A:Accelerators,Spectrometers,Detectors and Associated Equipment,2005,542(1/2/3):154-160.
[26]	GRABENSTEIN V,POLZIN A E,KABELAC S. Experimental investigation of the flow pattern,pressure drop and void fraction of two-phase flow in the corrugated gap of a plate heat exchanger[J]. International Journal of Multiphase Flow,2017,91:155-169.
[27]	NILPUENG K,WONGWISES S. Two-phase gas-liquid flow characteristics inside a plate heat exchanger[J]. Experimental Thermal and Fluid Science,2010,34(8):1217-1229.
[28]	ROHMAH N,PIKRA G,PURWANTO A J,et al. The effect of plate spacing in plate heat exchanger design as a condenser in organic rankine cycle for low temperature heat source[J]. Energy Procedia,2015,68:87-96.
[29]	WANG P,WANG X,HUANG Y,et al. Thermal energy charging behaviour of a heat exchange device with a zigzag plate configuration containing multi-phase-change-materials (m-pcms)[J]. Applied Energy,2015,142:328-336.
[30]	DJORDJEVIC E,KABELAC S. Flow boiling of R134a and ammonia in a plate heat exchanger[J]. International Journal of Heat and Mass Transfer,2008,51(25/26):6235-6242.

板式换热器相变流动的传热及压降特性

Heat transfer and pressure drop characteristic of phase change flow in plate heat exchanger

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献 30

相关文章 15

编辑推荐

Metrics

本文评价

[1]	叶展羽, 山訸, 徐震原. 用于太阳能蒸发的折纸式蒸发器性能仿真[J]. 化工学报, 2023, 74(S1): 132-140.
[2]	张双星, 刘舫辰, 张义飞, 杜文静. R-134a脉动热管相变蓄放热实验研究[J]. 化工学报, 2023, 74(S1): 165-171.
[3]	张义飞, 刘舫辰, 张双星, 杜文静. 超临界二氧化碳用印刷电路板式换热器性能分析[J]. 化工学报, 2023, 74(S1): 183-190.
[4]	陈爱强, 代艳奇, 刘悦, 刘斌, 吴翰铭. 基板温度对HFE7100液滴蒸发过程的影响研究[J]. 化工学报, 2023, 74(S1): 191-197.
[5]	刘明栖, 吴延鹏. 导光管直径和长度对传热影响的模拟分析[J]. 化工学报, 2023, 74(S1): 206-212.
[6]	王志国, 薛孟, 董芋双, 张田震, 秦晓凯, 韩强. 基于裂隙粗糙性表征方法的地热岩体热流耦合数值模拟与分析[J]. 化工学报, 2023, 74(S1): 223-234.
[7]	江河, 袁俊飞, 王林, 邢谷雨. 均流腔结构对微细通道内相变流动特性影响的实验研究[J]. 化工学报, 2023, 74(S1): 235-244.
[8]	吴延鹏, 刘乾隆, 田东民, 陈凤君. 相变材料与热管耦合的电子器件热管理研究进展[J]. 化工学报, 2023, 74(S1): 25-31.
[9]	宋嘉豪, 王文. 斯特林发动机与高温热管耦合运行特性研究[J]. 化工学报, 2023, 74(S1): 287-294.
[10]	张思雨, 殷勇高, 贾鹏琦, 叶威. 双U型地埋管群跨季节蓄热特性研究[J]. 化工学报, 2023, 74(S1): 295-301.
[11]	晁京伟, 许嘉兴, 李廷贤. 基于无管束蒸发换热强化策略的吸附热池的供热性能研究[J]. 化工学报, 2023, 74(S1): 302-310.
[12]	程成, 段钟弟, 孙浩然, 胡海涛, 薛鸿祥. 表面微结构对析晶沉积特性影响的格子Boltzmann模拟[J]. 化工学报, 2023, 74(S1): 74-86.
[13]	袁佳琦, 刘政, 黄锐, 张乐福, 贺登辉. 泡状入流条件下旋流泵能量转换特性研究[J]. 化工学报, 2023, 74(9): 3807-3820.
[14]	齐聪, 丁子, 余杰, 汤茂清, 梁林. 基于选择吸收纳米薄膜的太阳能温差发电特性研究[J]. 化工学报, 2023, 74(9): 3921-3930.
[15]	李艺彤, 郭航, 陈浩, 叶芳. 催化剂非均匀分布的质子交换膜燃料电池操作条件研究[J]. 化工学报, 2023, 74(9): 3831-3840.